Panasonic Kx-Ta624 Advanced Hybrid System Installation Manual

4.2 System Programming
DISA Built-in Auto Attendant
501
System Programming  4-83
DescriptionAssigns the DISA built-in auto attendant number. The extension
number can be assigned as a one digit number and used as a DISA
built-in auto attendant number.
Selection• DISA built-in auto attendant (AA) number: 0 – 9
• Jack number: 01 – 24 / Ring Group number: 1 – 8
DefaultAll numbers — Not stored
Programming1.Enter 501.
Display: DISA Built-In
2.Press NEXT.
Display example: AA NO? ®
3.Enter a DISA built-in auto...

4-84 System Programming
4.2 System Programming
OGM Mode Selection
502
DescriptionSelects how the two outgoing messages (OGM) are used. There are
two modes as follows.
MODE 1: both OGM1 and OGM2 are used for DISA1 so that the
system can receive two incoming calls via DISA at the
same time.
MODE 2: OGM1 is used for DISA1 and OGM2 is used for
DISA2.
SelectionMODE 1 / MODE 2
DefaultMODE 1
Programming1.Enter 502.
Display: OGM Selection
2.Press NEXT.
Display example: MODE 1
3.Keep pressing SELECTuntil the...

4.2 System Programming
FAX Connection
503
System Programming  4-85
DescriptionAssigns which jack can receive facsimile data when the system
receives a facsimile transmission signal via the Direct Inward
System Access (DISA) feature.
SelectionJack number: 01 – 24 / Disable(Facsimile data cannot be received.)
DefaultDisable
Programming1.Enter 503.
Display: Fax Connection
2.Press NEXT.
Display example: FAX :Disable
3.Enter a jack number.
To assign no FAX jack, press CLEAR.
To delete the jack number, press...

4-86 System Programming
4.2 System Programming
DISA Delayed Answer Time
504
DescriptionAssigns the time from a call being received and answered using the
DISA feature.
Selection0 sec / 3 sec / 6 sec / 12 sec(seconds)
Default3 sec
Programming1.Enter 504.
Display: Ans Delay Time
2.Press NEXT.
Display example: Time: 3sec
3.Keep pressing SELECTuntil the desired selection is
displayed.
4.Press STORE.
5.Press END.
Condition• The outside (CO) lines which are assigned as “Enable” in program [900]
“Caller ID...

4.2 System Programming
DISA Waiting Time after OGM
505
System Programming  4-87
DescriptionSelects the time that the system waits for the DTMF signals or
CNG tone after the outgoing message.
Selection0 sec / 5 sec / 10 sec / 15 sec(seconds)
Default5 sec
Programming1.Enter 505.
Display: DISA Wait Time
2.Press NEXT.
Display example: Time :5sec
3.Keep pressing SELECTuntil the desired selection is
displayed.
4.Press STORE.
5.Press END.
Condition• An optional OGM/FAX Detection card is necessary.
Feature...

4-88 System Programming
4.2 System Programming
DISA Busy Mode
506
DescriptionSelects the mode when destination extension of the call via DISA is
busy. There are three modes as follows.
Call Waiting: a call waiting tone is sent and then the call is held
until the called party responds.
Disconnect: the call is disconnected after the busy tone.
DISA2: OGM2 is sent to the caller and the system waits for
another destination when the first destination is busy.
SelectionCall Waiting / Disconnect / DISA2...

4.2 System Programming
DISA Intercept Mode
507
System Programming  4-89
DescriptionIntercept Routing provides an automatic re-direction of DISA calls
which cannot or have not been answered within the programmed
time. This program is used to select whether the call is
disconnected or re-directed.
Intercept: the call is directed to the extensions assigned in
programs [408]–[410].
Disconnect: the call is disconnected.
SelectionDisconnect / Intercept
DefaultIntercept
Programming1.Enter 507.
Display: DISA...

4-90 System Programming
4.2 System Programming
DISA Ringing Time before Intercept
508
DescriptionSelects the time for the Intercept Routing — No Answer (IRNA)
feature. If a DISA call is not answered within the programmed
time, the call will be redirected to the programmed extension.
Selection10 sec / 20 sec / 30 sec / 40 sec / 60 sec / 120 sec(seconds)
Default20 sec
Programming1.Enter 508.
Display: DISA Befor IRNA
2.Press NEXT.
Display example: Time: 20sec
3.Keep pressing SELECTuntil the desired...

4.2 System Programming
DISA Ringing Time after Intercept
509
System Programming  4-91
DescriptionSelects the time that the extension will ring for after being
re-directed by the Intercept Routing — No Answer (IRNA) feature.
If a call is not answered within the programmed time, the call will
be disconnected.
Selection10 sec / 20 sec / 30 sec / 40 sec / 60 sec / 120 sec (seconds)
Default20 sec
Programming1.Enter 509.
Display: DISA After IRNA
2.Press NEXT.
Display example: Time: 20sec
3.Keep pressing...

4-92 System Programming
4.2 System Programming
DISA No Dial Mode
510
DescriptionSelects the mode when nothing is dialed after the OGM or a beep
after a programmed length of time for the DISA1 and DISA2
modes. There are two modes as follows.
Intercept: the call is directed to the extensions assigned in
programs [408]–[410] for the time programmed in
[509] “DISA Ringing Time After Intercept”.
Disconnect: the call is disconnected.
Selection• DISA1 / DISA2
• Intercept / Disconnect
DefaultDISA1 and DISA2 —...