Panasonic Kx-Ta624 Advanced Hybrid System Installation Manual

4.2 System Programming
Outside (CO) Line Mode — Day/Night/Lunch (contd.)
414–416
System Programming  4-73
Conditions• “DISA1” must be selected when an optional OGM/FAX Detection card
is notinstalled and if the user wants to use Internal DISA.
• There are two outgoing messages. Program [502] determines how each
message is used.
• To assign all the outside (CO) lines to the same selection, press the 
key in step 3. In this case, the display will show:CO :Mixed.
Feature ReferencesSection 3, Features
Direct...

4-74 System Programming
4.2 System Programming
Pause Time
417
DescriptionAssigns the length of the pause time.  The programmed pause time
is automatically inserted after a line access code or host PBX access
code programmed in [403] “Host PBX Access Codes”, or can be
manually inserted by the user with the PAUSEbutton.
Selection• Outside (CO) line number: 1 – 6, ( = all outside (CO) lines)
• Time (seconds): 1.5 sec / 2.5 sec / 3.5 sec / 4.5 sec
DefaultAll outside (CO) lines — 1.5 sec
Programming1.Enter...

4.2 System Programming
Flash Time
418
System Programming  4-75
DescriptionAssigns the length of the flash time. If the system is installed
behind a host PBX, External Feature Access (EFA) is necessary to
obtain its services. To enable this feature, select the required
hooking signal sending time for an outside (CO) line.
Selection• Outside (CO) line number: 1 – 6, ( = all outside (CO) lines)
• Time (milliseconds): 80 ms / 100 ms / 160 ms / 300 ms / 600 ms /
900 ms / 1200 ms 
DefaultAll outside (CO) lines...

4-76 System Programming
4.2 System Programming
Automatic Designated Outside (CO) Line Access
419
DescriptionAssigns the sequence in which outside (CO) lines will be accessed
during the Automatic Line Access mode. When a user dials the
feature number for automatic line access (9), an idle line is
searched for in the programmed outside (CO) lines.
Selection• Outside (CO) line number: 1 – 6, ( = all outside (CO) lines)
• Enable / Disable
DefaultAll outside (CO) lines — Enable
Programming1.Enter 419....

4.2 System Programming
Calling Party Control (CPC) Signal
420
System Programming  4-77
DescriptionAssigns the required minimum duration of the CPC Signal for
incoming outside calls. If programmed, the system disconnects the
line when the CPC signal is detected.
Selection• Outside (CO) line number: 1 – 6, ( = all outside (CO) lines)
• Time number (milliseconds): 00(Disable) / 01 (22 msec)/ 
02 (30 msec)/ 03 (38 msec)/ 04 (46 msec)/ 05 (54 msec)/ 
06 (62 msec)/ 07(70 msec)/ 08 (78 msec)/ 09 (86 msec)/...

4-78 System Programming
4.2 System Programming
Calling Party Control (CPC) Signal (contd.)
420
6.To program another outside (CO) line, press NEXTor
PREV, or SELECTand enter the desired outside (CO) line
number.
7.Repeat steps 4 and 6.
8.Press END.
Conditions• To assign all outside (CO) lines to the same selection, press the  key
in step 3. In this case, the display will show:CO  : N= Mixed.
• Program [421] “CPC Detection for Outgoing Calls” is used to program
CPC Signal Detection for outgoing outside...

4.2 System Programming
CPC Detection for Outgoing Calls
421
System Programming  4-79
DescriptionEnables or disables CPC Signal Detection during an outside call in
progress. If enabled, the system disconnects the line at the time set
in program [420] “Calling Party Control (CPC) Signal” when the
CPC signal is detected.
Selection• Outside (CO) line number: 1 – 6, ( = all outside (CO) lines)
• Enable(detect)/ Disable(will not detect)
DefaultDisable
Programming1.Enter 421.
Display: CPC Out Detect
2.Press...

4-80 System Programming
4.2 System Programming
Disconnect Time
422
DescriptionDetermines the amount of time to send the disconnect signal from
the system to the Central Office or host PBX.
Selection• Outside (CO) line number: 1 – 6,  ( = all outside (CO) lines)
• Time (seconds): 0.5 sec / 1.5 sec / 4.0 sec 
DefaultAll outside (CO) lines – 1.5 sec
Programming1.Enter 422.
Display: Disconnect Time
2.Press NEXT.
Display: CO NO? ®
3.Enter an outside (CO) line number.
Pressing NEXTalso can enter outside (CO)...

4.2 System Programming
Outside (CO) Line Ringing Pattern Selection
423
System Programming  4-81
Selection• Outside (CO) line number: 1 – 6,  ( = all outside (CO) lines)
• Single / Double / Triple
DefaultSingle
Programming1.Enter 423.
Display: CO Ring Pattern
2.Press NEXT.
Display: CO NO? ®
3.Enter an outside (CO) line number.
Pressing NEXTalso can enter outside (CO) line number 1.
Display example: CO 1:Single
4.Keep pressing SELECTuntil the desired time is displayed.
5.Press STORE.
6.To program another...

4-82 System Programming
4.2 System Programming
DISA Incoming Dialing Mode Selection
500
DescriptionSelects the mode of an incoming DISA call. There are two modes
as follows.
Without AA: the system can receive an extension number, line
access number and operator call number, and send the
call to the designated destination.
With AA: the system can receive an extension number, line
access number, operator call number and auto
attendant (AA) number, and send the call to the
designated destination....