Panasonic Matrix Switcher Wj Sx550c Operating Instructions

96
5
Power Up Display
When the power switch of the Matrix Switcher is turned on, a screen similar to the one shown below is displayed on all moni-
tors.
There are three slightly different displays possible:  Cold Start, Normal Start and Hot Start.
The Cold Start is the initial display seen when the Matrix Switcher is turned on for the first time.  The Normal Start is displayed if
the system has been shut off for two consecutive midnights (for example: the system is turned off Monday at 11:00 P.M. and...

97
5
OPERATING PROCEDURE
Before starting the following procedures, all system compo-
nents should be turned on.
Log-in
1. Turn on the power switches of all system components.
Caution:If the WJ-AD550 Extension Unit is used in the
system, turn the Extension Unit power on before
turning on the power of the WJ-SX550C Matrix
Switcher.
2. Turn on the power of the system controller by pressing
the Controller On/Off Switch located on the rear of the
System Controller to the ON position.
The following displays...

98
5
If an incorrect operator number or password is select-
ed, “No Entry” is displayed on the LCD display and the
Log-in procedure automatically returns to the start.“Monitor Busy” will appear on the LCD display when
another operator, with a higher operator priority, is cur-
rently controlling the monitor outputs.
The Log-in procedure automatically returns to the start.
‘No Entry‘
Log-in‘Monitor Busy‘
Log-in
Log-in
‘No Entry‘
Password    :.....
Welcome
‘Monitor Busy‘Operator No :
Password Error,...

99
5
 Operation Menus
After log-in, the following operation menus are available on the LCD display by pressing the appropriate Direction buttons.
For example, to go from the Camera/Monitor Selection Menu (A1) to the Shutter Selection Menu (C1), press the Bbutton
twice.
To go from the G-Seq Selection Menu to the Set Up Menu, press the Cbutton four times.
To actually set the Set Up Menu to the active or on mode, press the F1button while the Set Up Menu is displayed on the LCD
display.
Notes:
• Pressing...

Camera Selection
1. Select the desired camera number by pressing the
Numeric keys, then press the CAM (SET)key.
The selected camera picture appears on the active
monitor.
2. Press the INC +1CAM button to replace the currently
selected camera with the next higher camera number.
3. Press the DEC –1CAM button to replace the currently
selected camera with the next lower camera number.
Notes:
• “PROHIBITED” is displayed on the LCD display, if
control of the selected camera is disabled due to
limited operator...

101
5
Contrast and Backlight
Adjustment of LCD Display
The following procedure lets you adjust contrast and back-
light of the controllers LCD display.
Pressing the Direction (A, D, B) buttons at the same
time will display the following on the LCD display.
a) Contrast Adjustment
Pressing the ZOOM TELE/WIDEControl while holding
down the Direction (A, D, B) buttons at the same time
will adjust the contrast of the characters displayed on
the LCD display.
TELE: Increases the character contrast (00 →99)...

Pan/Tilt Control (Manual Operation)
1. Select the desired monitor and camera.
Refer to the Monitor Selection and Camera Selection on
page 100.
2. Select a mode by pressing the [F3]or [F4]button.
“❑” indicates the currently selected mode.
SLW:Moves the Pan/Tilt Head at lower speed.
FST:Moves the Pan/Tilt Head at higher speed.
Note:This function is available with the WV-CU550C
system controller.
3. Move the Joystick Controller to move the Pan/Tilt Head
in the desired direction.
If the joystick is...

103
5
Pan/Tilt Control (Home Position)
The following function requires the use of cameras
equipped with the specific feature.
1. Select the desired monitor and camera.
Refer to the Monitor Selection and Camera Selection.
2. Select the Cam-Preset (D1)Menu on the LCD display
by pressing the appropriate Direction button.
3. Press the Function (F1)button to move a camera to the
Home Position. 
Notes:
• Pressing the AUX 1 button while the ALT indicator
is on will move a camera to the home position with-
out...

5. Select the desired camera position number by pressing
the Numeric keys, then press the MON (ESC)key to
move the camera to the preset position.
The selected camera position appears on the active
monitor.
6. Press the Function (F4) button to return to the CAM-P
Menu.
Note: To to use the above functions, it is necessary to
register the preset position number with the cam-
era number.
Refer to the Mode Selection Switch Setting on
page 54 and the Camera Position Number Setting
on page 123 for further...

105
5
WV-CS604 Not available Not available
9
WV-CS854 WV-CS654
9
9Not available
Not availableNot available
Not available
WV-CS854A
9Not available Not available
WV-CS304
WV-CS404
9Not available Not available
WV-CS554
9Not available
Not available MODEL
*9 AUTO-PAN
Pan/Tilt Control (Auto/Random
Panning)
The functions described below require the use of the speci-
fied Pan/Tilt Head or camera equipped with the specific
feature.
WV-7220D
WV-7225 WV-BS204
WV-CS500
WV-7230D
WV-7260D*9*9
*9*9 9
9
9
*9
*9 Not...