Panasonic Matrix Switcher Wj Sx550c Operating Instructions

33
2
WV-CU550C System Controller
Appearance
Front View
123
456
789
MON CAM
ESC SET0
ACK
RESETBACK
SEQFORWARD
SEQALT
DEC
–1CAMINC
+1CAM STOP
SLOW12AUX
CLOSEOPEN IRISPRESET
FOCUS
NEAR ZOOM
TELE
FAR WIDE
System Controller WV-CU550
LEFT RIGHTUP
DOWN
ALARMBUSY
F3F4F2F1
C
AF
qwert
y
uio!0!1!2!3!4!5!6!7 @1 !9
!8
@0
CONTROLLER
ON OFFINOUTTERMON OFF
DATA
0123456789
CONTROLLER
UNIT NO.
1-8MODE
#1#2#3#4#5#6
Rear View 

34
2
qAlarm Indicator (ALARM)
Blinks to indicate that an alarm condition exists.
To turn the indicator off, press the ACK RESET button.
wBusy Indicator (BUSY)
Lights up when you attempt to control a monitor or a
camera that is already used by a higher priority opera-
tor, or when the higher priority operator selects the
monitor or camera you are currently operating.
Operations from the System Controller are disabled
until this indicator goes off.
eFunction Buttons (F1/F2/F3/F4)
Select functions displayed...

35
2
#4Mode Selection Switch (MODE)
These switches are used to set the mode of the System
Controller connected to the Matrix Switcher. Set the
switches as shown below.
#5Controller On/Off Switch (CONTROLLER ON/OFF)
This switch is used to turn the WV-CU550C system
controller power on and off.
#6Power Cord !7Auxiliary Button (AUX 1,2)
These buttons toggle the auxiliary switches in the
Receiver on and off.
The auxiliary switches can be used, for example, to
activate equipment connected to the receiver, such...

36
2
OPERATE
Extension Unit  WJ-AD550
q
WJ-AD550 Extension Unit
Appearance
Front View
OFF
+9V+5V−5V
POWER
ON
11A00001
Extension
1
2
WJ-SX550A
Extension
1
2
DATA
ADDRESS12345678
ON OFFDATA
ADDRESS12345678
ON OFF
WJ-AD550WJ-SX550AWJ-AD550
w
e
r
t
y
Rear View
qOperate Indicator (OPERATE)
Is on when the power of the WJ-AD550 Extension Unit
is turned on.
wExtension Board (EXTENSION)
One of these boards is installed in the WJ-SX550C
Matrix Switcher.  Connect these boards using the 25-
pin connection cables...

37
2
Extension Board
Appearance
qExtension Port (1, 2)
These ports are used to expand the Matrix Switcher System. 
Connect between these ports on the boards installed in the WJ-SX550C Matrix
Switcher and the WJ-AD550 Extension Unit.
wData Address Switch (DATA ADDRESS ON/OFF)
These switches are used to identify the unit address number of the WV-PB5548 Data
Board installed in the WJ-AD550 Extension Unit.
Set switches on the board installed in the WJ-SX550C Matrix Switcher to the “ON” posi-
tion designate...

38
2
Board Setting
Before installing this board, the following settings should be made by qualified service personnel or system installers.
SW1
AD550 SX550A
SW3
AD550 SX550A
1. Set switches (SW1 and SW3) on the board to reflect the system configuration as shown below.
SX550A:Set to this position when the board is installed in the WJ-SX550C Matrix Switcher.
AD550:Set to this position when the board is installed in the WJ-AD550 Extension Unit.
The factory default setting is AD550 position.
SW1
AD550...

39
2
WV-PB5564 Alarm Board
Appearance
qAlarm Number Display
Indicates the alarm input number when an alarm is received from the  associated alarm
sensor.
Note:The display indicator lights up as shown below when the alarm number is over
one hundred.
ALARM
TEST
1-32
5
RESET
MODE
33-64
q
w
e
r
tIndicator
wMode Selection Switch (MODE)
This rotary switch, in combination with the Test button, is used to select the alarm test
mode.
Mode 0:Press the Test button to receive an alarm number display in...

40
2
Alarm Signal
tAlarm Input Port (1-32, 33-64)
This port accepts alarm input from the associated alarm sensors through either Normally Open or Normally Closed con-
tacts.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19Alarm 1
Alarm 2
Alarm 3
Alarm 4
Alarm 5
Alarm 6
Alarm 7
Alarm 8
Alarm 9
Alarm 10
Alarm 11
Alarm 12
Alarm 13
Alarm 14
Alarm 15
Alarm 16
Alarm 17
Alarm 18
Alarm 19Alarm 65
Alarm 66
Alarm 67
Alarm 68
Alarm 69
Alarm 70
Alarm 71
Alarm 72
Alarm 73
Alarm 74
Alarm 75
Alarm 76
Alarm 77
Alarm78...

41
2
SW1 Setting
1. Set switches (SW1) on the board to designate the
Alarm Input board number as shown below.
1
12OFF
SW1
12OFF
SW12 UNIT ADR
SW4
2SW5
3SW6
4SW7
5SW8
6SW9
7SW10
8SW11
2. Set switches (SW4, SW5, SW6, SW7, SW8, SW9, SW10 and SW11) on the board to meet the alarm input requirements.
NOR OPEN:Normally Open Input
NOR CLOSE:Normally Closed Input
The factory default setting is Normally Open (NOR OPEN).
Board No.
12
OFF
12
OFF
1
21-64
65-128Alarm
Input No.
1
2
OFF
SW1
UNIT ADR
65-72
73-80
81-88...

42
2
WV-PB5548 Data Board
Appearance
qData Connector (TA/TB/RA/RB/G, 1 - 8)
These connectors are used to exchange control data with the camera site equipment.
For connection, use a data grade shielded 4-wire twisted pair cable suitable for RS-485
communication. Cable length may be extended up to 1 200 m (4 000 ft).
DATA(RS485)
A
T
B
1A
R
B
G
A
T
B
2A
R
B
G
A
T
B
3A
R
B
G
A
T
B
4A
R
B
G
A
T
B
5A
R
B
G
A
T
B
6A
R
B
G
A
T
B
7A
R
B
G
A
T
B
8A
R
B
G
q
TB
RA (+)
RB
GNDR
T
TA (+)
S W
1
RT: Termination...