Panasonic Kx-T123211d Installation Manual

Card Installation 
1. To protect the printed circuit board from static 0 Insert the optional card with holding a levers of 
electricity, first discharge any body static by the card into the KX-T123211 surely. 
touching the metal board. Do not touch parts on the card. 
2. Loosen the screws to remove the metal board. 
3. The location of the optional cards for the 
KX-Tl23211 is shown in the following. 
(KX-T123292) 
$1 
l!h _ --__ I \ 
\ I I 
// / (KX-T123241)  metal board 
v 
Screws - 
0 
3 
P 
2 - 25  

OPTION (cont.) 
To add eight extensions (jack number 17 through 
24), use the optional expansion card 
KX-T123270. 
To add four extensions (jack number 17 through 
20), use the optional expansion card 
KX-T123271. 
1. Insert the expansion card KX-Tl23270 or 
KX-Tl23271 into the KX-Tl23211 
2. Insert connector to the KX-T123270 or 
KX-T123271 as shown at right. 
Cable Pin Numbers to be connected 
See page 2-10. 
0 Mis-connection may cause the KX-T123211 
to operate improperly. 
See “During Installation”...

To add four Central Office Lines (CO 9 
through 12), use the optional expansion 
card KX-Tl23280. 
1. 
2. 
. 
0 Insert the expansion card KX-T123280 into 
the KX-Tl23211. R : Ring 
T :Tip 
Vi 
ack (CO) 
Insert the modular plug of the telephone 
line cord (2-conductor wiring) into the 
modular jack on the KX-T123280. 
Mis-connection may cause the KX-T123211 
to operate improperly. 
See “During Installation” page 6-l and 
“During Connection” page 6-2 before 
connecting. 
To Terminal Board or Modular Jacks...

OPTION (cont.) 
When you remove the card, 
pull upward. 
To add four Central Office lines (CO5 through 8), 
use the optional expansion card KX-T123280. 
Insert the expansion card KX-T123280 into 
the KX-T123211. 
Insert the modular plug of the telephone 
line cord (2-conductor wiring) into the 
modular jack on the KX-T123280. 
Mis-connection may cause the KX-T123211 
to operate improperly. 
See “During Installation” page 6-l and 
“During Connection” page 6-2 before 
connecting. 
R : Ring 
T 
: Tip 
View...

To connect the optional DSS Console (KX-T123240 or KX-T61640), the optional DSS Console card (KX-T123241) 
is required. 
The DSS Console (KX-T123240 or KX-T61640) needs a paired Telephone (EMSS Proprietary Telephone) for 
proper operation, because the DSS console cannot work by itself. 
The EMSS Proprietary Telephone (such as KX-T123220, KX-T123230, KX-T123235, KX-T123250) is required as 
the paired telephone for dialing, storing, etc. 
Place the KX-T123240 or KX-T61640 and the paired telephone side by...

OPTION (cont.) 
Enables a standard telephone installed outside the premise to work as an extension through public orprivate lines. 
To avail of this feature, an optional Off Premise Extension Unit KX-T123286 is necessary aside from KX-T123285. 
1. Insert the Off Premise Extension Card 
KX-T123285 into the KX-T123211. 
2. Insert the connector from the KX-T123286 to 
the Off Premise Extension Card. Extension Card 
Connector 
(24 pin) 
 
3. 
n 
4. Connect the frame of the KX-T123286 to 
earth ground...

This feature enables to access System from outside of System and then call to extension or outside line. 
For example, you can call the desired extension directly by dialing the extension number following the regular CO 
number. 
Optional KX-T123292 card is necessary to program KX-T123211 to send Outgoing Message when called with this 
feature. 
1. Insert the Direct Inward System Access Cards A 
and B into the KX-T123211. 
“DISA-A” and “DISA-B” are written 
on each Card. Direct Inward System Access Cards...

OPTION (cont.) 
By using the data terminal connected to RS-232C on KX-T123211 or remote data terminal connected to KX-Tl23211 
through MODEM, diagnosis of KX-Tl23211 system can be done. 
Remote administration 
H The following optional cards are necessary. 
0 Diagnostic Card KX-T123295 
0 Direct Inward System Access Cards 
KX-T123291 
(See page 2-31) 
0 MODEM Card KX-T123296 
(See page 2-32) 
Data terminal equipment 
KX-Tl23211 
On-site administration 
RS232C Cable n The following card is necessary. 
0...

For installing the doorphone, use the Optional Doorphone Adaptor (Use the KX-T30860D only). 
Installation of the doorphone Installqtion of the Doorphone Adaptor 
Loosen the screw to 
separate the 
doorphone into 2 
halves. How to install the Doorphone Adaptor into the 
KX-Tl23211. 
1. Connect a 4-conductor modular connector to 
the doorphone adaptor. 
Install the lower case 
to the wall with 2 
screws. 
l 2 kinds of screws 
are included. Please 
choose according to 
your wall type. See 
the followings....

OPTION (cont.) 
(4 Connect the doorphone adaptor to the terminal box using a 4-conductor modular connector. 
(W Connect the wires of doorphone 1 to the red and green screws of the terminal box. 
(C) Connect the wires of doorphone 2 to the yellow and black screws of the terminal box. 
:or 
. 
Doorp 
0 
Doorphone Wiring 
hone 1 (KX-T30865) 
YELLOW 
RED Doorphone 2 (KX- 
BLACK 
GREEN ,T30865) 
The max. length of the telephone line cord (twisted cable) that connects the KX-T123211 and the doorphone...