Panasonic LCD Projector Pt Vx410 Operating Instructions

[COLOR TEMPERATURE]
You can switch the color temperature if the white areas of the projected \
image are bluish or reddish.
Press 1) as to select [COLOR TEMPERATURE].
Press 2) qw or the  button.
The [COLOR TEMPERATURE] individual adjustment screen is displayed. f
Press 3) qw to switch the item.
The items will switch each time you press the button. f
[DEFAULT]Factory default setting.
[HIGH]Selects the suitable natural color.[LOW]
[IRIS]
Aperture correction and signal compensation are performed...

Press 3) qw to switch the item.
The items will switch each time you press the button. f
[AUTO]Enables auto correction of [DAYLIGHT VIEW]. The luminance sensor detects the brightness and color of the surroundings and automatically corrects the video display.
[ON]Enables [DAYLIGHT VIEW].
[OFF]Disables [DAYLIGHT VIEW].
Note
[DAYLIGHT VIEW] can not be set to [AUTO] when the [PROJECTOR SETUP] menu → [PROJECTION METHOD] is set to  f
[REAR/DESK] or [REAR/CEILING].
The [AUTO] mode may not function properly if an...

[RGB/YPBPR]/[RGB/YCBCR]
Set it to [AUTO] normally. If images are not displayed correctly when this is set to [AUTO], set either [RGB] or [YCBCR], [YPBPR] in accordance with the input signal.
Press 1) as to select [RGB/YPBPR] or [RGB/YCBCR].
Press 2) qw or the  button.
The [RGB/YP fBPR] or [RGB/YCBCR] individual adjustment screen is displayed.
Press 3) qw to switch the item.
The items will switch each time you press the button. f
[AUTO]The sync signal automatically selects the signal [RGB]/...

[POSITION] menu
On the menu screen, select [POSITION] from the main menu, and select an \
item from the submenu.
Refer to "Navigating through the menu" (Æpage  45) for the operation of the menu screen.
After selecting the item, press  fasqw to set.
[REALTIME KEYSTONE]
The projector can correct the vertical trapezoidal distortion automatically when the projector is installed tilted.
Press 1) as to select [REALTIME KEYSTONE].
Press 2) qw or the  button.
[REALTIME KEYSTONE] individual adjustment...

ItemsOperationAdjustmentAdjustment range
[HORIZONTAL]
Press the w button.Adjusts the right of the keystone.
-60 ~ +60
Press the q button.Adjusts the left of the keystone.
[VERTICAL]
Press the a button.Adjusts the upper of the keystone.
-80 ~ +80
Press the s button.Adjusts the bottom of the keystone.
[CORNER CORRECTION]
Press 1) as to select [KEYSTONE].
Press the  button.2) 
The [KEYSTONE] screen is displayed. f
Press 3) as to select [CORNER CORRECTION].
Press the  button.4) 
The [CORNER CORRECTION]...

[SHIFT]
(Only for computer signal input)
Move the image position vertically or horizontally if the image position projected on the screen is shifted even when the relative 
position of the projector and the screen is installed correctly.
Press 1) as to select [SHIFT].
Press the  button.2) 
The [SHIFT] screen is displayed. f
Press 3) asqw to adjust the position.
OrientationOperationAdjustment
Vertical (up and down)
adjustment.
Press the a button.The image position moves up.
Press the s button.The image...

Note
Certain signals may not be adjustable. fOptimal value may not be achieved if the output from the input computer is unstable. fTo project a signal with dot clock frequency with 162 MHz or higher, noise may not disappear even if [CLOCK PHASE] is  fadjusted.[CLOCK PHASE] cannot be adjusted when a digital signal is input.  f
[OVER SCAN]
Use this function when characters or pictures are cropped near the perip\
hery of the projected image.
Press 1) as to select [OVER SCAN].
Press 2) qw or the  button.
The...

Note
The image size may be switched abnormally when [AUTO] is selected, please set to [NORMAL] or [WIDE] according to the  finput signal.Some size modes are not available for certain types of input signals.  fIf an aspect ratio which is different from the aspect ratio for the input signals is selected, the imag\
es will appear differently  ffrom the originals. Be careful of this when selecting the aspect ratio.If using the projector in places such as cafes or hotels to display prog\
rams for a commercial...

[LANGUAGE] menu
On the menu screen, select [LANGUAGE] from the main menu, and select an \
item from the submenu.
Refer to "Navigating through the menu" (Æpage 45) for the operation of the menu screen.
Press  fas to select a language, and press  button to set.
[LANGUAGE]
You can select the language of the on-screen display.
Various menus, settings, adjustment screens, control button names, etc., \
are displayed in the selected language. f
The language can be changed to English, German, French,...

[DISPLAY OPTION] menu 
On the menu screen, select [DISPLAY OPTION] from the main menu, and select an item from the submenu.
Refer to "Navigating through the menu" (Æpage 45) for the operation of the menu screen.
After selecting the item, press  fasqw to set.
[ON-SCREEN DISPLAY]
Set the on-screen display and position.
[INPUT GUIDE]
Set whether to display the input guide when switching the input source.
Press 1) as to select [ON-SCREEN DISPLAY].
Press the  button.2) 
The [ON-SCREEN DISPLAY] screen...