Panasonic LCD Projector Pt Vw345NZ Operating Instructions

							[AUTO SETUP SETTING]
Set the automatic execution of AUTO SETUP.
The screen display position or signal level can be adjusted automatically without pressing the  button on the 
remote control on each occasion if you input unregistered signals freque\
ntly at meetings, etc.
1) Press as to select [AUTO SETUP SETTING].
2) Press qw to switch the item.
 fThe items will switch each time you press the button.
[AUTO]Enables the auto setup function when switching signals.
[BUTTON]Enables the auto setup function only when the  button is pressed.
[SIGNAL SEARCH]
When the power is turned on, this function automatically detects the terminal which signals are input and sets the function to switch.
1) Press as to select [SIGNAL SEARCH].
2) Press qw to switch the item.
 fThe items will switch each time you press the button.
[ON]Enables input detection automatically.
[OFF]Disables input detection automatically.
Note
 fIf the [SIGNAL SEARCH] is set to [ON] when there is no signal input, press the  button on the remote 
control, this function automatically detects the terminal to which signa\
ls are input and then switches.
[BACK COLOR]
Set the display of the projected screen when there is no signal input. 
1) Press as to select [BACK COLOR].
2) Press qw to switch the item.
 fThe items will switch each time you press the button.
[BLUE]Displays the entire projection area in blue.
[BLACK]Displays the entire projection area in black.
[DEFAULT LOGO]Displays the Panasonic logo.
[USER LOGO]Displays the image registered by the user.
Note
 fTo create/register the [USER LOGO] image, use “Logo Transfer Software” included in the supplied CD-ROM. fIf you do not register the image of the [USER LOGO], the projected image will be displayed in black even if the [BACK 
COLOR] is set to [USER LOGO]. 
[WIDE MODE]
Using this function when displays the incorrect signals input.
1) Press as to select [WIDE MODE].
2) Press qw to switch the item.
 fThe items will switch each time you press the button.
[AUTO]Displays by judging the signal automatically. Set to this mode normally.
[OFF]When input the 4:3 signal.
[ON]When input the wide signal.
[SXGA MODE]
This function is used if the whole projected image is not displayed when SXGA signal is input. Set it to [SXGA] normally.
1) Press as to select [SXGA MODE].
2) Press qw to switch the item.
ENGLISH - 71
Chapter 4   Settings - [DISPLAY OPTION] menu   
						

							 fThe items will switch each time you press the button.
[SXGA]Normal setting.
[SXGA +]Set this when the edge of the image is cropped.
[P-TIMER]
Set and operate the presentation timer function.
1) Press as to select [P-TIMER].
2) Press the  button.
 fThe [P-TIMER] screen is displayed.
[MODE]Switches the elapsed time between [COUNT UP] and [COUNT DOWN].
[TIMER]Sets the finish time of timer when [COUNT DOWN] is selected.
[START] / [STOP] /
[RESTART]Operates the timer.
[RESET]Resets the count.
[EXIT][P-TIMER] is finished.
Setting [MODE]
1) Press as to select [MODE].
2) Press qw to switch the item.
 fThe items will switch each time you press the button.
[COUNT UP]Displays the elapsed time from count started.
[COUNT DOWN]Displays the remaining time for the time set in [TIMER] menu.
Setting the countdown timer
1) Press as to select [TIMER].
2) Press qw to set the timer.
 fThe timer can be set from 1 to 180 minutes in 1 increment.
 fThe factory default setting is 10 minutes.
Note
 f[TIMER] is available only when [MODE] is set to [COUNT DOWN].
The operation of [P-TIMER]
1) Press as to select [START], [STOP] or [RESTART].
[START]Starts counting.
[STOP]Stops counting.
[RESTART]Restarts counting.
2) Press the  button.
 fWhen you select [START] or [RESTART], the remaining time or the elapsed time will be displayed in the lower right of the projected image.
 fWhen you select [STOP], the remaining time or the elapsed time while stopping the counting will be displayed in the lower right of the projected image.
 fWhen [RESET] is selected, then go to step 3).
