Panasonic Aj Lt95 Operating Instructions Manual

51
Operation methods
Analog component signals and analog composite
signals can be input and recorded using VTR1.
Recording with the 625i system is not possible.
1Set the OPERATION MODE mode switch (page
13) to SEPARATE.
2Select whether the signals are to be recorded in
the 50 Mbps mode or 25 Mbps mode using setup
menu item No.012 (SYS FORMAT).
3Check that “525” has been selected as the setup
menu item No.070 (TV SYSTEM) setting.

When the “525” or “625” setting has been changed,
turn off the power and...

52
Operation methods
Analog component signals, analog composite signals
and serial component digital signals can be played
back and output using VTR1 and VTR2.
Playback using VTR1, VTR2
1Set the OPERATION MODE mode switch (page
13) to SEPARATE.
2Select AUTO as the setup menu item No.013 (PB
FORMAT) setting.  If MANU has been selected,
select the setup menu item No.012 (SYS
FORMAT) setting which matches the format of the
tape to be played back.
3
4
When analog video signals are to be output, select...

53
Preparing tapes for editing
Before proceeding to commence editing, the black
burst signal, time code and CTL signal must first be
recorded on the tape.
The method of preparing the editing tape differs
depending on whether assemble editing or insert
editing is to be performed.
In the case of assemble editing, a run-up period must
be provided prior to the first assemble IN point.
The 1ST EDIT function is available as an easy way of
preparing the run-up period.
For the second and subsequent times, 1ST...

54
Preparing tapes for editing
Direction of tape travel
First assemble editing Present position where
IN point is registered
1ST EDIT TC setting 
1ST EDIT recording Title recording:
Approx. 7 sec.
Return 9 sec. 23 sec.
00:00:03:00 00:00:00:00 23:59:37:00
Characters and symbols can be superimposed onto
the video signals (black burst signals) and recorded
for about 7 seconds after the start of 1ST EDIT, but
this can be done only in the 525i mode.
Recording the editing titles, editing dates, equipment...

55
Preparing tapes for editing
In the case of insert editing, the black burst signal,
time code and CTL signal must be recorded for the
whole editing period in addition to the run-up period
for the assemble editing tape.
Method using normal recording Method using first edit (1ST EDIT)
Preparing tapes for insert editing
1Press the VTR2 button to select VTR2, and press
the PLAY button while holding down the REC
button.  VTR2 recording begins.
2If the preset value has been set in the TC preset
mode (R-RUN),...

56
Cut editing operations
Selecting the editing mode
1Press the ASMBL button.
In this mode, the video, audio (all channels) and
time code are recorded at the same time.

OTo clear the selected mode, press the same button
again to turn off the LED of the button concerned.
OSettings can also be performed for A3 and A4 in the
25 Mbps mode but the corresponding signals
cannot be edited in this mode.
Assemble editing:
2Check that the ASMBL button LED is lighted.
1Press all the buttons corresponding to the...

57
Cut editing operations
Storing the edit points
Select the VTR whose edit points are to be set
using the VTR1 button or VTR2 button. There are three main ways to store edit points.
2Use the search dial to search the edit point in the
shuttle mode or jog mode.
3Temporarily stop the tape at the edit point, and
press the MARK IN button or MARK OUT button.
This sets the edit IN point or OUT point.
1
1. Use the search dial to search the
editing screen, and set the edit point
using the MARK IN or MARK OUT...

58
Cut editing operations
Preview
Preview is a rehearsal of the editing before the editing
is performed for real.
When the PREVIEW button is pressed, the event
indicated by the event number display lamp is
previewed.The pictures and sound produced when editing is
actually performed will be played back as a simulation
on the VTR2 monitor, enabling them to be checked
out in advance.
What is played back is the length of tape from the
preroll point to the postroll point.
To repeat the preview from the start...

59
AUTO
EDIT
Cut editing operations
Executing editing
Press the AUTO EDIT button.
Review
Press the REVIEW ([SHIFT] + [PREVIEW]) button
right after executing editing. 
The executed editing is played back from the preroll
point to postroll point.
Preroll
pointEdit IN
pointEdit OUT
pointPostroll
point
ODuring assemble editing
ODuring insert editing Postroll time Preroll time
Postroll time
Postroll time Edit
recording
Edit recording Playback
Edit
recording
Review 
(rewind & play)  Review 
(rewind & play)...

60
Split editing operations
With insert editing, an audio IN point can be set
slightly ahead of the video IN point.  (Audio split
editing)Similarly, a video IN point can be set slightly ahead of
the audio IN point.  (Video split editing)
Slightly ahead of the video IN point.
(The audio IN point can also be placed
before the video IN point.) Audio split editing (video reference)
VTR1
IN
pointAudio IN
point
Video recording
Audio recordingOUT
point
VTR2Slightly ahead of the audio IN point.
(The video IN...