Panasonic Kx P7305 Operating Instructions Manual

							Settings and Printing
Network Network Maintenance and Spec.
Setup in NetWare
48
[A] Using NDS - PSERVER mode
The following are the steps for setting up the printer. First install the Network Setup Tool from 
the printer CD-ROM disk and then set up the printer.
1Start the server system.
2Start the client system and log on the network in the NDS mode.
• If the Network Setup Tool is already installed, click [Start], move the pointer to 
Programs or All Programs, Panasonic and Panasonic KX-P7305 and KX-P7310, 
then click Network Setup Tool. Proceed to step 7.
3Insert the printer CD-ROM disk into the CD-ROM drive.
The CD-ROM launches automatically.
NOTE
• If the CD-ROM does not launch automatically, perform the following steps.
(1) Double click My computer icon (Windows XP / Windows Server 2003: Start - My 
Computer).
(2) Double click the CD-ROM icon.
4(Click language and) click KX-P7310.
5Click Install Network Utilites.
6Follow the instructions until the screen below is displayed. 
						

							Settings and Printing
Network Network Maintenance and Spec.
Setup in NetWare
49
7Click on the Ye s check button, and then [Finish].
A list of printers residing on the network is displayed.
• If you want to search the network for printers again, click the Device menu and select 
Search.
8Select the printer you want to set up from the list. Then click the Setup 
menu and select Network Setup....
NOTE
• When several printers are listed in the Network Setup Tool window, select the printer 
using the MAC address. You can obtain the number (hexadecimal six digits) from the 
label near the network interface connector or by printing a configuration page (press 
PRINT/RESET button more than 2 seconds and less than 5 seconds).
• If a password is set in the printer, you must enter the password and click [OK]. If a 
password is not entered, you can still see the printer's setting by checking on the 
Guest user check box, but you cannot change it. To set a password, refer to “Setting 
Password with Network Setup Tool” on page 81. 
						

							Settings and Printing
Network Network Maintenance and Spec.
Setup in NetWare
50
9Click the NetWare tab.
NOTE
• You can change the Print Server Name and Printer Name. After changing, click [OK]. 
Then go back to the step 8.
10Click on the PSERVER Mode check button.
11Click [OK].
12If you change the setting, click [OK], then click [Yes].
The following are the steps to set up the server.
13Select the printer you want to configure in the Network Setup Tool 
window.
14Click the Setup menu and select Create NetWare Queue.
15Follow the instructions on the screen.
When asked to select NDS mode or Bindery mode, select NDS Mode and click 
[Next >]. 
						

							Settings and Printing
Network Network Maintenance and Spec.
Setup in NetWare
51
16Expand the Tree and select the context where the Queue will be added, 
and click [Next >].
17Click on the Print Server Mode check button and click [Next >]. 
						

							Settings and Printing
Network Network Maintenance and Spec.
Setup in NetWare
52
18Change the queue name if needed. The print jobs are temporarily stored 
on the selected volume; if there is different volumes required select it from 
the list, then click [Next >].
19Follow the instructions on the screen.
NOTE
• When the setting is finished, the printer is automatically restarted. 
						

							Settings and Printing
Network Network Maintenance and Spec.
Setup in NetWare
53
[B] Using NDS - RPRINTER (NPRINTER) mode
The following are the steps to set up the printer. First install the Network Setup Tool by using 
the printer CD-ROM disk and then set up the printer.
1Start the server system.
2Start the client system and log on the network in the NDS mode.
• If the Network Setup Tool is already installed, click [Start], move the pointer to 
Programs or All Programs, Panasonic and Panasonic KX-P7305 and KX-P7310, 
then click Network Setup Tool. Proceed to step 7.
3Insert the printer CD-ROM disk into the CD-ROM drive.
The CD-ROM launches automatically.
NOTE
• If the CD-ROM does not launch automatically, perform the following steps.
(1) Double click My computer icon (Windows XP / Windows Server 2003: Start - My 
Computer).
(2) Double click the CD-ROM icon.
4(Click language and) click KX-P7310.
5Click Install Network Utilites.
6Follow the instructions until the screen below is displayed. 
						

							Settings and Printing
Network Network Maintenance and Spec.
Setup in NetWare
54
7Click on the Ye s check button, and then click [Finish].
The list of printers residing on the network is displayed.
• If you want to search the network for printers again, click the Device menu and select 
Search.
8Select the printer you want to set up from the list. Then click the Setup 
menu and select Network Setup....
NOTE
• When several printers are listed in the Network Setup Tool window, select the printer 
using the MAC address. You can obtain the number (hexadecimal six digits) from the 
label near the network interface connector or by printing a configuration page (press 
PRINT/RESET button more than 2 seconds and less than 5 seconds).
• If a password is set in the printer, you must enter the password and click [OK]. If a 
password is not entered, you can still see the printer's setting by checking on the 
Guest user check box, but you cannot change them. To set a password, refer to 
“Setting Password with Network Setup Tool” on page 81. 
						

							Settings and Printing
Network Network Maintenance and Spec.
Setup in NetWare
55
9Click the NetWare tab.
NOTE
• You can change the Print Server Name and Printer Name. After changing, click [OK]. 
Then go back to the step 8. 
						

							Settings and Printing
Network Network Maintenance and Spec.
Setup in NetWare
56
10Click on the RPRINTER Mode check button.
11Click [OK].
12If you change the setting, click [OK], then click [Yes].
The printer is restarted.
The following are the steps to set up the server.
13Select the printer you want to configure from the list. Click the Setup 
menu and select Create NetWare Queue.
14Follow the instructions on the screen.
• When asked to select NDS or Bindery mode, select NDS Mode and click [Next >]. 
						

							Settings and Printing
Network Network Maintenance and Spec.
Setup in NetWare
57
15Expand the Tree and select the context where the Queue will be added, 
and click [Next >].
16Click on the Remote Printer Mode check button and click [Next >].