Panasonic Matrix Switcher Wj Sx550c Operating Instructions

43
2
SW1 Setting
These switches are used only for factory test.
Always keep these switches in the “OFF” positions
in the field.
Board Setting
Before installing this board, the following settings should be made by qualified service per-
sonnel or system installers.
1. Set switches (SW1) on the board to designate the data board number as shown in the
following table.
The factory default setting is Board Number 1.
1234OFFSW11234OFF
SW3SW100
SW150
SW200
SW250
SW300
SW350
SW400
SW450
SW5
SW6
Board
No.
1234...

44
2
This switcher has 15 slots, eleven of which are available for system expansion.
The CPU and Control Board, along with one Video Input Board and one Video Output Board are supplied as standard acces-
sories.
Depending on the number of camera inputs and monitor outputs required, additional WV-PB5508 Video Input Boards and WV-
PB5504A Video Output Boards will be required.
WJ-SX550C Matrix Switcher
5 4 3 2 167891011121314 15
OFF
+9V+5V−5V
POWER
ON
11A00001
Extension
1
2
WJ-SX550A
Extension
1
2
DATA...

45
2
The tables below show the components required for various system configurations.
Cameras
Cameras
1 - 8
9 - 16
17 - 24
25 - 32
33 - 40
41 - 48
49 - 56
57 - 641 - 4
1 - 4
1 - 4
1 - 4
1 - 4
1 - 4
1 - 4
1 - 4not required
not required
not required
not required
not required
not required
not required
not required1
1
1
1
1
1
1
14
5
6
7
8
9
10
1111
10
9
8
7
6
5
4 MonitorsExtension Unit
WJ-AD550Output Boards
WV-PB5504A
1
2
3
4
5
6
7
8
65 - 72 1 - 4 required 2 15 159
73 - 80 1 - 4 required 2 16 1410
81 - 88 1...

46
2
Cameras
1 - 8
9 - 16
17 - 24
25 - 32
33 - 40
41 - 48
49 - 56
57 - 649 - 12
9 - 12
9 - 12
9 - 12
9 - 12
9 - 12
9 - 12
9 - 12not required
not required
not required
not required
not required
not required
not required
not required3
3
3
3
3
3
3
36
7
8
9
10
11
12
139
8
7
6
5
4
3
2 MonitorsExtension Unit
WJ-AD550Output Boards
WV-PB5504A
1
2
3
4
5
6
7
8
65 - 72 9 - 12 required 6 19 119
73 - 80 9 - 12 required 6 20 1010
81 - 88 9 - 12 required 6 21 911
89 - 96 9 - 12 required 6 22 812
97 - 104 9 - 12...

47
3
SECTION 3
INSTALLATION
AND
SYSTEM CONNECTIONS 

48
3
INSTALLATIONS
Remove screws.
Side Panel
Palm-rest
Remove Screws.
Rubber
feet
Rack Mount Screws
Rubber
feet
WJ-SX550C Matrix Switcher
WJ-AD550 Extension Unit
Mounting into the Rack
1. Remove four rubber feet by removing four screws from
the bottom of the Matrix Switcher (Extension Unit).
2. Install the Matrix Switcher (Extension Unit) in the rack
securing it with eight screws (not included).
• The cooling fans inside the Matrix Switcher (or Extension Unit) are subject to wear and need to be...

49
3
Each slot is identical, so the boards can be installed
in any slot.
However it is recommended to install the boards as
shown below for orderly installation.
Installing Additional Extension Boards
Before installing the additional extension boards, be sure to make the specified board settings.
Refer to the board settings for each board in section 2 for further details.
Extension Unit is not Required
Before installing any boards be sure to turn the power of
the Matrix Switcher off.
Caution
1. Remove...

50
3
Extension Unit is required
Before installing any boards, be sure to turn the power
of the WJ-SX550C Matrix Switcher and WJ-AD550
Extension Unit off.
Caution
When the Extension Unit is required to install the
boards, follow the procedures as shown below.
•Removing Extension Boards
1. Remove the screws from rear panel(s) of the
Extension Unit.
2. Remove the rear panel(s).
3. Loosen two screws on the Extension Board(s).
4. Extract the Extension Board(s) from the rear of the
Extension Unit by sliding...

51
3
SYSTEM CONNECTIONS
TLTL
TLTL
CPURS-232C
TIME
ADJUST IN
COM
PRINTER
OUT    IN
VS/VD
VD
OUT
OFF
+9V+5V−5V
POWERON
11A00001
OUT    IN1
OUT    IN2
OUT
   IN3
OUT    IN4
MONITORALARM OUT
RESET OUT
EXT TIMING IN
RECOVER  IN
OUTPUT
MONITORALARM OUT
RESET OUT
EXT TIMING IN
RECOVER  INMONITORALARM OUT
RESET OUT
EXT TIMING IN
RECOVER  IN
OUT    IN1
OUT    IN2
OUT
   IN3
OUT    IN4
OUTPUT
OUT
   IN1
OUT    IN2
OUT
   IN3
OUT    IN4
OUTPUTCONTROLDATA 1
DATA 2
DATA 3
DATA 4
DATA 5
DATA 6
DATA 7
DATA 8
TEST 1...

52
3
Connection with the Camera Sites
Connect the Camera Site Equipment to the Camera Input Connectors (CAMERA IN, 1-8) on the Video Input Board(s).
Note:Make sure that the cable length between the camera site and the WJ-SX550C Matrix Switcher is less than 900 m
(3 000 ft) when using RG-59/U, BELDEN 9259 or equivalent cable.
INPUT
1
2
3
4
5
6
7
8
CAMERA IN
VIDEO OUT1
VIDEO OUT2
Camera 1 - 4
Video Input Board
WV-CA64
WV-CA51
WV-RC100 WV-RC150 WV-RC150WV-CA50 WV-CA50 (Video Active Loop Throught Out)...