3) Press the  button 3 times and then the menu screen will disappear.
 fThe start time will be displayed in the lower right of the projected ima\
ge.
Note
 fYou can also use the P-TIMER function by pressing the  button on the remote control (Æpage 52).
 fIf the elapsed time or remaining time is displaying, the text will not be displayed even when the [SECURITY] menu → [TEXT 
DISPLAY] (Æ page 83) is set to [ON].
 fThe elapsed time or remaining time will not be display when the Menu scr\
een is displaying.
 fThe start time will be "000:00" when [MODE] is set to [COUNT UP].
 fThe start time will change to the time which is set in [TIMER] when [MODE] is set to [COUNT DOWN].
 fThe circle gauge for [COUNT UP] is rotated clockwise, the circle gauge for [COUNT DOWN] is rotated counter-clockwise.
72 - ENGLISH
Chapter 4   Settings - [DISPLAY OPTION] menu   
						

							[P IN P]
(Only for PT-VW345NZ)
Locate a separate, small sub screen in the main screen to project two im\
ages simultaneously.
1) Press as to select [P IN P].
2) Press the  button.
 fThe [P IN P] screen is displayed.
[MODE]
1) Press as to select [MODE].
2) Press qw to switch the item.
 fThe items will switch each time you press the button.
[OFF]P IN P function is disabled.
[SIDE BY SIDE]Sub screen is displayed at the side of the main screen.
[P IN P]Sub screen is displayed in the main screen.
[SUBPICTURE SIZE]
If [MODE] is set to [P IN P], you can change the size of the sub screen.
1) Press as to select [SUBPICTURE SIZE].
2) Press qw to switch the item.
 fThe items will switch each time you press the button.
[SMALL]The size of the sub screen is small (30% of the panel resolution).
[MIDDLE]The size of the sub screen is middle (40% of the panel resolution).
[LARGE]The size of the sub screen is large (50% of the panel resolution).
[SUBPICTURE POSITION]
If [MODE] is set to [P IN P], you can change the position of the sub screen.
1) Press as to select [SUBPICTURE POSITION].
2) Press qw to switch the item.
 fThe items will switch each time you press the button as following: 
[LOWER RIGHT] → [LOWER LEFT] → [UPPER LEFT] →[ UPPER RIGHT] → [LOWER RIGHT] →...
Note
 fThe P IN P function may be unavailable for some signals being input or terminals being selected. Refer to “Two-window 
display combination list” (Æpage 129) for details.
 fThe main window setting values are applied to image adjustment values such as [PICTURE MODE] and [COLOR 
TEMPERATURE].
[OTHER FUNCTIONS]
You can perform some of the remote control button operations instead of m\
enu operations.
1) Press as to select [OTHER FUNCTIONS].
2) Press the  button.
 fThe [OTHER FUNCTIONS] screen is displayed.
3) Press as to select [AUTO SETUP], [FREEZE], [AV MUTE] or [DIGITAL ZOOM].
[AUTO SETUP]For details, refer to "Using the AUTO SETUP function" (Æpage 47).
[FREEZE]
The projected image is paused temporarily and the sound stopped regardle\
ss of the playback of 
the external equipment. To release this function, press the  button or the  
button on the remote control.
[AV MUTE]Turn off audio and image when the projector is not used for a certain period of\
 time. To release 
this function, press the  button or the  button on the remote control.
[DIGITAL ZOOM]For details, refer to "Using the DIGITAL ZOOM function" (Æpage 50).
4) Press the  button.
ENGLISH - 73
Chapter 4   Settings - [DISPLAY OPTION] menu   
						

							[PROJECTOR SETUP] menu
On the menu screen, select [PROJECTOR SETUP] from the main menu, and select an item from the submenu.
