Panasonic LCD Projector Pt Vx410 Operating Instructions

Description of each item 
1
2
3
4
5
6
Page tab1 Switches pages by clicking this item.
[Status]2 The status of the projector is displayed by clicking this item.
[Projector control]3 The [Projector control] page is displayed by clicking this item.
[Detailed set up]4 The [Detailed set up] page is displayed by clicking this item.
[Change password]5 The [Change password] page is displayed by clicking this item.
[Crestron Connected(TM)]6 The control page of Crestron Connected™ is displayed by clicking this...

Error information page 
When [Error (Detail)] or [Warning (Detail)] is displayed in the self-diagnosis display of the [Projector status] screen, click it to display the error/warning details.
The projector may go into the standby status to protect the projector de\
pending on the contents of the error. f
1
Self-diagnosis result display1 Displays the item check results.[OK]: Indicates that operation is normal.
[FAILED]: Indicates that there is a problem.[WARNING]: Indicates that there is a warning....

[Basic control] page 
Click [Projector control] → [Basic control].
1
2
5
6 3
4
[INPUT]1 Switches the input signal.
[VOLUME]2 Adjusts the volume level.
[PICTURE MODE]3 Switches the picture mode..
[AV MUTE]4 Switches between AV mute on/off.
[POWER]5 Turns on/off the power.
[CLOSED CAPTION]6 Switches the closed caption mode.
[Advanced control] page
Click [Projector control] → [Advanced control].
12
[POSITION]1 Adjusts the position of image and the keystone correction.
[PICTURE]2 Adjusts the items of image....

[Network config] page
Click [Detailed set up] → [Network config].
Click [Network config] to display the [CAUTION!] screen. f
The current settings are displayed by pressing the [Next] button. f
Click [Change] to display the setting change screen. f
2
7
1
345
6
[Projector name]1 Enter the name of the projector. Enter the host name if it is required when using a DHCP server etc.
[DHCP ON]/[DHCP OFF]2 To enable the DHCP client function, set to [DHCP ON].
[IP ADDRESS]3 Enter the IP address when not using a...

[Ping test] page
Check whether the network is connected to the mail server, POP server, DNS server, etc.
Click [Detailed set up] → [Ping test].
1
23
4
[Input IP address]1 Enter the IP address of the server to be tested.
[Submit]2 Executes the connection test.
Example of display when the connection has 3 succeeded
Example of display when the connection has failed4 
[E-mail set up] page 
When there is a problem or the runtime of a lamp reaches a set value, an E-mail can be sent to preset E-mail 
addresses...

8
7
9
8
7
[E-MAIL ADDRESS 1]/[E-MAIL ADDRESS 2]7 Enter the E-mail address to be sent. Leave [E-MAIL ADDRESS 2] blank when two E-mail addresses are not to be used.
Settings of the conditions to send E-mail8 Select the conditions to send E-mail. [MAIL CONTENTS]:Select either [NORMAL] or [SIMPLE].[ERROR]:Send an E-mail when an error occurred in the self-diagnosis.
[LAMP RUNTIME]:An E-mail message is sent when the remaining lamp on time for the lamp has reached the value set at the right field.[INTAKE AIR...

Contents of mail sent 
Example of E-mail sent when E-mail is set
Mail with the contents shown below is sent when the e-mail settings have\
 been established.
=== Panasonic projector report(CONFIGURE) ===
Projector Type          : PT-VW340Z
Serial No               : 000000000
-----  E-mail setup data -----
TEMPERATURE WARNING SETUP 
MINIMUM TIME            at [ 60] minutes interval 
INTAKE AIR TEMPERATURE  Over [ 32degC / 89degF ] 
ERROR                   [ OFF ] 
LAMP RUNTIME            [ OFF ]   at...

Example of E-mail sent for an error
Mail with the contents shown below is sent when an error has occurred.
=== Panasonic projector report(ERROR) ===
Projector Type          : PT-VW340Z
Serial No               : 000000000
-----  check system -----
FAN                           [   OK   ]
FAN (INTAKE)                  [   OK   ]
FAN (EXHAUST)                 [   OK   ]
FAN (LAMP)                    [   OK   ]
INTAKE AIR TEMPERATURE        [   OK   ]
EXHAUST AIR TEMPERATURE       [   OK   ]
OPTICS MODULE...

[ECO management set up] page
You can make settings for the ECO management function of the projector.
Click [Detailed set up] → [ECO management set up].
1
2
3
4
5
6
78
[LAMP POWER]1 Selects the [LAMP POWER] setting.
[AUTO POWER SAVE]2 Select [ON] to set [AMBIENT LIGHT DETECTION], [SIGNAL DETECTION], and [AV MUTE DETECTION].
[AMBIENT LIGHT DETECTION]3 Enable ([ON])/disable ([OFF]) the ambient light detection function. 
[SIGNAL DETECTION]4 Enable ([ON])/disable ([OFF]) the signal detection function.
[AV...

[Administrator] account
1
2
3
4
5
67
[Account : Administrator]1 Displays the account to change. 
[Current] [User name]2 Enter the user name before the change.
[Current] [Password]3 Enter the current password.
[New] [User name]4 Enter the desired new user name.  (Up to 16 characters in single byte)
[New] [Password]5 Enter the desired new password.  (Up to 16 characters in single byte)
[New] [Password (Retype]6 Enter the desired new password again.
[OK]7 Determines the change of password.
[User] account
1...