Panasonic Kx-Td308 Digital Super Hybrid System Installation Maintenence Manual

402 4~Outside Line Programming
Dial Mode Selection (contd.)
Conditionsl To assign all lines to one selection, press the Jc key in step 3. In this
case, the display shows the contents programmed for outside line 1.
l If DTMF is assigned, set the DTMF time of the line in program [404]
“DTMF lime”.
l If pulse or call blocking is assigned, set the pulse speed of the line in
program 
[403] “Pulse Speed Selection”, and set the pulse break ratio
and inter-digit pause in program 
[990] “System Additional...

460Outside Line Programming
Pulse Speed Selection
403
Selection
DefaultAll outside lines 
- 10 pps
Programming1.Enter 403.
DescriptionAn outside line set for pulse or call blocking mode in program
[402] “Dial Mode Selection” can have two pulse rates, 10 pps (low)
and 20 pps (high). This program sets the pulse speed for each
outside line set to pulse or call blocking mode.
l Outside line (CO) number: 1 through 3, * ( * =all outside lines). 
lOpps/2Opps
Display: 403 PULSE SPEED
2.Press NEXT.
3.
4.
5.
6....

Outside Line ProgrammingDTMF Time
DescriptionAn outside line set to DTMF mode in program [402] “Dial Mode
Selection” can have two settings. This program sets the duration of
the DTMF signals sent to an outside line to DTMF mode.
Selectionl Outside line (CO) number: 1 through 3, * ( * =all outside lines)
l Time (milliseconds): 80 / 160
DefaultAll outside lines - 80 ms
Programming1.Enter 404.
Display: 404 DTMF TIME
2.Press NEXT.
Display: CO Line NO?+
3.Enter an outside line number.
To enter outside line...

46lOutside Line Programming405
CPC Signal Detection Incoming Set
DescriptionAssigns the expected minimum duration of the CPC Signal on
incoming outside calls. If this is programmed, the system
disconnects the line when the CPC Signal is detected.
Selectionl Outside line (CO) number: 1 through 3, * ( * =all outside lines)
l Time (milliseconds): Disable (no detection) / 100 / 200 / 300 /
400/500/600
DefaultAll outside lines - 400 ms
Programming1.Enter 405.Display: 405 CPC INCOMING
2.Press NEXT.Display: CO...

406 46Outside Line Programming
Caller ID Assignment
DescriptionEnables the Caller ID feature for the outside lines to which a Caller
ID Service is offered by a Central Office by contract.
Selectionl Outside line (CO) number: 1 through 3, * ( * =all outside lines)
l Enable / Disable
DefaultAll outside lines - Disable
Programming1.
2.
3.
4.
5.
6.
7.Repeat steps 4 through 6.
8.Press END.
Conditions
Enter 406.
Display: 406 CALLER ID CO
Press NEXT.
Display: CO Line NO?+
Enter an outside line number.
To enter...

46lOutside Line Programming 407-408
DIL I:1 Extension- Day /Night
DescriptionThe Direct In Lines (DIL) 1: 1 feature allows incoming outside calls
to be directed to a specific extension. When an outside line is
assigned as DIL 1: 1, it is necessary to assign the destination. These
programs specify the extension number for day or night mode.
Selection
DefaultAll outside lines 
- Disable - Day / Night
Programming1.Enter a program address (407 for day or 408 for night).Display example: 407 DIL 
1:l DAY...

4091410 4*tFiOutsidti Line Programming
Intercept Extension- Day /Night
DescriptionIntercept Routing provides an automatic redirection of calls which
cannot or have not been answered. These programs set the
destination in both day and night modes for each outside line.
Selectionl Outside line (CO) number: 1 through 3, * ( x =aIl outside lines)
l Extension number: 2 through 4 digits / Disable (no Intercept
Routing)
DefaultAI1 outside lines - Disable - Day / Night
Programming1.
2.
3.
4.
5.
6.Display: CO...

46lOutside Line Programming411
Host PBX Access Codes
DescriptionAssigns Host PBX or Centrex access codes. If the.system is
installed behind a host PBX or a 
Centrex system, an access code is
required to make an outside 
/ Centrex call or to access Centrex
features. Up to four codes can be stored for an outside line
assigned to the line.
Selection
Default
Programmingl Outside line (CO) number: 1 through 3, * ( * =all outside lines)
l Access code: 1 or 2 digits, four different entries (max.)
All outside...

41146lOutside Line Programming
Host PBX Access Codes (contd.)
Conditionsl This program is only required if a host PBX or Centrex line is
connected to the system.
l There is a maximum of four access codes per outside line. Each code
has one or two digits, consisting of 0 through 9, and * .
l If conflicting access codes (such as 8 and 81) are stored for the same
outside line, the l-digit code (8) only will be in effect.
l When the programmed codes are dialed, Automatic Pause Insertion and
Toll Restriction...

46lOutside Line Programming412
Pause Time
DescriptionAssigns the length of the pause time. The programmed pause time
is automatically inserted after a line access code or a host PBX
access code programmed in 
[41 l] “Host PBX Access Codes” or
manually inserted if the 
PAUSE button is pressed by the user.
Selectionl Outside line (CO) number: 1 through 3, * ( * =all outside lines)
l Time (seconds): 1.5 / 2.5 / 3.5 / 4.5
DefaultAll outside lines - 1.5 s
Programming1.
2.
3.
4.
5.
6.
7.
8.
Enter 412.
Display:...