Refer to "Navigating through the menu" (Æpage 54) for the operation of the menu screen.
 fAfter selecting the item, press asqw to set.
[STATUS]
You can check the using status of the projector.
1) Press as to select [STATUS].
2) Press the  button.
 fThe [STATUS] screen is displayed.
[SIGNAL][NAME]Displays the name of input signal.
[FREQUENCY]Displays the scanning frequency of input signal.
[RUNTIME]*1
[PROJECTOR]Displays the current usage time of projector.
[LAMP  
(ET-)]
[NORMAL]
[ECO1]
[ECO2]
Displays the operation time of lamp in each mode (NORMAL/
ECO1/ECO2). It may differ from the actual runtime under the 
each setting of [NORMAL]/[ECO1]/[ECO2] in [LAMP POWER] 
menu. And, displays the model no. of the replacement lamp unit 
for this projector.
[SERIAL NUMBER][PROJECTOR]Displays the serial number of the projector.
*1 The following conversion is required to calculate the rough estimate for\
 lamp replacement.
Formula for lamp replacement time (rough estimate)
A ×1 + B × 0.8 + C × 2/3
 fA : Runtime which is displayed in [STATUS] screen - [RUNTIME] - [LAMP] - [NORMAL] 
 fB : Runtime which is displayed in [STATUS] screen - [RUNTIME] - [LAMP] - [ECO1] 
 fC : Runtime which is displayed in [STATUS] screen - [RUNTIME] - [LAMP] - [ECO2] 
[COMPUTER2 SELECT]
Set whether to use the  terminal.
1) Press as to select [COMPUTER2 SELECT].
2) Press qw to switch the item.
 fThe items will switch each time you press the button.
[COMPUTER2 IN]When input the computer signal.
[COMPUTER1 OUT]Outputs the signal which have been input  terminal.
Note
 fThe [COMPUTER2 SELECT] will be unavailable when COMPUTER2 is selected as input source.
[PROJECTOR ID]
The projector has an ID number setting function that can be used when mu\
ltiple projectors are used side by side to enable 
simultaneous control or individual control via a single remote control.
1) Press as to select [PROJECTOR ID].
2) Press the  button.
 fThe [PROJECTOR ID] screen is displayed.
74 - ENGLISH
Chapter 4   Settings - [PROJECTOR SETUP] menu  
						

							3) Press as to select the [PROJECTOR ID].
 fSelect one from [ALL], and [1] to [6].
[ALL]Select when controlling projectors without specifying an ID number.
[1] - [6]Select when specifying an ID number to control individual projector.
4) Press the  button to set it.
 f[PROJECTOR ID] is set.
Note
 fThe ID number can be set to [ALL], or from [1] to [6]. fTo specify an ID number for individual control, the ID number of a remote\
 control must match the ID number of the projector. fWhen the ID number is set to [ALL], the projector will operate regardless of the ID number specified during remote control or computer control.  If multiple projectors are set up side by side with ID set to [ALL], they cannot be controlled separately from the projectors with other ID numbers. fRefer to “Setting the remote control ID numbers” (Æpage 29) for how to set the ID number on the remote control.
[INITIAL START UP]
Set the method of start up when the power cord plugged into the AC outlet.
1) Press as to select [INITIAL START UP].
2) Press qw to switch the item.
 fThe items will switch each time you press the button.
[LAST MEMORY]Starts in the condition that before disconnected the power cord or turn \
off the breaker. 
[STANDBY]Starts up in the standby mode.
[ON]Starts the projection immediately.
[PROJECTION METHOD]
Set the projection method in accordance with the installation status of \
the projector.
Change the projection method if the screen display is upside down or inv\
erted.
1) Press as to select [PROJECTION METHOD].
2) Press qw to switch the item.
 fThe items will switch each time you press the button.
[FRONT/DESK]When installing the projector on the desk, etc. in front of the screen.
[FRONT/CEILING]When installing the projector in front of the screen by using the Ceiling Mount Bracket for 
Projectors (optional).
