Panasonic Aj Lt95 Operating Instructions Manual
Here you can view all the pages of manual Panasonic Aj Lt95 Operating Instructions Manual. The Panasonic manuals for Laptop are available online for free. You can easily download all the documents as PDF.
Page 61
61 Editing without setting the edit IN point (park & edit) Editing can be performed without setting the VTR1 and VTR2 IN points. 1Operate VTR1 and VTR2, and locate the places which will serve as the IN points. 2Press the PREVIEW button. The position where the PREVIEW button was pressed is automatically set as the edit IN point, and preview is executed. When the OUT points have not been set either, press the MARK OUT button during the preview at the place which is to serve as the OUT point. The position...
Page 62
62 Still-picture editing/slow-motion editing 1Set the IN point and OUT point of VTR1 (player) at the same position. After VTR1 has been selected using the VTR1 button, press the MARK IN and MARK OUT buttons together to set the IN point and OUT point at the same position. 2Select VTR2 using the VTR2 button, and set the IN point and OUT point of VTR2 (recorder) respectively. Even when only the IN point is set, open-ended editing is possible. 3Select VTR1 (player), and turn the search dial to run the tape...
Page 63
63 Voice-over operations (1) 1Select “INT_V0” as the setup menu item No.317 (AUD MEM MODE) setting. “m” now appears on the superimposed display of VTR2. (See page 85) 2Select the channel (CH1, CH2) for recording the sound with the setup menu item No.318 (AUD MEM CH) setting. 3Connect the audio signals which are to be recorded. When connecting a microphone, connect it to CH2 on the VTR2 side (the second AUDIO IN connector from the left as seen from the rear panel). 4Set the VTR2 AUDIO INPUT selector...
Page 64
64 AUDIO MONITOR SELECTLR CH 1 4 1 3MIXANALOGMIX2 UNIV2 PB SDI REC VA R CH 2 CH 3 CH 4 CH 3 44(V1·2) V1 V21 3MIX MIX24 1 3MIX MIXASMBL VA1 A21ST EDITPREVIEW VTR 2 VTR 1 SPLIT MARK OUT MARK IN SHIFT ENTERALL STOP REVIEWAUTO EDITMULTIGO TOGO TO OUTDURTOTALOUTLAST EDINLAST XEVENT 789 456 12 0C3~-+ DELETE SET UP F/TC DIAG LISTCORCT BS TRACKDUMPLOAD FSDISPEXIT RETURN T SET PLAYSTOPSTILL REW FFSTB OFF A3A4TCREC EDIT24 1 3MIX MIX24 1 3MIX MIX24 1 3MIX MIX2SDI CH 1 CH 2V2/ V1 PBRECCH 3 CH 4 INTANALOGSDI10 10...
Page 65
65 Voice-over operations (2) 1Select “INT_VO” as the setup menu item No.317 (AUD MEM MODE) setting. “m” now appears on the superimposed display of VTR2. (See page 85) 2Select the channel (CH1, CH2) on which the sound is to be recorded with the setup menu item No.318 (AUD MEM CH) setting. 3Connect the audio signals which are to be recorded. When connecting a microphone, connect it to CH2 on the VTR2 side (the second AUDIO IN connector from the left as seen from the rear panel). 4Set the VTR2 AUDIO INPUT...
Page 66
66 Audio cross channel editing Sound can be recorded on CH1 and CH2 channels only. Audio cross channel editing using the internal audio memory can be performed by connecting an external audio mixer. $Example of operation Recording cross-faded audio signals onto CH2 Process 1 AJ-LT95 VTR1 VTR2INPUT A INPUT BMIXER CH1 OUT MIXER CH2 OUT AUDIO CH1 OUT Internal memory AUDIO OUT (CH1 or CH2)AUDIO CH2 INAUDIO CH1 IN Audio mixer INPUT A INPUT BMIXER CH1 OUT MIXER CH2 OUT Audio mixer 1 2 Select CH2 as the setup...
Page 67
67 Audio cross channel editing AJ-LT95 VTR1 VTR2INPUT A INPUT BMIXER CH1 OUT MIXER CH2 OUT AUDIO CH1 OUT Internal memory AUDIO OUT (CH1 or CH2)AUDIO CH2 INAUDIO CH1 IN Audio mixer INPUT A INPUT BMIXER CH1 OUT MIXER CH2 OUT Audio mixerINPUT A INPUT BMIXER CH1 OUT MIXER CH2 OUT Audio mixer INPUT A INPUT BMIXER CH1 OUT MIXER CH2 OUT Audio mixer Cross-fading Process 2 1Press the A1 button and turn off its lamp. The A2 button LED remains lighted. (CH1 audio insert is released and only CH2 audio insert...
Page 68
68 Audio cross channel editing Step 1 (event 1) CH1IN pointOUT point OUT point Internal memory Approx. 20 sec Internal memory Approx. 20 sec To step 3 (event 3) CH2 IN point Cross-fading by operating the audio mixerCH1 insert start Portion recorded in step 1 Signals from the internal memory recorded hereSignals from VTR1 (player) recorded here CH2 Step 2 (event 2) CH1 CH2 5In order to perform the next audio cross channel editing operation (next event), press the A1 button to start the CH1 insert editing...
Page 69
69 Checking the edit points (IN, OUT, DUR, GO TO) $Checking the edit IN point setting (IN) Press the IN button. While holding down this button, the VTR1 IN point data is shown on the VTR1 counter, and the VTR2 IN point data is shown on the VTR2 counter. $Checking the edit OUT point setting (OUT) Press the OUT button. While holding down this button, the VTR1 OUT point data is shown on the VTR1 counter, and the VTR2 OUT point data is shown on the VTR2 counter. $Checking the editing duration setting (DUR)...
Page 70
70 Modifying and clearing edit data $Modifying edit points (IN point, OUT point or duration) one frame at a time (trimming) OTo increase the edit IN point by one frame, press the + button while holding down the IN button. OTo decrease the edit IN point by one frame, press the – button while holding down the IN button. OTo increase the edit OUT point by one frame, press the + button while holding down the OUT button. OTo decrease the edit OUT point by one frame, press the – button while holding down the...