Panasonic Aj Lt95 Operating Instructions Manual

11
Counter display area
E
Event number display lamps
This unit controls up to 200 sets of edit data (001 to
200) in the form of 3-digit event numbers.  One of
the following displays appears depending on the
editing status.
n###:Indicates that the No.### event is a new
event which has not been stored on the EDL
(edit list).  (New event)
d###:Indicates that the No.### event is an event
which has been deleted from the EDL.
###:Indicates that the No.### event has been
stored on the EDL.
FULL:Indicates that...

12
Panel switch area
1
CONTROL switch
REMOTE:For controlling the unit from the REMOTE
connector (9P).
LOCAL:For controlling the unit using the controls
on its front panel.
EXT VTR:For controlling an external VTR using the
controls on the unit’s front panel.  The
VTR connected to the 9P connector of
VTR1 can be controlled using the control
system of VTR1.
 
This switch is forcibly set to the LOCAL position in
the 625i mode.
2
PREROLL switch
Used to set the preroll time to 3, 5 or 7 seconds.
When the phase...

13
Panel switch area
7
ANALOG AUDIO IN switch
Used to set the allocation of the audio signals to the
4 analog audio input connectors (on the rear panel).
V1-V2 (2ch):Of the 4 inputs, the two on the VTR1
side are supplied to the VTR1’s input
connectors, and the two on the VTR2
side are supplied to the VTR2’s input
connectors.
V1 (4ch):The 4 inputs are allocated to the 4
channels of VTR1.
V2 (4ch):The 4 inputs are allocated to the 4
channels of VTR2.
8
ANALOG AUDIO OUT switch
Used to set the allocation of...

14
AUDIO control area
1
POWER switch
Used to control the unit’s power.
2
AUDIO MONITOR SELECT switches
Used to select the audio monitor output and
speaker output.
OV1/V1•2/V2 switch
V1:The VTR1 sound is output to the left and
right channels.
V1•2:The VTR1 sound is output to the left
channel and the VTR2 sound to the right
channel.
V2:The VTR2 sound is output to the left and
right channels.
OL (V1) switch, R (V2) switch
The selected audio channel sound is output to
the left (or right) channel.  When...

15
AUDIO control area
4
V1 audio playback level controls/V2 INT audio
recording level controls
These controls enable the playback audio level of
VTR1 to be adjusted for each channel.
They are also used to adjust the volume during
editing from VTR1 to VTR2.
Slide controls are used to make for fine and smooth
adjustments.
The position marked “0” denotes the reference
level.
(–20 dB for 525i mode; –18 dB for 625i mode)5
V2 AUDIO input selector switches
Used to select the sound which is to be input to the...

16
AUDIO control area
6
SDI audio recording level controls and UNI/VAR
switch
For each channel of the superimposed sound which
is input from the SDI input connector (on the rear
panel) there is one level control.
When the UNI/VAR switch is set to VAR, the audio
recording level can be adjusted separately for each
input channel.
When it is set to UNI, the levels are fixed to the
initial value regardless of the positions of the level
controls.
7
V2 audio playback level controls
These controls enable the...

17
Editing operation area
1
VTR1 selector button
Press this button to perform VTR1 editing-related
settings or operations.
Check that its LED has lighted before proceeding
with the VTR1 editing-related settings or
operations.
2
VTR2 selector button
Press this button to perform VTR2 editing-related
settings or operations.
Check that its LED has lighted before proceeding
with the VTR2 editing-related settings or
operations. 

The VTR1 and VTR2 simultaneous operation mode
is established by pressing ([SHIFT]...

18
Editing operation area
8
Search dial
This is used to control the tape travel.  It is also
used when edit points are to be located or when
playing back tapes.
The shuttle mode is established when the dial is
“out” (up), and the jog mode is established when it
is pushed in.
Each time the dial is pressed, the unit alternates
between these two modes.
9
ASMBL (1ST EDIT) button
ASMBL:
Press this button to initiate assemble editing.
Check that its LED has lighted before proceeding
with editing.
1ST EDIT...

19
Editing operation area
<
A2 (A4) button
A2:Press this button to initiate audio channel 2
insert editing.
Check that its LED has lighted before
proceeding with editing.
A4 ([SHIFT] + [A2]):
To initiate audio channel 4 insert editing, press
the A2 button while holding down the SHIFT
button.
Check that its LED has lighted before
proceeding with editing.

The A4 LED will light in the 25 Mbps mode also but
CH4 editing operations cannot be performed.
=
TC button
Press this button to initiate time code...

20
Editing operation area
?
EVENT button
EVENT:
To change the event number, press this button,
then use the numeric input keys to input the
event number, and press the ENTER button.
DELETE ([SHIFT] + [EVENT]):
Press this button to delete an event which has
been registered.
“d” is indicated in the event number display area.
@
IN (LAST X) button
IN:Press this button to set or display an edit IN
point.
LAST X ([SHIFT] + [IN]):
To re-register an event which has been deleted,
press this button while holding...