[REAR/DESK]When installing the projector on the desk, etc. behind the screen (with a translucent screen).
[REAR/CEILING]When installing the projector behind the screen (with a translucent screen) by using the Ceiling 
Mount Bracket for Projectors (optional).
[HIGH ALTITUDE MODE]
Change the setting according to the altitude in which you use the projec\
tor.
1) Press as to select [HIGH ALTITUDE MODE].
2) Press qw to switch the item.
 fThe items will switch each time you press the button.
[OFF]When using the projector in the elevation of below 1 400 m.
[HIGH1]When using the projector in the elevation of above 1 400 m and below 2 000 m.
[HIGH2]When using the projector in the elevation of above 2 000 m and below 2 700 m.
Note
 fIt is set to [OFF] when using the projector in the elevation of below 1 400 m. It is set to [HIGH1] when using the projector in the elevation of above 1 400 m and below 2 000 m. It is set to [HIGH2] when using the projector in the elevation of above  2 000 m and below 2 700 m. Failure to do so may shorten the life of the internal parts and result in malfunctions.
 fDo not set the projector in the elevation of 2 700 m or above, otherwise\
 it may shorten the life of the internal parts and result in malfunctions. fWhen it is set to [HIGH1] or [HIGH2], the fan noise becomes louder and fan speed increases. 
ENGLISH - 75
Chapter 4   Settings - [PROJECTOR SETUP] menu  
						

							[LAMP POWER]
Switch the brightness of the lamp according to the operating environment\
 of the projector or the purpose.
1) Press as to select [LAMP POWER]. 
2) Press qw to switch the item.
 fThe items will switch each time you press the button.
[NORMAL]Select when high luminance is required.
[ECO1]Select when high luminance is not required.
[ECO2]Select when lower luminance than [ECO1] is required.
Note
 fSet it to [ECO1] rather than [NORMAL] when you want to reduce power consumption, extend the life of lamp and reduce 
operation noise.
 fSet it to [ECO2] rather than [ECO1] when you want to reduce power consumption and extend the life of lamp.
[ECO MANAGEMENT]
This function optimizes lamp power according to the operating status to reduce power consumption.
1) Press as to select [ECO MANAGEMENT].
2) Press the  button.
 fThe [ECO MANAGEMENT] screen is displayed.
3) Press as to select one item.
Setting [AUTO POWER SAVE] in step 3)
Set whether or not to enable the three functions, [AMBIENT LIGHT DETECTION], [SIGNAL DETECTION] and [AV MUTE 
DETECTION].
Note
 f[AUTO POWER SAVE] cannot be set when the [LAMP POWER] is set to [ECO2].
4) Press qw to switch the [AUTO POWER SAVE].
[ON]Enables power-saving mode.
[OFF]Disables power-saving mode.
5) Press as to select one item.
[AMBIENT LIGHT DETECTION]Adjusts the lamp power according to the ambient brightness.
[SIGNAL DETECTION]Drops the lamp power when no signal is input.
[AV MUTE DETECTION]Drops the lamp power in the AV mute mode.
6) Press qw to switch the item.
 fThe items will switch each time you press the button.
[ON]Enables above setting.
[OFF]Disables above setting.
Note
 fLamp power cannot reduced automatically in the following cases: 
- When [LAMP POWER] is set to [ECO2]. 
- When the lamp lit or the setting of [LAMP POWER] is completed, etc..
 fWhen [AUTO POWER SAVE] is set to [OFF], [AMBIENT LIGHT DETECTION], [SIGNAL DETECTION] and [AV MUTE 
DETECTION] cannot be set.
 f[AMBIENT LIGHT DETECTION] will not work correctly when placing some objects on the ambient luminance sensor.
Setting [POWER MANAGEMENT] in step 3)
Set the operation as following if there is no signal input.
1) Press as to select [POWER MANAGEMENT].
