Panasonic Kx-Ta624 Advanced Hybrid System Installation Manual

4.2 System Programming
DISA Security Type
511
System Programming  4-93
DescriptionAssigns the security mode for outside calls from a DISA (Direct
Inward System Access) caller. There are three modes: None
Security, Trunk Security (outside (CO) line security), and All
Security. None Security mode allows the caller to access an outside
(CO) line without dialing a DISA security code. Trunk Security
mode requires the caller to enter a DISA security code before
making an outside call. All Security mode...

4-94 System Programming
4.2 System Programming
DISA Security Codes
512
DescriptionAssigns the DISA (Direct Inward System Access) Security Codes.
Selection• Code number : 1 – 4
• DISA security code: 4 digits
DefaultAll codes — Not stored
Programming1.Enter 512.
Display: Security Code
2.Press NEXT.
Display: CODE-01:Not Stored
3.Enter acode number.
Display example: CODE-01: 1234
4.Enter a DISA security code.
To change the current entry, press CLEARand enter the new code.
5.Press STORE.
6.To program another...

4.2 System Programming
Cyclic Tone Detection
513
System Programming  4-95
DescriptionSelects the number of times that the system detects the cyclic tone.
The system regards a call as completed after detecting the cyclic
tone the programmed number of times.
SelectionDisable (will not detect)/ 2 Times / 3 Times / 4 Times
Default4 Times
Programming1.Enter 513.
Display: Tone Detection
2.Press NEXT.
Display example: 4 Times
3.Keep pressing SELECTuntil the desired selection is
displayed.
4.Press STORE.
5.Press...

4-96 System Programming
4.2 System Programming
FAX Tone Detection
514
DescriptionSelects the number of times the CNG tone (FAX tone) is detected.
An incoming fax call via the Direct Inward System Access (DISA)
feature is detected by the system after receiving the CNG tone the
assigned number of times.
Selection1 Time / 2 Times
Default1 Time
Programming1.Enter 514.
Display: FAX Detection
2.Press NEXT.
Display example: 1 Time
3.Keep pressing SELECTuntil the desired selection is
displayed.
4.Press STORE....

4.2 System Programming
Intercept Time for Internal DISA
515
System Programming  4-97
DescriptionSelects the time that the system waits for DTMF signals when a call
is received via the internal DISA. If the system does not receive the
DTMF signals within the assigned period of time, the call will be
disconnected or sent to extensions programmed in [408]–[410]
according to program [510].
Selection3 sec / 6 sec / 9 sec(seconds)
Default3 sec
Programming1.Enter 515.
Display: Internal DISA
2.Press NEXT....

4-98 System Programming
4.2 System Programming
DISA Incoming Assignment
516
DescriptionAssigns the extensions which can receive calls via DISA.
Selection• Jack number:01 – 24, ( =all jacks)
• Enable / Disable
DefaultAll jacks — Enable
Programming1.Enter 516.
Display: DISA Assign
2.Press NEXT.
Display example: Jack NO? ®
3.Enter a jack number.
Pressing NEXTalso can enter jack number 01.
Display example: #01:Enable
4.Keep pressing SELECTuntil the desired selection is
displayed.
5.Press STORE.
6.To program...

4.2 System Programming
DISA AA Wait Time
517
System Programming  4-99
DescriptionSelects the time that the system waits for a second digit entry. If the
timer expires, the system will assume that the first digit is a DISA
built-in auto attendant number (AA number) if an AA number is
assigned in program [501] “DISA Built-in Auto Attendant”. 
For example, if a number is not dialed within the programmed time
after dialing 1, the system will assume that “1” is an AA number.
Selection1 sec / 2 sec / 3 sec / 4...

4-100 System Programming
4.2 System Programming
DISA Tone Selection after the Security Code
518
DescriptionEnables or disables sending a beep to a caller after the Security
Code is entered. If enabled, a beep is sent to the caller when the
code entered is the same as one of the security codes assigned in
program [512] “DISA Security Codes”.
SelectionEnable / Disable
DefaultEnable
Programming1.Enter 518.
Display: DISA Dial Tone
2.Press NEXT.
Display: Enable
3.Keep pressing SELECTuntil the desired...

4.2 System Programming
Extension Group Assignment
600
System Programming  4-101
DescriptionAssigns an extension group for each extension. Extension groups
are used for Group Call Pickup, Station Hunting, Paging – Group
and Ring Group.
Selection• Jack number:01 – 24, ( = all jacks)
• Extension group number (EXT GRP):1 – 8
DefaultAll jacks — EXT GRP-1
Programming1.Enter 600.
Display: Extension Group
2.Press NEXT.
Display: Jack NO? ®
3.Enter a jack number.
Pressing NEXTalso can enter jack number 01.
Display...

4-102 System Programming
4.2 System Programming
TRS – Class of Service (COS) Assignment — Day/Night/Lunch
601–603
DescriptionPrograms Toll Restriction (TRS) – Class of Service (COS) for each
extension.
Selection• Jack number: 01 – 24, ( = all jacks)
• COS-1 / COS-2 / COS-3 / COS-4 / COS-5
DefaultAll jacks — COS-1
Programming1.Enter a program address (601 for day, 602 for night, or
603 for lunch).
Display example: Day  Toll Restr
2.Press NEXT.
Display: Jack NO? ®
3.Enter a jack number.
Pressing NEXTalso...