Panasonic Kx-T123211d Installation Manual

~~~~~~~~~~~~~~~~~~~~~~~~~~~‘~~- until the desired memory code number (01 through 20) 
appears 
.- .............. .................._ CDE= exchange code with 3 digits 
Nothing is stored 
. . . . . ..-default (all 20 memory codes) 
m............................................. AB=(Olm : memory number 01 
12(kl: memory number 20 ’ 
Description 
The exchange code and area code usually differ 
for local and long distance calls, but in some 
when Area Type B or Type C is selected with the 
“Area Type...

,...........,.................. 
until the desired memory number (01 through 20) appears 
i . . ...’ . . . . . . . . . . ............... CI)E = areacode with 3 digits 
Nothing is stored ,.....,defauIt (all 20 memory numbers) 
. 
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
AB= [~~~~ : memory number 01 for storage of an area code 
/a’k[ : memory numb& 20 
for storage of an area code 
I 
Description 
For Service Class 3 (see “Toll Restriction” on 
page 3-17) up to 20...

~.~......~~.~........“‘..‘.‘.’ until the desired memory number (01 through 20) appears 
: ........................ CDE = exchange co& with 3 digits 
Nothing is stored 
......... default (all 20 memory numbers) 
. AB=pi/il: memory number 01 for storage of.exchange code 
: memory number 20 
for storage of exchange code 
Description 
For Service Class 5 (See “Toll Restriction” on 
page 3-17), up to 20 exchange codes can be 
selected for use in local dialing (charged). 
All exchange codes except those...

~~~~~~~~~~~~~~~~~~~~“~‘~~~~~~~ until the desired memory number (01 through 20) appears 
I 
I :........................... 
I 
CDE = exchange code with 3 digits 
Nothing is stored,..... 
default (all 20 memory numbers) 
I I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
I 
AB=mrl: memory number 01 for storage of exchange code 
I ml 2 0 : memory number 20 for storage of exchange code 
I 
Description 
For Service Class 7 (See “Toll Restriction” on 
page 3-17), up to 20...

A= 111: to sound after 1 minute 
0 2 :after 2 minutes 
cl 3 :after 3 minutes . . . . . . . . . default 
cl 4 :after 4 minutes 
cl 5 :after 5 minutes 
cl 6 :after 6 minutes 
cl 7 : after 7 minutes 
cl 6 :after 8 minutes: 
q 9 : after 9 minutes 
Description 
An alarm tone will be heard at the holding extension 
to remind that you still has a call on hold. 
The reminder will sound after 3 minutes but can 
be changed. 
There are 9 choices ranging from 1 minute to 9. 
An alarm tone is heard from the built-in...

_.....,........................................ 
until the desired time appears 
: 30sec--default 
1 min. 
1.5min.’ 
: 
2min. 
Disable 
Description 
When the handset of the holding extension is 
replaced on call, you may have the automatic 
hold recall after the desired time elapses. 
The hold recall can be removed or added. Example: 
1.5 minutes= [18Im ~ ml 
@GGzlFq 
Programming Table 
See page 7-6. 
Programming 
1. Dial (18). 
“Hold Recall Time” will be displayed. 
2. Press the NEXT button. 
“Time: 30...

until the desired mode appears 
.................. 
Description Programming ’ 
If a call is transferred to an extension, and the 
other extension does not answer the transferred 
call within 30 seconds, the call will return to you. 
The time may be changed to 2 minutes. 
Refer to “Call Transfer-To Extension” on page 4- 18. 
1. 
2. 
3. 
4. 
5. Dial (19). 
“Transfer Recall” will be displayed. 
Press NEXT button. 
“Time: 30 set” will be displayed and the “30” 
will blink. 
Press the SELECT button to...

until the desired time appears 
1 ring delay 
2rings delay 
3rings delay ._ default 
4rings delay 
-. ‘_ _ - 
Description 
Enables programming the call forwarding 
delayed start time (after 1, 2, 3, or 4 rings) in 
case of no receiving the call when the “Call 
Forwarding-Busy or No Answer” (on page 4-27) 
feature is set. 
Programming 
1. Dial (20). 
“Call FWD Delay” will be displayed. 
2. Press the NEXT button. 
“3 rings delay” will be displayed and will 
blink. 
3. Repeat pressing the SELECT button...

until the desired time appears 
lsec : dials after I second 
2sec : dials after 2 seconds 
3sec : dials after 3 seconds . . . . . . ..-. default 
4sec : dials after 4 seconds 
Description 
Enables programming of the pickup dial (on 
page 5-18) start time (the delay between 
picking up the handset and automatic dialing). 
The default is 3 sec.,Which can be changed to 1, 
2, or 4 sec. 
Programming Table 
See page 7-7. 
Programming 
1. Dial (21). 
“Pickup Dial Time” will be displayed. 
2. Press the NEXT...

_............................................_ AB= a_ 
: to limit the time to 1 minute 
! 
OD 1 0 : 
to limit the time to 10 minutes . . . . . . default 
Description 
Enable limiting of the time any outside line can be 
used when “Call Transfer-To Outside Line” (on 
page 4-19) or “Call Forwarding-To Outside Line” 
(on page 4-29) is used to forward a outside call 
to an outside line or when you call to any outside 
line using DISA. 
Conditions 
l To erase a wrong entry, press the CLEAR 
button....