Panasonic Kx-T123211d Installation Manual

PROGRAMMING 
To activate this system, the requirements from telephone company and the customer must be programmed once 
the Power Switch has been turned on. 
1. At extension connected to jack number 01: All system 
programming changes’(example : system clear, 
toll restriction, system speed dialing entry-..) are 
done through extension connected to jack 
. 
number 01. 
0 Extension connected to jack number 01 must 
2. System Program Switch setting: 
The System Program Switch located on the 
KX-T123211...

When the System Program Switch on the KX-T123211 is set to the “PITS” position, the function of the 
KX-T123230 or KX-T123235 connected to jack number 01 will change as follows. 
+ 
+ 
button7 
button CLEAR button 
PROGRAMMABLE 
Overlay 
 FEATURE button 
r- LIQUID CRYSTAL 
Display (LCD) 
KX-T123230 or KX-T 
FLASH button 
END button i ZiSEEFIy) button 
123235 
3-2  

1. Turn the Power Switch ON. 
2. Set the System Program Switch to “PITS” position. 
The LCD on the KX-T123230 or KX-T123235 will show “SYS-PGM NO ?&‘I. 
l Be sure the handset of the extension connected to jack number 
01 is in the cradle and the speakerphone button is off. 
3. To program automatic line access number 9 and the phone 
number 987-654-3210 into speed access code 00. (Refer to 
page 3-5.) 
KX-T123230 or KX-T123235 at extension connected to 
jack number 01. 
(Extension connected to jack number...

System Feature 
L r.............................................................. . . . . . . . . . . . . . . . . . . . . . _ 
enterthe year with 2digits. 
1811813 988 year 
,......-.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . until the desired 
month is 
displayed 
i . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . enter the day with 
1 or 2 digits 
.I . . . . . . . . . . . . . . . . . . ....

AB=[r)(Ol : speed access code 00 
. . . 
piE[ : 
speed access code 99 
: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CD= pj : automatic line access number 
MFi : access number of Trunk Group1 
dm : access number of Trunk Group8 
or 
;-‘--‘--.“.‘- until the desired speed access code (00 through 99) appears 
filfijI(NEXT~l~hone number I~MEMORY lm 
I 1 
Description 
100 system phone numbers can be stored with 
each number capable of storing 32 digits and 
may be accessed from any...

Conditions 
6. Press the MEMORY button. 
o The memory indicator will be lit. 
7. 
l To advance to the next speed access code, 
press the NEXT button. 
l To return to the previous speed access 
code, press the PREV button. 
l To go to the desired speed access code, 
press the SELECT button and then dial the 
speed access code. 
8. Repeat steps 4 to 7, to program the other 
phone numbers. 
9. To return to the initial program mode, press 
the END button. 
To change 
Repeat steps 1 to 9. 
To erase after...

Examples 
1) To enter trunk group access number 81 and telephone number 201-392-4.669 into speed access codeb0. 
(01 NEXT 09 8.1 201-392-4669 MEMORY END_) 
: : 
Speed access: Telephone 
code number 
Trunk’group 
access number 
l If punctuation is not entered in a phone number, the LCD will show as below 
( 00 : 812013924869 ) 
2) To enter automatic line access number 9, account code 1234 and telephone number 201-392-4669 into 
speed access code 02. 
(01 NEXT02 9 3c .x- 1234201-392-4669 MEMORY END) 
--_...

:..................,until the desired Jack number (01 through 32) appears 
i 
CDE=~1~1~~ : to assign phone number 100 
mmki : to assign phone number 199~  ,............................... 
. 
pzjliiEq NEiT IlCtrEll MEMORY lpiiq 
. 
4 I 
riiEdsE&m default 
is assigned to extension of Jack number 01 
132 is assigned to extension of Jack number 32 
I............................................ I AB=mo[ : to assign to Jack number 01 
I*[ : to assign to Jack number 32 
Description 
Enables programming of a 3...

-..........until the desired operator number (1 or 2) appears 
b 
.-.......... 
AB= mr[ : to assign extension (Jack no. 01) for Operator use 
m’k[ : to assign extension (Jack no. 32) for Operator use 
default ...... Nothing is stored 
Description 
Up to 2 of any extensions can be selected as the 
operator extensions. 
00 can be dialed to call operator 1, and 01 can be 
dialed to call operator 2. “CO Mode (Direct In Line) 
Assignment (on page 3-57)” can be used to program 
all incoming calls to be...

I.........,...... To activate an extension as a paired telephd&$f& console 1 
AB=[rin : extension (Jack number 01) 
n’E[ 
: extension (Jack number 32) 
To activate an extension as a paired telephone for console 2 
CD= mm : extension 
(Jack number 01) 
m.121: extension (Jack number 02) default  ...... 
lTiE[ : extension (Jack number 32) 
L7D~Ir~~l3nEl 04 NEXT NEXT A6 MEMORY NEXT CD MEMORY END 
Description 
The extension number paired with the DSS 
Console (KX-T123240) must be assigned when 
the DSS...