Panasonic Kx P7305 Operating Instructions Manual

							Settings and Printing
Network Network Maintenance and Spec.
Appendix
88
■Troubleshooting when installing the printer software
TroublePossible CauseCorrective Action
Printer software cannot be 
installed in a computer.You do not log on the 
computer as an 
Administrator in Windows 
NT 4.0, Windows 2000, 
Windows XP or Windows 
Server 2003.Log on the computer as an 
Administrator.
A document is not printed 
through the server 
computer.You have no authority to 
print.Contact the administrator to 
register you.
You are not registered in 
the server.
The administrator’s 
password is required 
when restarting the 
computer.You cannot install the 
printer software. Install the printer software as 
an Administrator.
The printer CD-ROM disk 
may be required when 
modifying or repairing the 
installed printer software 
after installing the printer 
software with the shared 
folder of the server 
computer.The server computer is 
turned off.Turn on the server computer to 
share the folder for the 
installation program.
The server computer is 
disconnected from the 
network.Connect the server computer to 
the network.
Network problems occur. Consult with the network 
administrator. 
						

							Settings and Printing
Network Network Maintenance and Spec.
Appendix
89
•General(see below)
•TCP/IP(see page 90)
•NetWare(see page 91)
•AppleTalk(see page 92)
•SMB(see page 92)
•SNMP(see page 93)
•Printer Port(see page 94)
■General
Configuration Parameters
NameFactory DefaultDescription
Change root 
passwordNULL Password for Administrator. It is used for 
authentication when entering Network 
Setup Tool.
Use HP JetAdmin ENABLE Enables or disables to use HP's utility 
JetAdmin/Web JetAdmin. 
						

							Settings and Printing
Network Network Maintenance and Spec.
Appendix
90
■TCP/IP
NameFactory DefaultDescription
Use TCP/IP Protocol ENABLE Enables or disables TCP/IP protocol.
Use DHCP/BOOTP ENABLE Enables or disables DHCP/BOOTP. When 
enabled, KX-P7310 gets an IP Address 
from the DHCP/BOOTP server while 
booting. To use this function DHCP/BOOTP 
server must exist on the network.
Use RARP ENABLE Enables or disables RARP. RARP is a 
protocol which obtains IP Address from 
RARP server. When using this function, a 
RARP server must exist on the same 
network.
IP Address 0.0.0.0 IP Address for the network in which the KX-
P7310 is installed.
Subnet Mask 0.0.0.0 Subnet mask for the network in which the 
KX-P7310 is installed.
Default Gateway 0.0.0.0 IP Address of the default gateway through 
which systems on other networks can be 
reached.
WINS Server - 
Primary (Preferred) 
WINS Server0.0.0.0 Sets the WINS server (primary) address. 
The Computer Name of the NetBEUI/
NetBIOS is used for NETBIOS name.
WINS Server - 
Secondary 
(Alternate) WINS 
Server0.0.0.0 Sets the WINS server (secondary) address.
The Computer Name of the NetBEUI/
NetBIOS is used for NETBIOS.
WINS Server - 
Scope IDNULL Sets Scope ID.
Use IP Filtering DISABLE Enables or disables IP Filtering.
Filter Mode ACCEPT Sets the mode of the IP Filtering: DENY or 
ACCEPT.
Filter1 / Filter2 / 
Filter3 / Filter40.0.0.0 Sets the range of IP addresses for IP 
Filtering.
Use IPv6 Protocol DISABLE Enables or disables IPv6 protocol.
Use FTP/LPD 
BannerDISABLE Prints a banner page when using LPR 
printing. 
						

