Panasonic LCD Projector Pt Vw345NZ Operating Instructions

[Ping test] page
Check whether the network is connected to the mail server, POP server, DNS server, etc.
Click [Detailed set up] → [Ping test].
1
23
4
1 [Input IP address]Enter the IP address of the server to be tested.
2 [Submit]Executes the connection test.
3 Example of display when the connection has succeeded
4 Example of display when the connection has failed
[E-mail set up] page 
When there is a problem or the runtime of a lamp reaches a set value, an E-mail can be sent to preset E-mail 
addresses...

8
7
9
8
7
7 [E-MAIL ADDRESS 1]/[E-MAIL ADDRESS 2]Enter the E-mail address to be sent. Leave [E-MAIL ADDRESS 2] blank when two E-mail addresses are not to be used.
8 Settings of the conditions to send E-mailSelect the conditions to send E-mail. 
[MAIL CONTENTS]:Select either [NORMAL] or [SIMPLE].[ERROR]:Send an E-mail when an error occurred in the self-diagnosis.
[LAMP RUNTIME]:An E-mail message is sent when the remaining lamp on time for the lamp has reached the value set at the right field.[INTAKE AIR...

Contents of mail sent 
Example of E-mail sent when E-mail is set
Mail with the contents shown below is sent when the e-mail settings have been established.
=== Panasonic projector report(CONFIGURE) ===
Projector Ty pe          : PT-V W345N
Serial No               : 000000000
-----  E-m ail setup d ata -----
TEMPER ATURE WARNING SETUP 
MINIMUM TIME            at [ 60] minutes interval 
INTAKE AIR TEMPER ATURE  Over [ 32degC / 89degF ] 
ERROR                   [ OFF ] 
LA MP RUNTIME      
      [ OFF ]...

Example of E-mail sent for an error
Mail with the contents shown below is sent when an error has occurred.
=== Panasonic projector report(ERROR) ===
Projector Ty pe          : PT-V W345N
Serial No               : 000000000
-----  check syste m -----
FAN                           [   OK   ]
FAN (INTAKE)                  [   OK   ]
FAN (EXHAUST)                 [   OK   ]
FAN (LA MP)                    [   OK   ]
INTAKE AIR TEMPER ATURE 
       [   OK   ]
EXHAUST AIR TEMPER ATURE       [   OK   ]
OPTICS...

[ECO management set up] page
You can make settings for the ECO management function of the projector.
Click [Detailed set up] → [ECO management set up].
1
2
3
4
5
6
78
1 [LAMP POWER]Selects the [LAMP POWER] setting.
2 [AUTO POWER SAVE]Select [ON] to set [AMBIENT LIGHT DETECTION], [SIGNAL DETECTION], and [AV MUTE DETECTION].
3 [AMBIENT LIGHT DETECTION]Enable ([ON])/disable ([OFF]) the ambient light detection function. 
4 [SIGNAL DETECTION]Enable ([ON])/disable ([OFF]) the signal detection function.
5 [AV...

[Administrator] account
1
2
3
4
5
6
7
1 [Account : Administrator]
Displays the account to change. 
2 [Current] [User name]
Enter the user name before the change.
3 [Current] [Password]
Enter the current password.
4 [New] [User name]
Enter the desired new user name.  
(Up to 16 characters in single byte)
5 [New] [Password]
Enter the desired new password.  
(Up to 16 characters in single byte)
6 [New] [Password (Retype)]
Enter the desired new password again.
7 [OK]
Determines the change of password.
[User]...

[Change Password] (For user rights)
Only the change of password is enabled under the user rights.
1
2
4 3
1 [Old password]
Enter the current password.
2 [New password]
Enter the desired new password. (Up to 16 characters 
in single byte)
3 [Retype]
Enter the desired new password again.
4 [OK]
Determines the change of password.
Note
 fTo change the account of the administrator, you must enter the [User name] and [Password] in [Current].
[Crestron Connected(TM)] page 
The projector can be...

[Tools] page
Click [Tools] on the control page.
1
2
3
4
5
1 [Control System]
Set the information required for communicating with the 
controller to be connected with the projector.
2 [User Password]
Set the user rights password for the Crestron 
Connected™ control page.
3 [Admin Password]
Set the administrator rights password for the Crestron 
Connected™ control page.
4 Network statusDisplays the settings of wired LAN.
[DHCP]Displays the current setting.[IpAddress]Displays the current...

[Help] page
Click [Help] on the control page.
The [Help Desk] window is displayed.
1
1 [Help Desk]Send/receive messages to/from an administrator who uses Crestron Connected™.
ENGLISH - 109
Chapter 4   Settings - [SECURITY] menu  

Memory Viewer function
The Memory Viewer function makes it is possible to project the video and pictures which are stored in the USB 
memory when the USB memory is inserted into the projector.
 rWhat you can project with the Memory Viewer function
Memory Viewer function supports the following files.
Video
ExtensionVideo codecAudio codecVideo formatAudio format
movH.264/AVC
MotionJpeg
AAC
AC-3
Linear PCM
Maximum:
1 920 x 1 080/30 fps 
Maximum:
48 kHz 2 ch
(It is up to 16 kHz 
stereo when the codec 
is...