Panasonic LCD Projector Pt Vx410 Operating Instructions

Zoom ring (Back)1 
Adjust the zoom.
Control Panel and Indicators (2 Æpage 22)
Lamp cover (3 Æpage 97)
The lamp unit is located inside.
Projection Lens4 
Focus ring (Front)5 
Adjust the focus.
Remote control signal receiver6  
Air exhaust port7 
Speaker8 
 terminal 9 
Connect the supplied power cord.
Rear terminals (10 Æpage 22)
Air intake port / Air filter cover (11 Æpage 95) 
The air filter unit is inside.
Adjustable feet 12 
Adjust the projection angle.
Security Chain Hook 13 
Attaches a burglar...

Control panel and Indicators r
 rRear terminals
Attention
When a LAN cable is directly connected to the projector, the network connection must be made indoors. f
 terminal1 This is the terminal to input RGB or YPBPR/YCBCR signals.
 terminalThis is the terminal to input RGB signals or output the RGB/YCBCR/YPBPR signals to external monitor.
 terminal3 This is the terminal to input HDMI signals.
 terminal4 This is the LAN terminal to connect to the network.
 terminal5 This is the RS-232C compatible terminal...

Using the remote control
Inserting and Removing batteries
                       
Open the cover. (Fig. 1)1) 
Insert batteries and close the cover (Insert the 2) m side first.) (Fig. 2)
When removing the batteries, perform the steps in reverse order. f
Setting Remote control ID numbers
When you use the system with multiple projectors, you can operate all th\
e projectors simultaneously or each projector 
individually using single remote control, if unique ID number is assigne\
d to each projector.
After...

Chapter 2   Getting Started
This chapter describes things you need to do before using the projector \
such as the setup and 
connections.
24 - ENGLISH 

Setting up
Installation mode
There are four ways to set up the projector. Set the [PROJECTOR SETUP] menu → [PROJECTION METHOD] (x page 67) 
depending on the installation location. 
Mounting on the ceiling and projecting forwardSetting on a desk/floor and projecting from rear(Using the translucent screen)
Menu itemMethodMenu itemMethod
[PROJECTION METHOD][FRONT/CEILING][PROJECTION METHOD][REAR/DESK]
Mounting on the ceiling and projecting from rear(Using the translucent screen)Setting on a desk/floor and...

Screen size and throw distance
Refer to the screen size and projection distances to install the projector. Image size and image position can be adjusted in 
accordance with the screen size and screen position.
　　　　　　　　　
Projected image
SH
SW
SDSHScreen
L (LW/LT)
Screen L (LW/LT)
SW
H
L (LW/LT) *1Projection distance (m)
SHImage height (m)
SWImage width (m)
HDistance from the center of lens to the image lower end (m)
SDProjected image size (m)
LW : Minimum distance *1 LT : Maximum distance
Attention
Before...

For PT-VX410Z
All measurements below are approximate and may differ slightly from the actual measurements. (Unit: m)
Projection sizeFor 4:3 aspect ratioFor 16:9 aspect ratio
Screen diagonal (SD)
Minimum 
distance
(LW)
Maximum 
distance
(LT)
Height position (H)
Minimum 
distance
(LW)
Maximum 
distance
(LT)
Height position (H)
0.76 (30")0.7 1.1 0.0460.8 1.20.037
1.02 (40")0.9 1.5 0.0611.0 1.7 0.050
1.27 (50")1.2 1.9 0.0761.3 2.1 0.062
1.52 (60")1.4 2.3 0.0911.6 2.5 0.075
1.78 (70")1.7...

Adjusting adjustable feet
Lift the front of the projector and press the feet lock latches on both \
side of the projector.
Release the feet lock latches to lock the adjustable feet and rotate the\
 adjustable feet to a proper height and tilt.
You can turn the adjustable feet to extend them. You can turn them in the opposite direction to contract them.
(You can adjust the projection angle vertically.)
Feet lock latches
Attention
Heated air comes out of the air exhaust port while the lamp is lit. Do not...

Connecting
Before connecting to the projector
Before connecting, carefully read the operating instructions for the external device to be connected. f
Turn off the power switch of the devices before connecting cables. f
Take note of the following points before connecting the cables. Failure to do so may result in malfunctions. f
-  When connecting a cable to a device connected to the projector or the pr\
ojector itself, touch any nearby metallic objects to 
eliminate static electricity from your body...

 terminal pin assignments and signal names
Outside viewPin No.Signal namesPin No.Signal names
R/PR*1+5 V
G/Y*1GND
B/PB*1—
—DDC data
GNDHD/SYNC
GNDVD
GNDDDC clock
GND
*1: It is only for RGB signals when the terminal is used as the input terminal. 
 terminal pin assignments and signal names
Outside viewPin No.Signal namesPin No.Signal names
T.M.D.S data 2+T.M.D.S clock shield
T.M.D.S data 2 shieldT.M.D.S clock -
T.M.D.S data 2-CEC
T.M.D.S data 1+—
T.M.D.S data 1 shieldSCL
T.M.D.S data 1-SDA
T.M.D.S data...