Panasonic Kx P7305 Operating Instructions Manual

							Specifications
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.49
Printing Method:
Semiconductor Laser
Print Speed:
18 ppm (pages per minute) maximum (A4 size plain paper, simplex printing, 5% image area)
19 ppm maximum (Letter size plain paper, simplex printing, 5% image area)
9 ppm (pages per minute) maximum (A4 size plain paper, duplex printing, 5% image area)
9.5 ppm maximum (Letter size plain paper, duplex printing, 5% image area)
Resolution:
300 x 300 dpi (dots per inch), 600 x 600 dpi, 1200 x 600 dpi
NOTE
• It is recommended to install the memory board option KX-PEM12 or KX-PEM13 if printing in 
1200 x 600 dpi.
Paper Feed:
Media tray (universal cassette): up to 250 sheets of paper [75 g/m
2 (20 lb.)]
Manual feed: 1 sheet
2nd feeder (option): up to 550 sheets of paper [75 g/m
2 (20 lb.)]
Paper Output:
Up to 150 sheets of paper [75 g/m
2 (20 lb.)]
Power Source:
Refer to the nameplate on the rear of the unit
Memory:
16 MB
Emulation:
PCL 6 Emulation*
1, PostScript® 2 Emulation*1
*1The available fonts or print may differ from the genuine software because they are not 
genuine software of HP or Adobe.
Specifications
Printer 
						

							Specifications
Settings and Printing NetworkMaintenance and Spec.
Maintenance and Spec.50
Interface:
Parallel (IEEE1284), USB (Hi-Speed USB 2.0), 
Ethernet (100Base-TX / 10Base-T) - KX-P7310 only
Warm Up Time
15 seconds [at 22°C (71.6°F), 50% RH]
Operating Environment:
10 to 32.5°C (50 to 90.5°F), 20 to 80% RH
Storage Environment:
0 to 35°C (32 to 95°F), 10 to 80% RH
Dimensions:
399 (W) X 390.5 (D) X 254 (H) mm (15.7
″ X 15.4 ″ X 10 ″)
Mass {Weight}:
Approx. 10 k g {22 lbs.}
Consumables / Life:
Starter toner cartridge (provided with printer); 2,000 pages average*
1
Toner cartridge; 5,000 pages average*1 (6,000 pages maximum)
Drum unit; 20,000 pages average*1
*1Average life at 5 % image area with repetitive printing of 10 pages (Letter / A4 size, single-
sided printing, default density).
The maximum life of the toner cartridge will not exceed 6,000 pages.
5% image area means that the black area within the printing area is 5%. Printing 10% 
image area continuously will reduce the life of  the toner to about half as compared to 
printing 5% image area.
Power Consumption:
Printing (average)*
2: 330 W
Standby (average):  70 W
Power saving (When the fan stops.): 10.5 W or less
*
2 Maximum print speed, duplex printing
Meets E
NERGY STA R® power conservation requirements.
Noise Level:
Printing: 51 dBA (average)
Standby: 29 dBA (average)
CPU:
NEC V850E1 
						

							Specifications
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.51
The following fonts can be used as the printer’s resident fonts. You can print the list of 
available fonts from the Remote Control Panel in Windows. See “Remote Control Panel” on 
page 28 in “Windows” of “Settings and Printing”. 
NOTE
• All printer’s resident fonts have also been included in the printer CD-ROM. For information on 
how to install these fonts on your computer, see the Setup Guide.
■TrueType Font for PCL
The following 45 fonts can be available.
•Dutch
TM 801 SWC, Dutch 801 Italic SWC, Dutch 801 Bold SWC, Dutch 801 Bold Italic SWC
•Swiss
TM 742 SWC, Swiss 742 Italic SWC, Swiss 742 Bold SWC, Swiss 742 Bold Italic SWC, 
Swiss 742 Condensed SWC, Swiss 742 Condensed Italic SWC, Swiss 742 Condensed Bold 
SWC, Swiss 742 Condensed Bold Italic SWC
• Incised 901 SWC, Incised 901 Italic  SWC, Incised 901 Bold SWC
• Zapf Humanist 601 SWC, Zapf Humanist 601 Italic SWC, Zapf Humanist 601 Bold SWC, 
Zapf Humanist 601 Bold Italic SWC
• Aldine 430 Original Garamond SWC, Aldine 430 Original Garamond Italic SWC, Aldine 430 
Original Garamond Bold SWC, Aldine 430 Original Garamond Bold Italic  SWC
• Fixed Pitch 810 Courier Roman SWC, Fixed Pitch 810 Courier Bold SWC, Fixed Pitch 810 
Courier Italic SWC, Fixed Pitch 810 Courier Bold Italic SWC
• Fixed Pitch 850 Letter Gothic 12 pitch/text SWC, Fixed Pitch 850 Letter Gothic Bold 12 pitch/
text SWC, Fixed Pitch 850 Letter Gothic Italic 12 pitch/text SWC
• Flareserif 821 SWC, Flareserif 821 Extra Bold SWC
• Clarendon 701 Clarendon Condensed SWC
• Ribbon 131 SWC
• Audrey Two SWC
• Swiss 721 SWM, Swiss 721 Oblique SWM, Swiss 721 Bold SWM, Swiss 721 Bold Oblique 
SWM
• Dutch 801 SWM, Dutch 801 Italic SWM, Dutch 801 Bold SWM, Dutch 801 Bold Italic SWM
• Symbol SWA
• Wingbats SWM
Fonts 
						