2) Press qw to switch the item.
 fThe items will switch each time you press the button.
76 - ENGLISH
Chapter 4   Settings - [PROJECTOR SETUP] menu  
						

							[READY]The countdown timer is displayed after 30 seconds without input signal. \
The projection lamp turns off and cools down when reaching the set time, meanwhile the projector is in\
 the power management mode. The projection lamp will be turned on if the input signal is reconnected\
 or any button is pressed.
[SHUT DOWN]The countdown timer is displayed after 30 seconds without input signal. \
The projection lamp is turned off and cooled down when reached the set time, then the projector enter in\
to standby status.
[OFF]Power management function is off.
Setting [TIMER]
The timer can be set to 5-120 minutes. The increment is 5 minutes.
1) Press as to select [TIMER].
2) Press qw to set the timer (5-120 MIN.).
 fThe time will switch each time you press the button.
Setting [STANDBY MODE] in step 3)
Set the power consumption during standby.
1) Press as to select [STANDBY MODE].
2) Press qw to switch the item.
 fThe items will switch each time you press the button.
[ECO]Restricts some functions in the standby mode to reduce power consumption\
.
[NETWORK]Restricts network function in the standby mode.  
[NORMAL]Does not restrict network function and serial communication function eve\
n in the standby mode.
Note
 fIf [STANDBY MODE] is set to [ECO], you cannot use network functions when the projector is standing by. Also, you cannot use some RS-232C protocol commands. fWhen set to [ECO], it may take approx. 10 seconds longer before the projector starts projecting after the power is turned on, compared with when [NORMAL] is set. fIf [STANDBY MODE] is set to [NETWORK], it takes less power consumption than it is set to [NORMAL]. fWhen [STANDBY MODE] is set to [NETWORK], it will be no restriction for network function and serial communication function within 60 seconds when the Wake on LAN function is working. fThe setting of [STANDBY MODE] cannot be returned to the factory default even if the [PROJECTOR SETUP] menu → 
[INITIALIZE ALL] is executed (Æpage 81).
[EMULATE]
When controlling the projector on a computer via the  terminal, set use of control commands on a previously purchased Panasonic projector. This allows the control software for an existing Panasonic projector to be inherited and used. 
1) Press as to select [EMULATE].
2) Press the  button.
 fThe [EMULATE] screen is displayed.
3) Press as to switch the item.
 fThe items will switch each time you press the button.
[DEFAULT]VW345N series, VX415N series, VW340Z, VX410Z, VX42Z, RZ475 series, RZ470 series, RW430 
series, RZ370 series, RW330 series
[D3500]D3500 series
[D4000]D4000 series
[D/W5k SERIES]D5700 series, DW5100 series, D5600 series, DW5000 series, D5500 series
[D/W/Z6k SERIES]
DZ770 series, DW740 series, DX810 series, DZ680 series, DW640 series, DX610 series,  
DW730 series, DX800 series, DZ6710 series, DZ6700 series, DW6300 series, D6000 series, 
D5000 series, DZ570 series, DW530 series, DX500 series
[L730 SERIES]L730 series, L720 series, L520 series
[L780 SERIES]L780 series, L750 series
[L735 SERIES]L735 series
[L785 SERIES]L785 series
[F/W SERIES]FW430 series, FX400 series, FW300 series, F300 series, F200 series, FW100 series, F100 series
[LZ370]LZ370 series
[LB/W SERIES]LB3 series, LB2 series, LB1 series, ST10 series, LB90 series, LW80NT series, LB80 series,  
LB78 series, LB75 series
[VX500 SERIES]VW435N series, VW440 series, VW430 series, VX505N series, VX510 series, VX500 series, 
VW330 series, VX400NT series, VX400 series, VX41 series
ENGLISH - 77
Chapter 4   Settings - [PROJECTOR SETUP] menu  
						

							[EZ570 SERIES]EZ570 series, EW630 series, EW530 series, EX600 series, EX500 series
[VW431D]VW431D series
4) Press the  button.
