Panasonic LCD Projector Pt Vx410 Operating Instructions

Connecting example : AV equipment
For // terminals
Attention
Always use one of the following when connecting a VCR.  f
- A VCR with built-in time base corrector (TBC). 
- A time base corrector (TBC) between the projector and the VCR.
If nonstandard burst signals are connected, the image may be distorted. \
In such case, connect the time base corrector  f
(TBC) between the projector and the external devices.
Note
For an HDMI cable, use an HDMI High Speed cable that conforms to HDMI standards. If a cable...

Attention
When connecting the projector to a computer or an external device, use the power cord supplied with each device and  f
commercially available shielded cables.
Note
If you operate the projector using the computer with the resume feature (last memory), you may have to reset the resume  f
feature to operate the projector.
Connecting example : Audio
Note
If the [AUDIO IN SELECT] settings are incorrect, the projector may have malfunctions such as the absence of audio. f
When the  terminal is...

Chapter 3   Basic Operations
This chapter describes basic operations to start with.
ENGLISH - 33 

Powering on/off
Connecting the power cord
Make sure that the supplied power cord is securely fixed to the projector body to prevent it from being removed easily.
For details of power cord handling, refer to “Read this first!” (Æpage 5).
Attaching 
Check the shapes of the  terminal on the back of the projector bo\
dy and the power cord 1) 
connector and insert the plug completely in the correct direction (unti\
l you hear the side tabs click in 
place).
Removing
Turn off the projector, and then remove the...

ON(G)/STANDBY(R) indicator
The ON(G)/STANDBY(R) indicator informs you the status of the power. Confirm the status of the  
indicator before operating the projector.
ON(G)/STANDBY(R) indicator
Indicator statusStatus
OffThe power cord is unplugged.
Red
Lit
The power cord is plugged.
The [STANDBY MODE] is set to [ECO] when the projector is in standby mode and the 
cooling is completed. 
BlinkingThe power is switched off (in standby mode). The [STANDBY MODE] is set to [NETWORK].*1
The power is switched off...

Connect the power cord to the projector body.1) 
Connect the power plug to an outlet.2) 
The power indicator  lights or blinks, and the projector will enter the standby mode. f
Press the  button on the control panel or on the remote control. 
The power indicator  lights in green and the image is soon projected on the screen. f
Attention
Using the projector while the lens cap is attached may cause the device to heat up and result in a fire. f
Note
If the [PROJECTOR SETUP] menu  f→ [ECO...

Powering Off the Projector
                
1) 2)
1) 2)
2)
3)
2)
 
Press the  button on the control panel or on the remote control.
The following message appears. f
Press 2) qw to select [OK], and press the  button. 
OR 
Press the  button on the control panel or on the remote control again. 
Projection of the image will stop, and the power indicator  lights in orange. (The fan keeps  f
running.)
Wait until the  indicator lights/blinks in red/green.3) 
The projector enters standby mode when the power...

Projecting
Check the connections of the peripheral devices and connection of the power cord (Æpages 29-34) and switch on the power 
(Æpage 36) to start the projector. Select the image and adjust the state of the image.
Selecting the input signal
Select an input signal.
Press , , , ,  or  button \
on the remote control or 1) 
 button on the control panel.
The image of the signal being input in the selected terminal is projecte\
d. f
You can check the input source through [DETAILED] / [SIMPLE] under the...

Basic operations by using the remote control
Using the AUTO SETUP function
The automatic setup function can be used to automatically adjust the res\
olution, clock phase, and image position when 
analog RGB signals consisting of bitmap images such as computer signals \
are being input. Supplying images with bright 
white borders at the edges and high-contrast black and white characters \
is recommended when the system is in automatic 
adjustment mode.
Avoid supplying images that include halftones or...

Switching the input signal
You can switch the input signals to project.
 buttons
Press the ,, ,  or  button\
 on the remote 1) 
control.
This operation can be also performed using the  button on the control panel. f
Switch to Computer 1 input.
Switch to Computer 2 input. 
 Switch to HDMI input.
Switch to Video input. 
Switch to S-video input.
Using the FUNCTION button
Some operations in the menu can be assigned to the  button on the remote control so that it can be used as an 
easy shortcut button....