Panasonic Kx-Td308 Digital Super Hybrid System Installation Maintenence Manual

10343lSystem Programming
Automatic Access Outside Line Assimment
DescriptionAssigns the sequence in which outside lines will be accessed when
in Automatic Line Access mode. When a user dials the feature
number for automatic line access 
(default=9) or presses the L-CO
button, an idle line is searched for in the programmed outside line
order.
Selectiod
Default
Programmingl Outside line number: 1 through 3 in desired order
123
1.Enter 103.Display: 103 AUTO CO
2.Press NEXT.
Display example: Access:123...

43lSystem Programming105Account Codes
DescriptionAssigns the account codes for Account Code Entry, Verified - All
Calls and Verified - Toll Restriction Override modes. If Verified -
All Calls is assigned in program [508] “Account Code Entry
Mode”, an account code is required to make an outside call. If
Verified 
- Toll Restriction Override is assigned, an account code is
only required for a toll call and overrides toll restriction.
Selection
Default
All locations - Not stored
Programming1.Enter 105....

10643lSystem Programming
Station Hunting Type,
DescriptionUsed to enable or disable hunting and set the Station Hunting type
for each extension group. There are six Station Hunting types
available: Circular, Termination, Voice Mail (VM), Automated
Attendant (AA), Ring Group and Uniform Call Distribution (UCD).
If circular hunting is assigned for a group, all of the extensions in
the group are searched until an idle one is found.If termination
hunting is assigned, searching stops at the extension which...

43aSystem Programming
106
station Hunting Type 
(contd.)
Conditionsl Program [602] “Extension Group Assignment” is used to assign the
extension group members.
l The system supports a maximum of four jacks for connection to a Voice
Processing System as VM or AA ports.
Feature ReferencesSection 3, Features
Ring Group
Station HuntingUniform Call Distribution (UCD)
Voice Mail IntegrationSystem Programming4-39 

107 4.3System Programming
System Password
DescriptionAssigns the password required for entering System Programming
mode.
SelectionPassword: 4 through 7 digits
Default1234
Programming1.
2.
3.
4.
5.
Conditions
Enter 107.Display: 107 SYS PASSWORD
Press NEXT.
Display:Password:1234Enter a password.
To change the current entry, press CLEAR and enter the new
password.
Press STORE.
Press END.
l The password can be from four to seven digits long. The valid numbers
are from 
0 through 9.
l If less than four digits...

43lSystem Programming
108
Automatic Hold by CO / DSS Button
DescriptionEnables or disables automatically holding an outside call when a
DSS button or a CO button on a proprietary telephone is pressed.
Through this assignment, each button acts as follows:
- Pressing the DSS button holds an outside call and quickly
transfers it to an extension without pressing the TRANSFER
button.
- Pressing another CO button holds the current outside call.
Selectionl Button: DSS or CO
l Enable / Disable
DefaultDSS button...

110,43lSystem Programming
Caller ID Code Set.1 .
DescriptionSets the identification code of the calling party (Caller ID Code) to
utilize Caller ID Service provided by a specific central office (CO).
If an ID Code transmitted from CO is found in the Caller ID Code
Table, the caller’s ID Code or a name given to the code in program
[ 11 
l] “Caller ID Name Set” is displayed on the telephone, allowing
the called party to recognize the caller.
Selectionl Location number: 001 through 100
l Caller ID Code: 11...

43aSystem Programming111
Caller ID Name Set
DescriptionWith Caller ID Service, the calling party is displayed either by its
ID Code or by its name.If the name display is required, use this
program to give a name to a caller ID Code stored in program [ 1 
lo]
“Caller ID Code Set”.
Selectionl Location number: 001 through 100
l Caller ID Name: 15 characters (max.)
DefaultAll locations - Not stored
Programming1.Enter 111.Display: 111 CALLER NAME
2.Press NEXT.Display: Location NO?+
3.Enter a location number....

113430System Programming
VM Status DTMF Set
DescriptionSets the DTMF signals transmitted to your Voice Processing
System (VPS) to inform the VPS of the VPS ports states quickly:
The following signals are sent to the VPS with the assigned DTMF
signals:
RBT (ringback tone) : This signal is sent when calling an
extension.
BT (busy tone): This is sent when the called extension is
busy.
ROT (reorder tone): This is sent when the dialed number is
invalid.
DND (DND tone): This is sent when the other extension...

System ProgrammingVM SttZtUS DT&fF Set (contd.)113
3.Enter a DTMF signal number.
To delete the current entry, press CLEAR.
To change the current entry, press 
CLEAR.and enter the new number.4.
5.
Press STORE.
To program another selection, keep pressing NEXT or PREVuntil the desired selection is displayed.
6.Repeat steps 3 through 5.
7.Press END.
Conditionsl A DTMF signal number can have a maximum of three digits, consisting
of 0 through 9, * , # and PAUSE.
l The DTMF signals arc sent to the extensions in...