Panasonic Kx P7305 Operating Instructions Manual

							Remote Control Panel
MacintoshBasics
Windows Windows36
MenuSelection 1 / InformationSelection 2
Quality Density Normal* (Lightest – Darkest)
Font Font Number 0* (0 – 54)
Font pitch 10.00* (0.44 – 99.99)
Font height 12.00* (4.00 – 999.75)
Symbol set PC8*
Network (KX-P7310 
only)MAC address xx:xx:xx:xx:xx:xx
Printer name KX-P7310-XXXXXX
Protocol (TCP/IP) On*
Off
DHCP On*
Off
IP address 0.0.0.0
Subnet mask (TCP/IP) 0.0.0.0
Gateway address 0.0.0.0
Protocol (Apple talk) On*
Off
Protocol (Netware) On*
Off
Protocol (SMB) On*
Off
Adjustment to Media Plain paper front side 0* (-3 – +3)
Plain paper back side 0* (-3 – +3)
Thick paper 0* (-3 – +3)
Cotton paper 0* (-3 – +3)
Transparency 0* (-3 – +3)
Label 0* (-3 – +3)
Envelope #10 0* (-3 – +3)
Envelope C5 0* (-3 – +3) 
						

							Remote Control Panel
MacintoshBasicsWindows
Windows37
MenuSelection 1 / InformationSelection 2
Others Power save mode 5* (2, 5, 10, 15, 30, 60)
Auto continues Off* On
Page Protection Off*
On
I/O timeout setting 60* (5 – 300)
Printer Emulation Auto*
PCL
Language English French
German
Italian
Spanish
Information Controller FW x.xx.xx Engine FW Vxxx
Page Styler2 x.xx.xx
Memory Size 16 MB (installed memory)
Option Cassette Not installed / Installed 
						

							Remote Control Panel
MacintoshBasics
Windows Windows38
■Paper
Paper Source
Selects the source feeding media. If the optional 2nd feeder is installed, Media tray will be 
changed to Upper and Lower selection is added.
Media type
Selects the type of media loaded in the media tray, manual feed and 2nd feeder (option). 
Media size
Selects the different media sizes.
Upper Tray / Lower Tray
Assigns the media size to the tray. The media can be fed from the tray corresponding to 
the paper size of the document. AutoSelect Tray must be selected for paper source to 
use the feature.
If an optional 2nd feeder is installed on the printer, these menus are displayed.
Lines per page
Sets the maximum number of text lines that are enabled to print on each page.
Copies
Sets the number of copies to be printed.
Orientation
Selects the print orientation.
Duplex
Selects either to Flip on long edge or to Flip on short edge when printing a document on 
both sides of paper.
Outline for Menus 
						

							Remote Control Panel
MacintoshBasics
Windows Windows39
Front Top Calibration
Adjusts the top margin of printing.
Front Left Calibration
Adjusts the left side margin of printing.
Back Top Calibration
Adjusts the back top margin of printing.
Back Left Calibration
Adjusts the back left side margin of printing.
■Quality
Density
Adjusts the density of printing. 
■Font
Font number
Selects a font to print by selecting the font number.
Font pitch
Selects the font pitch.
Font height
Selects the font height.
Symbol set
Selects a symbol set used for the selected font. A symbol set is a collection of alphabetic 
characters, punctuation marks, numeric and special symbols. 
						

							Remote Control Panel
MacintoshBasics
Windows Windows40
■Network (KX-P7310 only)
The network menu is displayed for the KX-P7310 only.
MAC address
Displays the MAC address. MAC address is a private number assigned to each network 
device.
Printer name
Displays the printer name.
Protocol (TCP/IP)
Enables TCP/IP by selecting On.
DHCP
Enables DHCP by selecting On. The printer’s IP address is assigned by the DHCP server 
on the network when the DHCP is enabled.
IP address / Subnet mask (TCP/IP) / Gateway address
Enables to manually set each item to use with TCP/IP.
Protocol (AppleTalk)
Enables AppleTalk by selecting On.
Protocol (Netware)
Enables Netware by selecting On.
Protocol (SMB)
Enables SMB by selecting On. 
						

