Panasonic LCD Projector Pt Vw345NZ Operating Instructions

ON(G)/STANDBY(R) indicator
The  indicator informs you the status of the power. Confirm the status of the  
indicator before operating the projector.
Indicator statusStatus
OffThe power cord is unplugged.
Red
Lit
The power cord is plugged.
The [STANDBY MODE] is set to [ECO] when the projector is in standby mode and the cooling is 
completed. 
BlinkingThe power is switched off (in standby mode). The [STANDBY MODE] is set to [NETWORK].*1
The power is switched off (in standby mode). The [STANDBY MODE] is set...

Powering On the Projector
Before switching on the projector, make sure all the other devices are correctly connected (Æ pages 35-38) and remove the lens cap.
3)3)
2)1)
1) Connect the power cord to the projector body.
2) Connect the power plug to an outlet.
 fThe power indicator  lights or blinks, and the projector will enter the standby mode. 
3) Press the  button on the control panel or the  button on the remote control.
 fThe power indicator  lights in green and the image is soon projected on the...

Powering Off the Projector
1) 2)1) 2)
2)
3)2)
1) Press the  button on the control panel or the  button on the remote control.
 fThe following message appears.
2) Press qw to select [OK], and press the  button. 
OR 
Press the  button on the control panel or the  button on the remote control again.
 fProjection of the image will stop, and the power indicator  lights in orange. (The fan keeps 
running.)
3) Wait until the  indicator lights or blinks in red.
 fThe projector enters standby mode when the power...

Projecting
Check the connections of the peripheral devices and connection of the power cord (Æ pages 35 - 40) and switch on the power 
(Æ page 42) to start the projector. Select the image and adjust the state of the image.
Selecting the input signal
Select an input signal.
1) Press , , , , ,  or 
 button on the remote control or  button on the contro\
l panel.
 fThe image of the signal being input in the selected terminal is projecte\
d.
 fYou can check the input source through [DETAILED] / [SIMPLE]...

Adjusting the projected image via EASY SETTING function
EASY SETTING function makes the semi-automatically adjustment possible, so that to get the optimal image.
EASY SETTING function including these following setting items:
[FOCUS ASSIST]The color and the length of the bar assists the focus adjustment.
[SCREEN FIT]Detect and correct the image automatically to fit the frame. If you can not detect the frame of the 
screen, Keystone executes automatically.
[COLORBOARD]The color values will change...

Adjust the image to fit the screen according to the SCREEN FIT function's different states.
[FULL]The aspect ratio will change to fit the screen frame.
[ORIGINAL]The aspect ratio will maintain to fit the screen frame. The image may be displayed with the left and right/ top 
and bottom parts cut off. 
Then the COLORBOARD function is activated to get an optimal image. [CORNER CORRECTION] appears and it can be 
adjusted manually if it is necessary (Æ page 64). It will exit without any operation in few...

Basic operations by using the remote control
Using the AUTO SETUP function
The automatic setup function can be used to automatically adjust the res\
olution, clock phase, and image position when 
analog RGB signals consisting of bitmap images such as computer signals \
are being input. Supplying images with bright 
white borders at the edges and high-contrast black and white characters is recommended when the system is in automatic 
adjustment mode.
Avoid supplying images that include halftones or...

Controlling the volume of the speaker
You can control the volume of the projector’s speaker or audio output.
buttons
1) Press the  or  button on the remote control.
 fYou can also press qw on the control panel.
Decreases the volume. 
Increases the volume.
Using the FUNCTION button
Some operations in the menu can be assigned to the  button on the remote control so that it can be used as an 
easy shortcut button.
button
1) Press the  button on the remote control.
To assign functions to the  button 
1)...

Using the MEMORY VIEWER function
It is possible to project the video and pictures which are stored in the USB memory when the USB memory 
inserted into the projector.
 
button
1) Press the  button on the remote control.
 fSwitches the input to MEMORY VIEWER.
Note
 fIf you want to use this function, insert the USB memory directly into the  port.
 fWhen [Miracast(TM)] or [Panasonic APPLICATION] is selected in [CONNECTION LOCK], [KEY NOT APPLICABLE] screen 
will be displayed (Æ page 89).
Using the Miracast...

Using the DIGITAL ZOOM function
(Only for still image-based computer (RGB) and still image-based HDMI signals input)
You can enlarge the center area. You can also change the location of the area to be enlarged. 
 buttons
1) Press the  or < D.ZOOM -> button on the remote control.
 fThe moving screen is displayed.
 fThe [DIGITAL ZOOM] individual adjustment screen is displayed when executing the menu operation. For details, refer 
to [DISPLAY OPTION] → [OTHER FUNCTIONS] (Æ page 73).
 fPressing the  button...