Panasonic LCD Projector Pt Vw345NZ Operating Instructions

Displaying the memory viewer screen
1) Press the  button on the remote control.
 fThe folder list and the thumbnail are displayed in the following menu.
 fPress the  button on the remote control or the  button on the 
control panel, the folder list and thumbnail will change.
 
 
Playing the pictures
When [AUTOPLAY] is set to [OFF]
It will display a picture when play the picture manually every time.
1) Press asqw to select a file.
2) Press the  button.
 fThe picture will display on the full screen.
3)...

3) Press the  button on the remote control or the  button on the control panel. 
 fReturn to the thumbnail or folder list screen.
Note
 fThe panel resolution is less than the picture, it will be enlarged when \
maintaining the aspect ratio. fThe panel resolution is more than the picture, it will be reduced when m\
aintaining the aspect ratio.
Playing the video
 
When [AUTOPLAY] is set to [OFF]
It will play a video file every time.
1) Press asqw to select a file.
2) Press the  button.
 fPlaying on the...

Description of the memory viewer screen
The indication of icons on the memory viewer screen are as following:
 
 
 
  
 
 
 
 
 
 
Icon indicates that can move to the upper layer. Move to the upper layer when selected.
 
 
 
  
 
 
 
 
 
 Icon indicates the lower layer of the folder. Move to the lower layer when selected.
 
 
 
 
 
 
 
 
 
 
 
 
 
Icon indicates that the file is a picture.
 
 
 
 
 
 
 
 
 
 
 
 
 
Icon indicates that the file is a video.
 
 
 
 
 
 
 
 
 
    
Icon indicates that the...

Chapter 5   Maintenance
This chapter describes methods of inspection when there are problems, ma\
intenance, and 
replacement of the units.
114 - ENGLISH  

LAMP and WARNING Indicators
When an indicator lights up
If a problem should occur inside the projector, the  and/or  indicators will inform you. Manage the 
indicated problems as follow.
Attention
 fBefore you take a remedial measure, follow the procedure of switching the power off indicated in “Powering Off the 
projector”. (Æ page 43)
LAMP indicator
Indicator statusLighting in redBlinking in red
StatusTime to replace the lamp unit.  
(Æ page 118)
A problem is detected in the lamp or the power supply...

Replacement
Before performing maintenance/replacement
 fWhen you perform maintenance or replacement of the parts, make sure to turn off the power and disconnect the power plug 
from the wall outlet. (Æ pages 43, 40)
 fBe sure to observe the procedure “Powering Off the projector” (Æ page 43) when performing power supply operation.
Maintenance
Outer Case
Wipe off dirt and dust using a soft dry cloth.
 fIf the dirt is persistent, soak the cloth with water and wring it thorou\
ghly before wiping. Dry off the...

Attaching the air filter unit
1) Attach the unused air filter unit to the projector.
 fHold the air filter unit that the tab is in up-left side in the figure, put the right side in the figure first, and press the tab side 
until make a click sound.
 fDo not press any other part of the air filter unit except the frame during installation.
2) Install the air filter cover.
 fPerform Step 1) in “Removing the air filter unit” (Æ page 116) in the reverse order.
 fMake sure that the air filter cover is closed...

Notes on the replacement of the lamp unit
 fThe luminous source of the lamp is made of glass and may burst if you hi\
t it against a hard surface or drop it.  Please handle with care. fA Phillips screwdriver is required for replacement of the lamp unit. fWhen replacing the lamp unit, be sure to hold it by the handle. fWhen replacing the lamp because it has stopped illuminating, there is a possibility that the lamp may be broken. If replacing the lamp of a projector which has been installed on the...

Attaching the Lens Cap
When moving this projector or while not using it over an extended period of time, attach the lens cap.
To prevent loss for the lens cap, please according to the following proce\
dures, attach the lens cap  with the string of 
accessories. 
1) Thread the thinner end of the string through the hole on the lens cap.
2) Thread the other end of the string through the hole on the bottom of the\
 projector.
 
Lens cap
String
1) Turn off the Power by following the procedure in "Powering...

Troubleshooting
Please check following points. For details, see the corresponding pages.
ProblemCauseReference 
page
Power does not turn on.
 fThe power cord may not be connected.
 fNo electric supply is at the wall outlet.
 fThe circuit breakers have tripped.
 fIs the  indicator or  indicator lit or blinking?
 fThe lamp cover has not been securely installed.
—
—
—
11 5
11 8
No picture appears.
 fThe video signal input source may not be connected to a terminal properl\
y.
 fThe input selection setting...