							Settings and Printing
Network Network Maintenance and Spec.
Appendix
91
■NetWare
NameFactory DefaultDescription
Use NetWare 
ProtocolENABLE Enables or disables NetWare printing.
Frame Type 802.2 Sets default Frame type used by KX-P7310. 
If KX-P7310 does not work with the frame 
type, it will be automatically changed to 
different type.
Printer  Name MLPxxxxxx-Printer Sets printer name registered to the NetWare 
server. This name must be same as the 
printer name registered to the NetWare 
server.
Operation Mode PSERVER Sets operation mode (PSERVER or 
RPRINTER). If KX-P7310 does not work 
with the current operation mode, it will be 
automatically changed to different mode.
Print Server Name MLPxxxxxx Sets a print server name for PSERVER 
mode.
Password NULL Sets a password to log on the file server.
Job Polling Time 4 seconds Sets the interval to log on the file server.
Bindery Mode ENABLE Enables or disables Bindery mode.
File Server Name NULL You may set the name of the file server (up 
to 8 servers).
NDS Tree NULL Sets the NDS tree. Normally, KX-P7310 will 
automatically detect the tree name.
However, when there are several trees 
within the network, you must set the name.
NDS Context NULL Sets the context used by NDS in the print 
server name.
Print Server Name NULL You may set the print server name (up to 8 
servers) to which the KX-P7310 is 
connected.
Time Out 10 seconds A time for KX-P7310 to recognize the end of 
a job in remote printer mode. 
						

							Settings and Printing
Network Network Maintenance and Spec.
Appendix
92
■AppleTalk
■SMB
NameFactory DefaultDescription
Use AppleTalk 
ProtocolENABLE Enables or disables AppleTalk protocol for 
KX-P7310. 
Printer Name KX-P7310-xxxxxx Sets the AppleTalk printer name. The name 
set here can be seen from Chooser.
Zone Name * Sets zone name to which KX-P7310 
belongs. If blank, KX-P7310 will 
automatically belong to the zone name 
where the AppleTalk router is set.
NameFactory DefaultDescription
Use NetBEUI 
ProtocolENABLE Enables or disables NetBEUI protocol.
Use NetBIOS over 
TCP/IPENABLE Enables or disables NetBIOS protocol.
Computer Name MLPxxxxxx Sets Computer name. This name is shown 
as the computer in Windows Explorer.
Workgroup MLP-Printer Sets the workgroup the KX-P7310 belongs 
to.
Comment NULL This comment is shown as the computer in 
Windows Explorer.
Activate Master 
Browse FunctionENABLE Enables or disables master browse function. 
						

							Settings and Printing
Network Network Maintenance and Spec.
Appendix
93
■SNMP
NameFactory DefaultDescription
Authentic 
Community****** Sets SNMP authentic community name. 
This community name is authenticated 
when receiving SNMP Set Request.
Use Authentic Trap DISABLE Enables or disables authentic TRAP.
TRAP Community public Enters TRAP community name. This name 
will be used when the printer executes a 
TRAP.
TRAP Address 0.0.0.0 Enters the TRAP address. The TRAP 
address is disabled if the IP Address is set 
0.0.0.0.
SysContact NULL Enters SysContact for MB-II object. 
Normally enter the administrator’s mail 
address.
SysName NULL Enters SysName for MB-II object. Normally 
enter the host name or domain name.
SysLocation NULL Enters SysLocation for MB-II object.
Normally enter where the printer is located. 
						

							Settings and Printing
Network Network Maintenance and Spec.
Appendix
94
■Printer Port
NameFactory DefaultDescription
lp Port
BOJ String 
(MJL String)NULL Sets the MJL String that will be sent before 
sending a print job to the direct output port 
(lp).
EOJ String 
(MJL String)NULL Sets the MJL String that will be sent at the 
end of a print job to the direct output port 
(lp).
euc/sjis Port
BOJ String NULL Sets the string sent before sending the 
printing job to the output port via Kanji filter 
(sjis, euc).
EOJ String \f Sets the string that will be sent at the end of 
the printing job to the output port via Kanji 
filter (sjis, euc).
Printer Emulation ASCII Sets printer emulation (PDL). Changes to 
appropriate code when printing via Kanji 
filter (sjis, euc).
Tab Size 8 char Sets the number of spaces that correspond 
to 1 tab. All tab codes will be converted to 
the spaces according to the number set 
here. This feature will not be available when 
this is set to "0" or when the job is directly 
sent to the printer.
Page Width 0 char Sets the number of characters for the auto 
line feed feature of the Kanji filter. The auto 
line feed feature is not available when this is 
set to "0".
Page Length 0 line Sets the number of lines for auto page feed 
feature of the Kanji filter between the 
number 0-255. The auto page feed feature 
is not available when this is set to “0”.