[FUNCTION BUTTON]
The function assigned to the  button of the remote control is displayed. You can also release the assigned 
setting.
Releasing assigned function to the  button
1) Press as to select [FUNCTION BUTTON].
2) Press the  button.
 fThe [FUNCTION BUTTON] screen is displayed.
3) Select [DISABLE], then press the  button.
4) When the confirmation message is displayed, select [OK] and press the  button.
Note
 fYou can also cancel the assigned settings by displaying the on-screen menu, selecting the menu item to be canceled (main 
menu, submenu, or details menu), and then pressing the  button for at least 3 seconds.
[AUDIO SETTING]
You can perform more detailed setting for Audio.
Adjusting the volume
1) Press as to select [AUDIO SETTING].
2) Press the  button.
 fThe [AUDIO SETTING] screen is displayed.
3) Press as to select [VOLUME].
4) Press qw to adjust the level.
OperationAdjustmentRange
Press the w button.Turns up the volume.0 ~ 63Press the q button.Turns down the volume.
Setting the mute
1) Press as to select [AUDIO SETTING].
2) Press the  button.
 fThe [AUDIO SETTING] screen is displayed.
3) Press as to select [MUTE].
4) Press qw to switch the item.
[ON]Turns off the volume temporarily.
[OFF]Output the audio.
Setting the audio output during standby
1) Press as to select [AUDIO SETTING].
2) Press the  button.
 fThe [AUDIO SETTING] screen is displayed.
3) Press as to select [IN STANDBY MODE].
4) Press qw to switch [IN STANDBY MODE].
 fThe items will switch each time you press the button.
78 - ENGLISH
Chapter 4   Settings - [PROJECTOR SETUP] menu  
						

							[OFF]Disables audio output in the standby mode.
[ON]
Enables audio output in the standby mode when [STANDBY MODE] is set to [NORMAL]. At this 
time, press the  buttons on the remote control or qw buttons on the control panel 
to adjust the volume.
Note
 fAudio cannot be output during standby when [ECO MANAGEMENT] → [STANDBY MODE] is set to [ECO] or [NETWORK] 
(Æpage 77).
Setting audio input selection
Choose the audio input terminal for each input signal.
1) Press as to select [AUDIO SETTING].
2) Press the  button.
 fThe [AUDIO SETTING] screen is displayed.
3) Press as to select one item of [AUDIO IN SELECT].
[COMPUTER1]Set the audio output when [COMPUTER1] input is selected.
[COMPUTER2]Set the audio output when [COMPUTER2] input is selected.
[VIDEO]Set the audio output when [VIDEO] input is selected.
[S-VIDEO]Set the audio output when [S-VIDEO] input is selected.
[HDMI]Set the audio output when [HDMI] input is selected.
[NETWORK/USB]Set the audio output when [NETWORK/USB] input is selected.
4) Press qw to switch the item.
 fThe sub items will switch each time you press the button.
[COMPUTER1]Select one item among [AUDIO IN 1], [AUDIO IN 2] or [AUDIO IN 3].
[COMPUTER2]Select one item among [AUDIO IN 1], [AUDIO IN 2] or [AUDIO IN 3].
[VIDEO]Select one item among [AUDIO IN 1], [AUDIO IN 2] or [AUDIO IN 3].
[S-VIDEO]Select one item among [AUDIO IN 1], [AUDIO IN 2] or [AUDIO IN 3].
[HDMI]Select one item among [HDMI AUDIO IN], [AUDIO IN 1], [AUDIO IN 2] or [AUDIO IN 3].
[NETWORK/USB]Select one item among [NETWORK/USB AUDIO IN], [AUDIO IN 1], [AUDIO IN 2] or [AUDIO IN 3].
Note
 fWhen [MIC] is set to [ON], [AUDIO IN 2] cannot be selected. fEven if [AUDIO IN 2] is selected, it will change to [AUDIO IN 1] automatically when [MIC] is set to [ON].
