Panasonic LCD Projector Pt Vx410 Operating Instructions

[Old password]1 
Enter the current password.
[New password]2 
Enter the desired new password. (Up to 16 characters 
in single byte)
[Retype]3 
Enter the desired new password again.
[OK]4 
Determines the change of password.
Note
To change the account of the administrator, you must enter the [User name] and [Password] in [Current]. f
[Crestron Connected(TM)] page 
The projector can be monitored/controlled with Crestron Connected™.
To start the Crestron Connected™ control page from the web control screen,...

[Control System]1 
Set the information required for communicating with the
controller to be connected with the projector.
[User Password]2 
Set the user rights password for the Crestron 
Connected™ control page.
[Admin Password]3 
Set the administrator rights password for the Crestron 
Connected™ control page.
Network status4 Displays the settings of wired LAN.[DHCP]Displays the current setting.[Ip Address]Displays the current setting.[Subnet Mask]Displays the current setting.[Default Gateway]Displays...

Chapter 5   Maintenance
This chapter describes methods of inspection when there are problems, ma\
intenance, and 
replacements of the units.
ENGLISH - 93 

LAMP and WARNING Indicators
Managing the indicated problems
If a problem should occur inside the projector, the ,  and/or  indicators will inform 
you. Manage the indicated problems as follow.
Attention
Before you take a remedial measure, follow the procedure of switching the power off indicated in “Powering Off the  f
projector”. (Æpage 37)
LAMP indicator
IndicatorLighting in red.Flashing in red.
StatusTime to replace the lamp unit.A problem is detected in the lamp or the power supply for the 
lamp....

Replacement
Before performing maintenance/replacement
When you perform maintenance or replacement of the parts, make sure to t\
urn off the power and disconnect the power plug  ffrom the wall outlet. (Æ pages 34, 37)
Be sure to observe the procedure “ fPowering Off the projector” (Æ page 37) when performing power supply operation.
Maintenance
Outer Case
Wipe off dirt and dust using a soft dry cloth.
If the dirt is persistent, soak the cloth with water and wring it thorou\
ghly before wiping. Dry off the...

Attaching the air filter unit
Attach the unused air filter unit to the projector.1) 
Hold the air filter unit that the tab is in up-left side in the figure, put the right side in the figure first, and press the tab side  funtil make a click sound.
Do not press any other part of the air filter unit except the frame during installation. f
Install the air filter cover.2) 
Perform Step 1) in “Removing the air filter unit” ( fÆ page 95) in the reverse order .
Make sure that the air filter cover is closed...

Notes on the replacement of the lamp unit
The luminous source of the lamp is made of glass and may burst if you hi\
t it against a hard surface or drop it. Please handle  fwith care.A Phillips screwdriver is required for replacement of the lamp unit. fWhen replacing the lamp unit, be sure to hold it by the handle. fWhen replacing the lamp because it has stopped illuminating, there is a \
possibility that the lamp may be broken. If replacing  fthe lamp of a projector which has been installed on the...

Turn off the Power by following the procedure in "1) Powering Off the Projector" (Æ page 37). Remove 
the AC power plug from the wall outlet. Wait at least 1 hour and make sure the lamp unit and 
surroundings are cool. 
Remove the lamp cover. 2) 
Use a Phillips screwdriver to loosen the lamp cover fixing screw (×1\
) and remove the lamp cover.
Remove the lamp cover by pulling it slowly toward the direction of the a\
rrow. f
Remove the 3) lamp unit. 
Use a Phillips screwdriver to loosen the three...

Troubleshooting
Please check following points. For details, see the corresponding pages.
ProblemCauseReference 
page
Power does not turn on.
The power cord may not be connected. f
No electric supply is at the wall outlet. f
The circuit breakers have tripped. f
Is the  indicator or  indicator lit or blinking? f
The lamp cover has not been securely installed. f
—
—
—
35, 9497
No picture appears.
The video signal input source may not be connected to a terminal properl\
y. f
The input selection setting may...

Chapter 6   Appendix
This chapter describes specifications and after-sales service for the projector.
100 - ENGLISH