Panasonic LCD Projector Pt Vw345NZ Operating Instructions

[AUTO SETUP SETTING]
Set the automatic execution of AUTO SETUP.
The screen display position or signal level can be adjusted automatically without pressing the  button on the 
remote control on each occasion if you input unregistered signals freque\
ntly at meetings, etc.
1) Press as to select [AUTO SETUP SETTING].
2) Press qw to switch the item.
 fThe items will switch each time you press the button.
[AUTO]Enables the auto setup function when switching signals.
[BUTTON]Enables the auto setup function...

 fThe items will switch each time you press the button.
[SXGA]Normal setting.
[SXGA +]Set this when the edge of the image is cropped.
[P-TIMER]
Set and operate the presentation timer function.
1) Press as to select [P-TIMER].
2) Press the  button.
 fThe [P-TIMER] screen is displayed.
[MODE]Switches the elapsed time between [COUNT UP] and [COUNT DOWN].
[TIMER]Sets the finish time of timer when [COUNT DOWN] is selected.
[START] / [STOP] /
[RESTART]Operates the timer.
[RESET]Resets the count....

[P IN P]
(Only for PT-VW345NZ)
Locate a separate, small sub screen in the main screen to project two im\
ages simultaneously.
1) Press as to select [P IN P].
2) Press the  button.
 fThe [P IN P] screen is displayed.
[MODE]
1) Press as to select [MODE].
2) Press qw to switch the item.
 fThe items will switch each time you press the button.
[OFF]P IN P function is disabled.
[SIDE BY SIDE]Sub screen is displayed at the side of the main screen.
[P IN P]Sub screen is displayed in the main screen.
[SUBPICTURE...

[PROJECTOR SETUP] menu
On the menu screen, select [PROJECTOR SETUP] from the main menu, and select an item from the submenu.
Refer to "Navigating through the menu" (Æpage 54) for the operation of the menu screen.
 fAfter selecting the item, press asqw to set.
[STATUS]
You can check the using status of the projector.
1) Press as to select [STATUS].
2) Press the  button.
 fThe [STATUS] screen is displayed.
[SIGNAL][NAME]Displays the name of input signal.
[FREQUENCY]Displays the scanning frequency...

3) Press as to select the [PROJECTOR ID].
 fSelect one from [ALL], and [1] to [6].
[ALL]Select when controlling projectors without specifying an ID number.
[1] - [6]Select when specifying an ID number to control individual projector.
4) Press the  button to set it.
 f[PROJECTOR ID] is set.
Note
 fThe ID number can be set to [ALL], or from [1] to [6]. fTo specify an ID number for individual control, the ID number of a remote\
 control must match the ID number of the projector. fWhen the ID number is set...

[LAMP POWER]
Switch the brightness of the lamp according to the operating environment\
 of the projector or the purpose.
1) Press as to select [LAMP POWER]. 
2) Press qw to switch the item.
 fThe items will switch each time you press the button.
[NORMAL]Select when high luminance is required.
[ECO1]Select when high luminance is not required.
[ECO2]Select when lower luminance than [ECO1] is required.
Note
 fSet it to [ECO1] rather than [NORMAL] when you want to reduce power consumption, extend the life of...

[READY]The countdown timer is displayed after 30 seconds without input signal. \
The projection lamp turns off and cools down when reaching the set time, meanwhile the projector is in\
 the power management mode. The projection lamp will be turned on if the input signal is reconnected\
 or any button is pressed.
[SHUT DOWN]The countdown timer is displayed after 30 seconds without input signal. \
The projection lamp is turned off and cooled down when reached the set time, then the projector enter in\
to...

[EZ570 SERIES]EZ570 series, EW630 series, EW530 series, EX600 series, EX500 series
[VW431D]VW431D series
4) Press the  button.
[FUNCTION BUTTON]
The function assigned to the  button of the remote control is displayed. You can also release the assigned 
setting.
Releasing assigned function to the  button
1) Press as to select [FUNCTION BUTTON].
2) Press the  button.
 fThe [FUNCTION BUTTON] screen is displayed.
3) Select [DISABLE], then press the  button.
4) When the confirmation message is displayed,...

[OFF]Disables audio output in the standby mode.
[ON]
Enables audio output in the standby mode when [STANDBY MODE] is set to [NORMAL]. At this 
time, press the  buttons on the remote control or qw buttons on the control panel 
to adjust the volume.
Note
 fAudio cannot be output during standby when [ECO MANAGEMENT] → [STANDBY MODE] is set to [ECO] or [NETWORK] 
(Æpage 77).
Setting audio input selection
Choose the audio input terminal for each input signal.
1) Press as to select [AUDIO SETTING].
2) Press...

[EASY SETTING]
You can set the operation when press the  button on the control panel. 
1) Press as to select [EASY SETTING].
2) Press the  button.
 fThe [EASY SETTING] screen is displayed.
3) Press as to select [FOCUS ASSIST], [SCREEN FIT] or [COLORBOARD].
[FOCUS ASSIST]The level of focus adjustment is displayed in the color and length of th\
e bar. It is supported the 
manual adjustment through rotating the focus ring.
[SCREEN FIT]If it detects a screen frame, the projected image is corrected to fit the...