Panasonic Matrix Switcher Wj Sx550c Operating Instructions

23
2
qOperate Indicator (OPERATE)
Is on when the power of the WJ-SX550C Matrix
Switcher is turned on.
wCPU Board (CPU)
A personal computer and printer can be connected to
this board.
Refer to the CPU Board on page 24 for more details.
eControl Board (CONTROL)
The system controllers can be connected to this board.
Refer to the Control Board on page 27 for more details.
rVideo Input Board (INPUT)
The cameras and receivers are connected to this
board.
Refer to the Video Input Board on page 29 for more...

Printer ←Switcher
Printer ←Switcher
Printer ←Switcher
Printer ←Switcher
Printer ←Switcher
Printer ←Switcher
Printer ←Switcher
Printer ←Switcher
Printer ←Switcher
Printer →Switcher
Printer →Switcher
Monitor ←Switcher
Monitor ←Switcher
Monitor ←Switcher
Monitor ←Switcher
Printer ←Switcher
24
2
Pin No.
CPURS-232C
TIME
ADJUST IN
COM
PRINTER
OUT    IN
VS/VD
VD
OUT
q
w
e
r
t
y
wTime Adjustment Input Connector (TIME ADJUST IN)
Accepts the time adjustment signal from a Time Lapse VCR.  It enables the time...

25
2
rVS/VD Input Connector (VS/VD IN)
Accepts either the VD (Vertical Drive) pulse or the VS (Video Sync) signal for synchronizing the system.
Notes:
• This input is looped through to the VS/VD Output Connector.
• When the VD (or VS) signal is supplied to the VS/VD Input Connector, turn the VD/VS selection switch (SW4) on the cir-
cuit board to the VD (or VS) position. The factory default setting of the VD/VS selection switch (SW4) is VS.  Ask quali-
fied service personnel about setting up this switch....

26
2
Board Setting
Before installing this board, the following settings should be made by qualified service personnel or system installers.
CN13 CN12
SW4
CN14
1234
OFF
5678SW2
1. Confirm that Switches (SW2) on the board are set as
follows.
1234
OFF
SW25678
2. Set switch (SW4) on the board to select either VD or VS
for the Sync input signal, if applicable.
The factory default setting is VS.
SW4
SW4 VS
VD
3. Position jumper connectors (CN12) on the board to
open connection position when a printer is...

27
2
Pin No.
Control Board
Appearance
qData Ports (DATA 1 - 8)
For exchanging control data with the WV-CU550C System Controller.  Eight ports are avail-
able on the board.  Connect supplied 6-conductor modular cable or use a data grade
shielded 4-wire twisted pair cable suitable for RS-485 communication. Cable length may
be extended up to 1 200 m (4 000 ft).
6
1Designation Direction
1
2
3
4
5
6Ground
RB
RA
TB
TA
GroundSwitcher ←Controller
Switcher ←Controller
Switcher →Controller
Switcher  →...

28
2
1234
OFF
SW2
CN13
Board Setting
Before installing this board, the following settings should be made by qualified service personnel or system installers.
1234
OFF
SW2
1. Confirm that switches (SW2) on the board are set as follows.
These switches are used only for factory test.
Always keep these switches in the “OFF” positions in the field.
Note
2. Position jumper connector (CN13) on the board as shown below.
Open:When the controllers are connected in a “Home Run” connection.
Closed:When the...

29
2
Pin No.
WV-PB5508 Video Input Board
Appearance
qVideo Output Ports (VIDEO OUT 1, 2)
The video signal connected to the Camera Input Connector (CAMERA IN) is present at
these ports.
The camera control data multiplexed on the video signal is not available at these ports.
When the power of the Matrix Switcher is turned off, no signal is present at these ports.
BNC female connectors are available for conversion by use of optional WV-CA64 loop
through cable.
INPUT
1
2
3
4
5
6
7
8
CAMERA IN
VIDEO OUT1...

Camera
In No. Board
No.
30
2
1234
OFFSW 1
Board Setting
Before installing this board, the following setting should be made by qualified service personnel or system installers.
Set switches (SW1) on the board to designate the camera input board number as shown in the following table.
The factory default setting is Board Number 1.
1234
OFF
1234
OFF
1234
OFF
1234
OFF
1234
OFF
1234
OFF
1234
OFF
1234
OFF
1234
OFF
1234
OFF
1234
OFF
1234
OFF
1234
OFF
1234
OFF
1234
OFF
1234
OFF
1
2
3
4
5
6
7
8
9
10
11
12
13
14...

31
2
Pin No.
WV-PB5504A Video Output Board
Appearance
qAlarm Output/Reset Output Connector (ALARM OUT/RESET OUT)
External Timing Input Connector (EXT TIMING IN)
Recover Input Connector (RECOVER IN)
ALARM OUT:When the Matrix Switcher receives an alarm from the WV-PB5564 Alarm
Board or camera site receivers WV-RC100 or WV-RC150, the alarm output signal is
provided at this connector for the Time Lapse VCR. 
The active pin number of the alarm output depends on the alarm mode set by the
on-screen program...

3. Set switches (SW100/SW150/SW200/SW250) on the
board to meet the character display requirement on the
monitor screen.
The factory default setting is normal (NOR).
NOR:White with Black border
REV:Black with White border
4. Confirm that switches (SW6) on the board are set as
follows.2. Set switches (SW2/SW3/SW4/SW5) on the board to
meet the alarm reset output requirement as either Open
Collector (OPEN C.) or Pulse (VTR).
The factory default setting is Pulse (VTR).
Open Collector (OPEN C.):16 V DC 100 mA...