Using MIC function
1) Press as to select [AUDIO SETTING].
2) Press the  button.
 fThe [AUDIO SETTING] screen is displayed.
3) Press as to select [MIC].
4) Press qw to switch the item.
 fThe items will switch each time you press the button.
[ON] terminal switch to MIC input.
[OFF]MIC is disabled.
5) Press as to select [MIC GAIN].
6) Press qw to adjust the level.
OperationAdjustmentRange
Press the w button.Turns up the MIC mixing gain.0 ~ 63Press the q button.Turns down the MIC mixing gain.
Note
 fWhen [OFF] is selected in MIC function, the MIC GAIN function is not available. fIf the MIC function is set to [ON] when connecting audio signals to the  terminal, loud sound may be output suddenly depending on the setting value of [MIC GAIN].  fWhen [MIC] is set to [ON], no signal is input, AV MUTE function is on, FREEZE function is on or the POWER 
MANAGEMENT function is working, the audio of MIC will be output.
ENGLISH - 79
Chapter 4   Settings - [PROJECTOR SETUP] menu  
						

							[EASY SETTING]
You can set the operation when press the  button on the control panel. 
1) Press as to select [EASY SETTING].
2) Press the  button.
 fThe [EASY SETTING] screen is displayed.
3) Press as to select [FOCUS ASSIST], [SCREEN FIT] or [COLORBOARD].
[FOCUS ASSIST]The level of focus adjustment is displayed in the color and length of th\
e bar. It is supported the 
manual adjustment through rotating the focus ring.
[SCREEN FIT]If it detects a screen frame, the projected image is corrected to fit the screen frame automatically. 
If it does not detect a screen frame, the KEYSTONE starts to work automatically.
[COLORBOARD]The color values will change automatically to reach the optimal color except for the white screen.
4) Press qw to switch the item.
[FOCUS ASSIST]This function is enabled when it is set to [ON]. This function is disabled when it is set to [OFF]. 
[SCREEN FIT]
The image will be displayed in full screen when it is set to [FULL]. The projected image will 
maintain the aspect ratio which is input when it is set to [ORIGINAL].  This function is disabled 
when it is set to [OFF].
[COLORBOARD]This function is enabled when it is set to [ON]. This function is disabled when it is set to [OFF].
Note
 fFor details about EASY SETTING, refer to "Adjusting the projected image via EASY SETTING function" (Æpage 45).
 fIf all items are set to [OFF], press the  button and then [KEY NOT APPLICABLE] massage will 
be displayed on the screen.
[TEST PATTERN]
Displays the test pattern built-in to the projector.
Settings of position, size, and other factors will not be reflected in test patterns. Make sure to display the input signal before 
performing various adjustments.
1) Press as to select [TEST PATTERN].
2) Press the  button.
 fThe [TEST PATTERN] screen is displayed.
3) Press qw to switch the item.
 fThe items will switch each time you press the button. 
ALL WHITE → COLOR BARS → WHITE CROSS ON BLACK BACKGROUND → BLACK CROSS ON THE WHITE 
BACKGROUND → CROSS HATCH → ALL WHITE →...
 fWhen you press the  button or  button, it will display the sub menu of [PROJECT OR SETUP].
Note
 fThe initial setting is ALL WHITE. The initial screen is CROSS HATCH if you have assigned it to the  button.
[FILTER COUNTER]
This function is used to reset the filter use time and set the notification display.
1) Press as to select [FILTER COUNTER].
2) Press the  button.
 fThe [FILTER COUNTER] screen is displayed.
[FILTER 
COUNTER]Displays the using time of the filter.
[TIMER]Sets the timer when you want to display an alert message of filter replacement.
[FILTER COUNTER 
RESET]Resets the filter counter.
80 - ENGLISH
Chapter 4   Settings - [PROJECTOR SETUP] menu