Panasonic Kx-T123211d Installation Manual

;...“.‘........ until the desired jack number (01 through 32)appears. 
i........‘.‘.‘.‘............ until the desired mode appears 
Option 
.-.=*.....’ default(all 32 jack numbers) 
Forced 
J 
:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
: to assign the same on at132 jack numbers 
Description 
This feature gives each message of the SMDR 
to an account code of the called or calling party. 
This feature has two modes “Forced” and 
“Option” .In the “Forced” mode, the...

:......................-unti I the desired jack number (01 through 32) appears 
............................. until the desired mode appears 
Disable ..... ..-....defaul t (all 32 jack numbers) 
Enable I 
AB= El : to assign the same on all 32 jack numbers 
mm : on jack number 01 
]~j~[ : on jack number 32 
Description 
“Call Forwarding To Outside Line” (on page 7. Repeat steps 4 to 6 to program the 
4-29) enable for each extension. assignment of the other jack numbers. 
Programming 
1. 
2. 
3. 
4. Dial...

:...............- ............ until the desired jack number (01 through 32) appears 
i.. ........................... until the desired mode appears 
Disable .......... ..default(al I 32 jack numbers) 
Enable I 
: 
: to assign the same on all 32.jack numbers 
Description 
This feature can call to the extension that is setting 
the Do Not Disturb by programming. 
Refer to “Do Not Disturb Override” on page 4-32. 7. Repeat steps 4 to 6, to program the 
assignment of the other jack numbers. 
Programming...

Doorphone Feature 
_........................,............ until the desired doorphone number (1 or 2) appears’ 
,...............................,................... 
until the desired jack number appears 
m : on jack number 01 
m : on jack number 32 
m : to assign the same on all 32 jacks 
until the desired mode appears  . . ;) 
-------ea.default (all 32 jack numbers) 
Description 
Allows each extension to be programmed for 
receiving calls from up to 2 doorphones during 
the day or night mode....

.......................... until the desired mode appears 
Hold-l ......... ..Flas h hookswitch only ....................... . .. default 
Hold_2.. ......... 
Flash hookswitch and dial 20 
Description 
If the following happens frequently with a standard 
telephone, program the HOLD MODE 2. 
l Nobody answers when you receive a call. 
0 A CO line is busy although nobody is using 
the line. 
l The Trunk (CO) Indicator of the system unit 
does not turn off even after you hang up. 
If a call is not terminated...

l All Parameters 
0 System Parameter 
l Speed Dial ~.....‘...................................’ until the desired mode appears 
All 
Para . . . . . . . . . . . . . . . default 
System Para 
co Para 
: . EXT 
Para 
DSS Para 
Speed Dial 
bIE[ ISELECTI IMEMORY @iiiil 
t I 
l CO Parameter (Outside) 
:.................... until the CO Para appears 
: to assign the same on all 12 CO’s 
O~~nlQLgn 99 NEXT SELECT MEMORY AB MEMORY END 
l Extension Parameter 
:....................-until the EXT Para appears 
;.....

Description 
The system Data features are preset as the default 
data of the programming. 
All 
parameters 
System parameters 
CO parameters 
Extension parameters 
DSS parameters 
Speed dial 
System parameters 
Extension Number Assignment 
Operator Assignment 
Paired Telephone Assignment for 
DSS Console 
Automatic CO Hold Using DSS Button 
Day/Night Service Mode 
Call Hunting 
Toll Restriction 
Hold Time Reminder 
Hold Recall Time Set 
Transfer Recall Time 
Call Forwarding Starting Time 
Pickup Dial...

Programming 
To set System Parameters, Speed Dial or All 
Parameters to the default data 
; 
1. Dial (99). 
“System Clear” will be displayed. 
2. Press the NEXT button. 
“Menu : All Para” will be displayed and 
“All Para” will blink. 
3. Repeat pressing the SELECT button until the 
desired data mode is displayed. 
4. Press the MEMORY button. 
The LCD will stop blinking. 
5. Repeat steps 3 to 4, to clear the other system 
data. 
To set CO Parameter to the default data ; 
1. Dial (99). 
2. Press the NEXT...