Panasonic LCD Projector Pt Vx410 Operating Instructions

Technical Information
PJLink protocol
The network function of the projector supports PJLink class 1, and the PJLink protocol can be used to perform projector setting 
and projector status query operations from a computer.
Control commands 
The following table lists the PJLink protocol commands that can be used to control the projector.
x characters in tables are non-specific characters. f
CommandControl detailsParameter / return stringRemark
POWRPower supply control01StandbyPower ON
POWR ?Power supply...

Control commands via LAN
When WEB Control administrator rights password is set (Protect mode)
Connection method 
Obtain the IP address and port number (Initial set value = 1 024) of the projector \
and make a request 1) 
for connection to the projector.
Acquire the IP address from the menu screen of the projector, and the port number from the WEB control page. f
IP address :Obtain from MAIN MENU → [NETWORK] → [STATUS]
Port No. :Acquire from the WEB control [Detailed set up] → [Port set up] page
There is...

When WEB Control administrator rights password is not set (Non-protect \
mode)
Connection method 
Obtain the IP address and port number (Initial set value = 1 024) of the projector \
and make a request 1) 
for connection to the projector.
Acquire the IP address from the menu screen of the projector, and the port number from the WEB control page. f
IP address :Obtain from main menu → [NETWORK] → [STATUS]
Port No. :Acquire from the WEB control [Detailed set up] → [Port set up] page
There is a response from...

Serial terminal
The serial connector which is on the connector panel of the projector conforms to the RS-232C interface specification, so that 
the projector can be controlled by a personal computer which is connecte\
d to this connector.
Connection
Connecting terminals  
      on projector
D-Sub 9-pin (female) Computer
D-Sub 9-pin (male) Communication cable (straight)
Pin assignments and signal names
D-Sub 9-pin (female)Outside viewPin No.Signal nameContents
—NC
TXDTransmitted data
RXDReceived data
—NC...

Basic format
Transmission from the computer begins with STX, then the command, parameter, and ETX are sent in this order. Add 
parameters according to the details of control.
STXAD I1I2 ;C1C2 C3 : P1 P2Pn ETX
When sending commands without parameters, a colon (:) is not necessary .* 
Basic format (with sub command)
S1S2S3S4S5 EP1P2P3P4P5P6
STX AD I1I2 ;C1C2C3 :  ETX
Same as basic format
Sub command (5 bytes) Operation (1 byte)
“=” (Value specified using parameter is set)Parameter (6 bytes)*
Symbol “+” or...

Cable specifications
[When connected to a computer] 
Projector
( terminal)
1NCNC1
Computer
(DTE specifications)
22334NCNC4556NCNC677889NCNC9
Control commands
When controlling the projector from a computer, the following commands are available:
Projector control command r
CommandControl contentsParameter / return stringRemarks
PONPower on―To check if the power is on, use the “Power 
query” command.POFPower off
IISINPUT selection
VID
SVD
RG1
RG2
HD1
VIDEO
S-VIDEO 
RGB1
RGB2
HDMI
OSHAV mute function0
1
AV...

Two window display combination list
Sub Window
COMPUTER1COMPUTER2
HDMIVIDEOS-VIDEO
Main WindowRGBYCBCR/YPBPRRGB
COMPUTER1RGB―――l――
YCBCR/YPBPR―――l――
COMPUTER2RGB―――l――
HDMIlll―ll
VIDEO―――l――
S-VIDEO―――l――
 l : Picture in Picture combinations are enabled.
 ―: Picture in Picture combinations are disabled.
Note
When setting the movie-based signal 1080/24p, 1080/24sF,1080/25p, 1080/30p, 1080/50p or 1080/60p for HDMI input, the  f
two window display function will be disabled.
The image of the sub window...

List of compatible signals
The following table specifies the type of signals compatible with the projectors.
Symbols that indicate formats are as follows.  fV = VIDEO, S = S-VIDEO, C = RGB, Y = YCBCR/YPBPR, H = HDMI
ModeDisplay resolution(dots)
Scanning frequencyDot clock frequency (MHz)Format*1PnP*2
H (kHz)V (Hz)COMPUTER1 /COMPUTER2HDMI
NTSC/NTSC4.43/
PAL-M/PAL60720 x 480i15.759.9―V/S――
PAL/PAL-N/SECAM720 x 576i15.650.0―V/S――
525i (480i)720 x 480i15.759.913.5C/Y――
625i (576i)720 x 576i15.650.013.5C/Y――...

ModeDisplay resolution(dots)
Scanning frequencyDot clock frequency (MHz)Format*1PnP*2
H (kHz)V (Hz)COMPUTER1 /COMPUTER2HDMI
1280 x 8001 280 x 80041.250.069.9C/H――
1 280 x 80049.760.084.7C/Hll
MSXGA1 280 x 96060.060.0108.0C/H――
SXGA
1 280 x 1 02464.060.0108.0C/Hll
1 280 x 1 02480.075.0135.0C/Hl―
1 280 x 1 02491.185.0157.5C/H――
1366 x 7681 366 x 76839.650.069.9C/H――
1 366 x 76847.760.084.7C/Hll
SXGA+1 400 x 1 05065.260.0122.6C/H――
1 400 x 1 05082.275.0155.9C/H――
WXGA+1 400 x 900*555.559.988.8C/H――
1600 x...

Specifications
Model No.PT-VW340ZPT-VX410Z
Power supplyAC100 V - 240 V, 50 Hz/60 Hz
Power consumption
100 V - 240 V, 3.5 A-1.3 A, 300 W
When [STANDBY MODE] of [PROJECTOR SETUP] is set to [ECO]: 0.4 W
When [STANDBY MODE] of [PROJECTOR SETUP] is set to [NORMAL]: 9 W
LCD 
panel
Panel size1.5 cm(0.59")
(aspect ratio 16 : 10)
1.6 cm(0.63")
(aspect ratio 4 : 3)
Display method3 transparent LCD panels (RGB)
Drive methodActive matrix method
Pixels1 024 000
(1 280 x 800) x 3 panels
786 432
(1 024 x 768) x...