Panasonic Kx-Td308 Digital Super Hybrid System Installation Maintenence Manual

413460Outside Line Programming
Flash Time
., ‘”
DescriptionAssigns the length of the flash time.If your system is installed
behind a host PBX or 
Centrex line, External Feature Access (EFA)
is necessary to obtain 
their services. To enable it, select a required
hooking signal sending time for the outside line.
Selectionl Outside line (CO) number: 1 through 3, * ( * =all outside lines)
l Time (milliseconds): Disable (no EFA) / 80 / 96 / 112 / 200 / 300 /
400/500/600/700/800/900/1ooo/
1100 / 1200...

460Outside Line Programming414
Disconnect Time
DescriptionDetermines the amount of time between successive accesses to the
same outside line.
Selectionl Outside line (CO) number: 1 through 3, * ( * =all outside lines)
l Time (seconds): 1.5 / 4.0
l Time (seconds): 1.5 / 4.0
DefaultAll outside lines - 1.5 s
Programming1.
2.
3.
4.
5.
6.
7.
8.
Enter 414.
Display: 414 DISCONNECT
Press NEXT.
Display: CO Line NO?+
Enter an outside line number.
To program outside line number 1, you can also press NEXT.
Display...

41546lOutside Line Programming
CPC Signal Detection Outgoing Set
DescriptionEnables or disables CPC Signal Detection during the time between
the originated outside call and the established outside call.If this is
enabled, the system disconnects the line with the time set in
program 
[405] “CPC Signal Detection Incoming Set” when the
CPC Signal is detected.
Selectionl Outside line (CO) number: 1 through 3, * ( * =all outside lines)
l Enable (detection) / Disable (no detection)
DefaultDisable...

46lOutside Line Programming416
Reverse Circuit Assignment
DescriptionEnables or disables to detect Reverse Circuit.
Selectionl Outside line (CO) number: 1 through 3, * ( * =all outside lines)
l Regular (no detection) / Reverse (detection)
DefaultRegular
Programming1.
2.Press NEXT.
Display: CO Line NO?+
3.Enter an outside line number.
To enter outside line number 1, you can also press NEXT.
Display example: COl:Regular
4.
5.
6.Keep pressing SELECT until the desired selection is
displayed.
Press STORE.
To...

417460Outside Line Programming
Outside Line Name Assignment
DescriptionAssigns names of the company or customer to each outside line so that
the operator or extension user can find the destination which the caller
is trying to reach before answering.If Caller ID is assigned, each
extension can select either the initial display, Caller ID or line name.
Selection
Default
All outside lines - Not stored
Programming1.Enter 417.
l Outside line (CO) number: 1 through 3, * ( * =all outside lines)
l Name: 10...

47
lCOS Programming500-501
Toll Restriction Level- Day /Night
DescriptionEach extension must be assigned a Class of Service (COS). These
programs set the toll restriction value for each COS in day or night
mode.
Selectionl COS number: 1 through 8, * ( * =all COS)
l Level number: 1 through 8
DefaultCOS 1 through 7 - Level 1 - Day / Night;
COS 8 
- Level 7 - Day / Night
Programming1.
2.
3.
4.
5.
6.
7.
8.
Conditions
Enter a program address (500 for day or 501 for night).
Display example: 500 TRS DAY LVL...

502470COS Programming
Extension-to-Outside Line Call Duration Limit
DescriptionThis program allows you to restrict the duration of outside calls on
a Class of Service (COS) basis.
Selectionl COS number: 1 through 8, * ( * =all COS)
l Disable (no limit) / Enable (limit)
Default,All COS - Disable
Programming1.
2.
3.
4.
5.
6.
7.
-8.Enter 502.
Display: 502 EXT-CO TIMER
Press NEXT.Display: COS NO?+
Enter a COS number.
To enter COS number 1, you can also press NEXT.Display example: 
COSl:Disable
Keep pressing...

47
lCOS Programming503
Call Transfer to Outside Line
DescriptionThis program determines which Classes of Services (COS) are
allowed to perform the Call Transfer to Outside Line function.Selection
l COS number: 1 through 8, 3c ( % =all COS)
l Enable / Disable
DefaultAll COS - Disable
Programming1.Enter 503.Display: 503 CALL XFER CO
2.Press NEXT.Display: COS NO?+
3.Enter a COS number.
To enter COS number 1, you can also press NEXT.Display example: 
COS1:Disable
4.Keep pressing SELECT until the desired...

50447aCOS Programming
Call Forwarding to Outside Line
DescriptionThis program determines which Classes of Services (COS) are
allowed to perform the Call Forwarding to Outside Line function,
Selectionl COS number: 1 through 8, * (* =all COS)
l Disable / Enable
DefaultAll COS - Disable
Programming1.
2.
3.
4.
5.
6.
7.
8.
Enter 504.
Display: 504 CALL FWD CO
Press NEXT.
Display: COS NO?-+
Enter a COS number.
To enter COS number 1, you can also press NEXT.
Display example: COS1:Disable
Keep pressing SELECT...

47
lCOS Programming505
Executive Busy Override
DescriptionDetermines which Classes of Services (COS) are allowed to
perform Executive Busy Override 
- Extension / Outside Line.
Executive Busy Override allows the user to interrupt an established
call.
Selectionl COS number: 1 through 8, * ( * =all COS)
l Disable / Enable
DefaultAll COS - Disable
Programming1.
2.
3.
4.
5.
6.
7.Repeat steps 4 through 6.
8.Press END.
Conditions
Enter 505.Display: 505 EXEC BSY OR
Press NEXT.Display: COS NO?+
Enter a COS...