Panasonic Kx-Td308 Digital Super Hybrid System Installation Maintenence Manual

20644
lTimer Programming
Outside-to-Outside Line Call Duration Time
DescriptionSets the maximum time allowed for a conversation between two
outside parties. When the timer expires, the Outside-to-Outside
Line call is disconnected.
SelectionTime (minutes): 1 through 64Default
10min
Programming1.Enter 206.Display: 206 CO-CO TIME
2.Press NEXT.Display example: 
Time:10 min
3.Enter the time.
To change the current entry, press CLEAR and enter the new time.
4.Press STORE.
5.Press END.
Conditionsl You cannot...

44aTimer Programming
207
First Digit Time
DescriptionSets the maximum time allowed between the start of an outside dial
tone and the 
first digit dialed on an outgoing outside call.If an
extension user fails to dial any digits during this time, the 
DTMF
receiver is released.
Selection
Default
ProgrammingTime (seconds): 5 through 120
10 s
1.Enter 207.
Display: 207 1ST DIGIT T
2.Press NEXT.
Display example: Time: 10 set
3.Enter the time.
To change the current entry, press CLEAR and enter the new time....

20844aTimer Programming
Inter Digit Time
DescriptionAssigns the maximum time allowed between digits on an outgoing
toll call.If an extension user fails to dial any digits during this
time, the DTMF receiver is released. This timer applies until the
Toll Restriction check is completed.
SelectionTime (seconds): 5 through 30
Default10 s
Programming1.
2.
3.
4.
5.
Enter 208.Display: 208 INTER DIGIT
Press NEXT.Display example: 
Time:10 set
Enter the time.
To change the current entry, press CLEAR and enter the...

Timer Programming209
Automatic Redial Repeat Times
DescriptionSets the number of times Automatic Redial is tried.Automatic
redialing of the last dialed or saved number is done up to the
specified number of times.
SelectionNumber of times: 1 through 30Default
15 times
Programming1.Enter 209.Display: 209 AUTO RD QTY
2.Press NEXT.
Display example: Attempt:15
3.Enter the number of times.
To change the current entry, press CLEAR and enter the new number
of times.
4.Press STORE.
5.Press END.
Conditionsl...

21044lTimer Programming
Automatic Redial Interval Time
DescriptionSets the interval time between Automatic Redial attempts.
SelectionTime (seconds): 3 through 120 (X 10 is the actual time)
Default40 s
Programming1.Enter 210.Display: 210 REDIAL TIME
2.Press NEXT.Display example: Time:40 
set
3.Enter the time.
To change the current entry, press CLEAR and enter the new time.
4.Press STORE.
5.Press END.
Conditionsl You enter a number from 3 through 120. The actual time is 10 times
your input.
l Program [209]...

44
lTimer Programming211
Dial Start Time
DescriptionSets the number of milliseconds the system waits before dialing
after an outside line is seized.
SelectionTime (milliseconds): 0 through 40 (X 100 is the actual time)
Default500 ms
Programming1.Enter 211.Display: 211 DIAL START
2.Press NEXT.Display example: Time: 500 
msec
3.Enter the time.
To change the current entry, press CLEAR and enter the new time.4.Press STORE.
5.Press END.
Conditionsl You enter a number from 0 through 40. The actual time is a...

21244aTimer Programming
Call Duration Count Start Time
DescriptionSets the number of seconds the system waits between the end of
dialing and the start of the SMDR timer for outgoing toll calls.
When the system has sent out all the digits to the central office and
this timer expires, the system starts counting the call. A display
telephone shows the elapsed time of the call.The starting time and
the duration of a call are recorded in the SMDR record.
Selection
Default
Programming
Time (seconds): 0 through...

44lTimer Programming213
DISA Delayed Answer Time
DescriptionAssigns the number of rings between a call received and the answer
by the DISA feature.
SelectionNumber of rings: 0 through 6
Default1 ring
Programming1.
2.
3.
4.
5.
Enter 213.Display: 213 DISA ANSWER
Press NEXT.Display example: 
Time:lrings
Enter the number of rings.
To change the current entry, enter the new number of rings.
Press STORE.
Press END.
Conditionsl One ring is equivalent to five seconds.
l You cannot leave the entry empty.
Feature...

21644
lTimer ProgrammingMessage Waiting Ring Interval Time
DescriptionSets the Message Waiting ring interval time for a standard
telephone.
SelectionTime (minutes): 0 through 64
Default0 min (no ring)
Programming1.
2.
3.
4.
5.
Enter 216.
Display: 216 MW RING TIME
Press NEXT.
Display example: Interval:0 min
Enter the time.
To change the current entry, press CLEAR and enter the new time.
Press STORE.
Press END.
Conditionsl When the interval time is set to “O”, the telephone does not ring for
Message...

44
lTimer Programming217
Timed Reminder Akzrm Ring Time
DescriptionSets the number of seconds the Timed Reminder alarm rings.
SelectionTime (seconds): 30 through 240
Default30 s
Programming1.
2.
3.
4.
5.
Enter 217.Display: 217 TIMED REMIND
Press NEXT.
Display example: Reminder:30sec
Enter the time.
To change the current entry, enter the new time.
Press STORE.
Press END.
ConditionsNone
Feature ReferencesSection 3, Features
Timed Reminder
Timed Reminder, Remote (Wake-Up Call)
System Programming4-75