							Specifications
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.52
■Fonts for PostScript
The following 35 fonts can be available.
• Dutch 801 SWA, Dutch 801 Bold SWA, Dutch 801 Italic SWA, Dutch 801 Bold Italic SWA
• Swiss 721 SWA, Swiss 721 Bold SWA, Swiss 721 Oblique SWA, Swiss 721 Bold Oblique 
SWA
• Fixed Pitch 810 Courier SWA, Fixed Pitch 810 Courier Bold SWA, Fixed Pitch 810 Courier 
Italic SWA, Fixed Pitch 810 Courier Bold Italic SWA
• Symbol SWA
• Century 702 Century Schoolbook SWA, Century 702 Century Schoolbook Italic SWA, 
Century 702 Century Schoolbook Bold SWA, Century 702 Century Schoolbook Bold Italic 
SWA
• Revival 711 ITC Bookman Light SWA, Revival 711 ITC Bookman Demi Italic SWA, Revival 
711 ITC Bookman Demi Bold SWA, Revival 711 ITC Bookman Demi Bold Italic SWA
• Swiss 721 Narrow Bold SWA, Swiss 721 Narrow Bold Oblique SWA, Swiss 721 Narrow 
SWA, Swiss 721 Narrow Oblique SWA 
• Geometric 711 ITC Avant Garde Gothic Book SWA, Geometric 711 ITC Avant Garde Gothic 
Book Oblique SWA, Geometric 711 ITC Avant Garde Gothic Demi SWA, Geometric 711 ITC 
Avant Garde Gothic Demi Oblique SWA
• Chancery 801 ITC Zapf Chancery Medium Italic SWA
• ITC Zapf Dingbats SWA
• Zapf Calligraphic 801 SWA, Zapf Calligraphic 801 Bold SWA, Zapf Calligraphic 801 Italic 
SWA, Zapf Calligraphic 801 Bold Italic SWA 
						

							Specifications
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.53
■Paper Specifications
This printer is designed to work well with most types of paper. However, differences in paper 
may have significant effects on the quality of the print or the reliability of paper handling. It is 
strongly recommended that you always test paper before purchasing it to make sure it 
provides desirable performance. The following guidelines will be helpful.
Basic Weight:
60 to 105 g/m
2 (16 to 28 lb.)
Thickness:
3.7 to 7.5 mils (1 mil=1/1000″)
Moisture Content:
4% to 6%
Smoothness:
100 to 300 Sheffield
Acid Content:
5.5 PH minimum
Fusing Compatibility:
Must not scorch, melt, offset material, or release hazardous emissions when heated to 200°C 
(392°F) for 0.1 second
Cutting Dimensions:
±0.0313 inch of nominal, corners 90°±4°
Grain:
Long grain
Cut Edge Conditions:
Cut with sharp blades, no paper dust
Ash Content:
Not to exceed 10%
Curl:
No allowable curl toward the side to be printed
Packing:
Polylaminated moisture proof ream wrap
Media 
						

