Panasonic Kx P7305 Operating Instructions Manual

							Troubleshooting
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.39
6Wipe the photosensitive drum with a dry cotton swab.
CAUTION
• Do not use a sharp-pointed something like a ball-point pen to prevent the damage to the 
drum unit when removing the paste.
7Insert the side pins of the toner cartridge into the slots of the drum unit 
(1). Push the toner cartridge in the drum unit (2).
Dust
Dust
Side pin1
2
2 
						

							Troubleshooting
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.40
8Firmly insert the drum unit in the slot of the printer (1) [insert the side pins 
of the drum unit into the groove (label  )]. Push down (2). 
9Close the front cover.
2
2
1
Side pin 
						

							Troubleshooting
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.41
1Open the front cover of the printer.
2Lift the drum unit up (1) and slide it out of the printer (2).
3Open the cover of the dust scraper.
4Clean the inside with the vacum cleaner, then close the cover of the dust 
scraper.
Cleaning the Dust Scraper
1
2
1 
						

							Troubleshooting
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.42
5Firmly insert the drum unit in the slot of the printer (1) [insert the side pins 
of the drum unit into the groove (label  )]. Push down (2). 
6Close the front cover.
2
2
1
Side pin 
						

							Error Indication
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.43
: Indicator is lit. : Indicator is blinking.
: Indicaator is turned off.
*1The status is varied depending on the condition.
Error Indication
IndicatorsError LEDPossible CauseRecovery
On: 0.5 sec.
Off: 0.5 sec.Front cover is open. Close the front cover.
RAM overflow or overrun has 
occurred.Press the PRINT/RESET 
button (less than 5 seconds).
On: 0.5 sec.
Off: 2 sec.Media jam has occurred. Remove the jammed media, 
then open the front cover and 
close it.
On: 1 sec.
Off: 0.5 sec.Manual feed is empty. Load media in the manual feed.
On: 1 sec.
Off: 1 sec.Media tray (standard) or lower 
tray (2nd feeder) is empty.Load media in the media tray 
(standard) or lower tray (2nd 
feeder).
Media tray (standard) is not 
installed.Install the media tray 
(standard).
Off Toner is low. Replace the toner cartridge 
soon.
Drum unit is wearing out. Replace the drum unit soon.
On: 0.5 sec.
Off: 0.5 sec.Drum unit is not installed. Install the drum unit.
Toner is empty. Replace the toner cartridge 
now.
Drum unit is worn out. Replace the drum unit now.
On Internal error has occurred. Turn the power off for a few 
seconds then on again. If the 
error continues, call for service.
READY
ERROR
TONER/
DRUM UNIT
*1READY
ERROR
TONER/
DRUM UNIT
READY
ERROR
TONER/
DRUM UNIT
READY
ERROR
TONER/
DRUM UNIT 
						

							Repacking Instructions
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.44
It is highly recommended that you keep the original carton and ALL packing materials. 
Should you need to transport or ship your printer, please follow these instructions.
SAFETY CAUTION
The printer weighs about 10 kg {22 lbs.}.
NOTE
• Should you need to send your printer for service, consult your reseller first or Panasonic.
• Please use the original carton and all of the original packing materials.
• Do not ship printer with drum unit installed.
• Improper repacking of the printer may result in a service charge to remove spilled toner.
• Since the printer uses dry toner, extreme care must be taken when handling. The printer 
should be handled in the upright (vertical) position.
Material required:
• Original cartons and packing materials
• Newspaper or drop cloth
• Shipping tape and scissors
1Turn off the printer; remove the power cord and all interface cables.
2Open the front cover.
Repacking Instructions
Repacking 
						

							Repacking Instructions
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.45
3Lift the drum unit up (1) and slide it out of the printer (2).
•To avoid possible toner spillage, it is recommended to place the drum unit on a news-
paper, drop cloth or best to place back in original (Black) shipping bag.
CAUTION
• To prevent any damage to the drum unit, observe the following precautions.
— Do not touch the drum surface illustrated below. 
— Do not expose the drum unit to light for more than 5 minutes.
— Do not expose the drum unit to direct sunlight.
— Do not keep the drum unit near dust or dirt.
— Do not place the drum unit in a high humid area.
1
2
1
Drum 
						

							Repacking Instructions
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.46
4While pushing the drum unit as illustrated below (1), lift the toner 
cartridge up (2).
5Replace the shipping cover on the toner cartridge.
2
1 
						

							Repacking Instructions
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.47
6Insert the toner cartridge into a plastic bag and certainly seal the end of 
the bag tightly.
7Wrap the drum unit with the protective sheet to protect the drum surface.
8Insert the drum unit into a plastic bag and seal the end of the bag tightly.
9Close the front cover. 
1
23 
						

							Repacking Instructions
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.48
10Wipe off any loose toner in and around the printer.
NOTE
• If a toner vacuum is available, it is the best tool for cleaning spilled toner. Do not use a 
standard office vacuum; the toner will not be retained by typical vacuum dust collectors.
11Repack the printer.
Toner cartridge
Power cordDrum unit
Printer CD-ROM
Setup Guide