							Remote Control Panel
MacintoshBasics
Windows Windows41
■Adjustment to Media
Print quality may vary do to moisture in the media. It enables adjustment to the printer’s 
setting corresponding to the condition of media. 
To get better print quality,
If media has high moisture, set it for + value (+1, +2 or +3).
If media has low moisture, set it for – value (–1, –2 or –3).
When performing duplex printing, set up Plain paper front side (side that prints first) and 
Plain paper back side (side that prints last). 
						

							Remote Control Panel
MacintoshBasics
Windows Windows42
■Others
Power save mode
To conserve energy and operating cost, this printer is provided with a programmable 
power save feature. The printer is factory set with the power save feature turned on to 
comply with E
NERGY STA R® requirement. The printer enters the Power Save mode when 
the printer is idle for 5 minutes by default.
Auto continues
With this feature turned on, the printer automatically continues the current print job in the 
case of certain non-fatal errors.
Page Protection
With this feature turned on, the printer does not begin printing until the processor has 
finished imaging the entire page. The page then prints correctly, although it takes slightly 
longer to print.
I/O timeout setting
Automatically prints the remaining data in memory when the computer does not send 
data to the printer during the set time.
Printer Emulation
Selects PCL or PostScript to print data.
•Auto: PCL or PostScript is Automatically selected depending on the print data.
•PCL: PCL is selected for printing.
NOTE
• If the PostScript emulation is not used, select PCL for the Printer Emulation. It will 
become difficult that the memory overflow error occurs.
Language
Selects the language when printing the configuration page [see “Tool Menus (Tool Bar 
Icons)” on page 32]. 
						

							Remote Control Panel
MacintoshBasics
Windows Windows43
■Information
Controller FW
Displays the controller firmware version.
Engine FW
Displays the engine firmware version.
Page Styler2
Displays the software version for PostScript.
Memory Size
Displays the total memory size installed in the printer.
Option Cassette
Displays whether the optional 2nd feeder has been installed. 
						

							Setting the Printer Driver
MacintoshBasics
Windows Windows44
It is possible to set the printer by using the printer properties window. It can be displayed from 
Windows (see below) or from an application (see page 46).
■Setting the Printer from Windows:
When setting the printer by using printer properties window under Windows, the setting is 
retained even if Windows is shutdown and restarted.
1Click [Start], move the pointer to Settings, then click Printers.
The Printers window is displayed.
• For Windows XP Professional / Windows Server 2003, click [Start], then click or 
double click Printers and Faxes.
• For Windows XP Home, click [Start], click Control Panel, click Printers and Other 
Hardware icon, then click Printers and Faxes icon.
2Click the Panasonic KX-P7305 PCL6, Panasonic KX-P7305 PS, 
Panasonic KX-P7310 PCL6 or Panasonic KX-P7310 PS icon.
3Click the File menu, then click the following menu depending on the 
operating system.
- Properties (Windows 95 / Windows 98 / Windows Me)
- Document Defaults... (Windows NT 4.0 )
- Printing Preferences... (Windows 2000 / Windows XP / Windows Server 2003)
The printer properties window is displayed.
Setting the Printer Driver
Displaying the Printer Properties Window
A 
						

							Setting the Printer Driver
MacintoshBasics
Windows Windows45
4Click a tab to view the features.
The explanation of the driver’s setting menu can be read by clicking it with the right
mouse button.
(tab in Windows 98)
• Tabs are different in Windows NT 4.0 / Windows 2000 / Windows XP / Windows 
Server 2003.
• For Windows NT 4.0 / Windows 2000 / Windows XP / Windows Server 2003, it 
enables you to set another items by selecting Properties of the File menu.