							Specifications
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.54
NOTE
• Please store your paper according to the recommendations of the manufacturer.
■Paper and Envelope Sizes
The following paper and envelope sizes are supported by the printer.
*
1 Duplex printing cannot be performed with A5, A6 size paper or envelope.
MediumNameDimension
PaperLetter 216 x 279 mm (8.5″ x 11″)
A4 210 x 297 mm (8.27″ x 11.7″)
Legal 216 x 356 mm (8.5″ x 14″)
B5 176 x 250 mm (6.92″ x 9.84″)
Executive 184 x 267 mm (7.25″ X 10.5″)
A5*
1148.5 x 210 mm (5.85″ x 8.27″)
A6*
1105 x 148.5 mm (4.13″ x 5.85″)
Envelope*
1Envelope #9 98 x 225 mm (3.87″ x 8.87″)
Envelope #10 105 x 241 mm (4.12″ x 9.5″)
International DL 110 x 220 mm (4.33″ x 8.66″)
International C5 162 x 229 mm (6.38″ x 9.01″)
Monarch 98 x 191 mm (3.87″ x 7.5″) 
						

							Specifications
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.55
■Types of Paper to Avoid
• Extremely smooth or shiny paper or paper that is highly textured 
• Coated papers
• Acid paper
• Letterhead imprinted with low temperature or thermography. These materials may transfer 
onto the fusing roller and cause damage. Any pre-printed paper should use inks compatible 
with 200°C (392°F) for 0.1 second.
• Damaged or wrinkled paper, or paper with irregularities such as tabs, staples, etc.
• Multipart forms or carbonless paper
• Paper with a cotton and/or fiber content over 25%
•Ink jet media (paper, transparency, etc.) (It may transfer onto the fuser unit’s roller and cause 
damage.)
■Transparencies and Labels
You may also print on labels and transparencies that are made for the printer. Panasonic has 
tested and found that the following work satisfactorily.
OHP transparencies3M CG3300
Labels  AVERY 5160, AVERY 5161, AVERY 5162, AVERY 5163, 
AVERY 5660, AVERY 5661, AVERY 5662, AVERY 5663
Avery L7159, Avery L7160, Avery L7161, Avery L7162,
Avery L7163, Avery L7164
• To avoid damaging the printer, do not use ink jet transparency.
• Transparencies and adhesive material of labels should be stable at 205°C (400°F), the 
printer’s maximum temperature.
• Re-using transparencies that have been fed through the printer once (for example, after jams 
or if the transparency is ejected without being printed) can reduce the life of the consumables 
and paper path components.
• When using transparencies, if the print quality is poor, print on the other side. 
						

							Specifications
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.56
NOTE
• With any label stock, the labels must completely cover the backing material (see figure 
below).
■Envelope Specifications
It is recommended that you purchase only high quality envelopes with diagonal seams, as 
shown in the diagram below:
High quality envelopes have the following characteristics:
• A thin, sharply creased leading edge
• Paper weight of 90 g/m
2 (24 lb.)
• Flat, free of curls, wrinkles, nicks, etc.
NOTE
• Wrinkle may occur in some case, even if high quality envelopes are used.
NOYES
Labels cover the entire
backing materialThe backing material is exposed. 
						

							Specifications
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.57
It is not recommended that you use envelopes with any of the following characteristics (using 
these may result in paper jams):
• Irregularly shaped envelopes
• Envelopes with curls, wrinkles, nicks, twists, dog-ears or other damage
• Envelopes with side seam construction
• Highly textured envelopes, or with extremely shiny surfaces
• Envelopes that seal by removing a peel-off strip
• Envelopes with more than one flap to be sealed
• Self-adhesive envelopes
• Envelopes that are baggy or not sharply creased
• Embossed envelopes
• Envelopes that have previously been printed with a laser printer
• Envelopes that have been previously printed inside
Side seam
construction
Peel-off stripMultiple flaps Twist
CurlBent-edge
Wave Dog-ears
Self adhesive 
						

							Specifications
Settings and Printing Network
Maintenance and Spec. Maintenance and Spec.58
Do not attempt to print on any of the following types of envelopes. These may cause damage 
to your printer.
• Envelopes with clasps, snaps or tie strings (see Figure 1)
• Envelopes with transparent windows (see Figure 2)
• Envelopes that will melt, discolour, scorch, offset or release hazardous emissions when 
exposed to 200°C (392°F) for 0.1 second
• Envelopes that use encapsulated types of adhesive that do not require moistening but rely on 
pressure to seal them
Always test a sample of the envelopes you are thinking of buying. Confirm that the envelope 
performs acceptably.
For best printing results
• Avoid printing in high humidity i.e., above 70%. 
High humidity may cause the envelope to curl and pick up excess toner.
High humidity may also cause the envelope to seal.
• Envelope storage is very important. Store them away from moisture and humid air, where 
they can lay flat and their edges won’t be bent or damaged. The humidity should not exceed 
70% RH.
Figure 1
Figure 2