Oce PlotWave 300 User Manual

Make a copy with a stamp
Introduction
A stamp is a pre-defined text you can set on every copy.
Before you begin
If you must enter the same value for a setting very often, you can set this value as the de-
fault value for that setting in the Océ Express WebTools.
After you press the start key, the user panel always shows the job number and status of
the job. A copy job appears temporarily in the 'Jobs - Queue' section of the Océ Express
WebTools, a scan job appears in the Smart Inbox...

Scale to another media size
Introduction
You can use the 'Scale' setting to copy to a larger or smaller media format. Use one of the
following methods to scale a copy.
■Select another media format with the 'To fit' setting.
■Adjust a value in terms of percentage with the 'Custom' setting.
You can adjust a value between 10 and 1000%. A value lower than 100% reduces the
copy, a value greater than 100% enlarges the copy.
Before you begin
If you must enter the same value for a setting...

Result
The Océ PlotWave 300 copies to another media size.
Chapter 5 - Use the printing system
193
Scale to another media size
Downloaded From ManualsPrinter.com Manuals 

Make a copy on a cut sheet
Introduction
You can copy on cut sheet media if the required media type or size is not available on the
media rolls of the printer.
Before you begin
If you must enter the same value for a setting very often, you can set this value as the de-
fault value for that setting in the Océ Express WebTools.
After you press the start key, the user panel always shows the job number and status of
the job. A copy job appears temporarily in the 'Jobs - Queue' section of the Océ...

5.Wait for the media request.
6.Place the cut sheet media on the media bypass of the printer.
Note:
Use the media size indication on the media bypass to align the cut sheet media correctly.
If you use a B1 media size (707 mm) you must align the cut sheet media with the A1
indent.
Result
The Océ PlotWave 300 copies on a cut sheet.
Chapter 5 - Use the printing system
195
Make a copy on a cut sheet
Downloaded From ManualsPrinter.com Manuals   

Make a copy and add a strip
Introduction
You can use a strip to file a drawing.
Use 'Sheet size' to copy an original without a strip and add a strip to the copy. You can
add a strip at the top or bottom side of a copy.
Use 'Erase margins' to copy an original with a strip and remove the strip from the copy.
You can erase a margin from the top, the bottom, the left or the right side of the original.
Before you begin
If you must enter the same value for a setting very often, you can set this...

Result
The Océ PlotWave 300 adds a top or bottom strip to the copy.
Chapter 5 - Use the printing system
197
Make a copy and add a strip
Downloaded From ManualsPrinter.com Manuals 

Make a copy and erase a margin
Introduction
You can use a strip to file a drawing.
Use 'Sheet size' to copy an original without a strip and add a strip to the copy. You can
add a strip at the top or bottom side of a copy.
Use 'Erase margins' to copy an original with a strip and remove the strip from the copy.
You can erase a margin from the top, the bottom, the left or the right side of the original.
Before you begin
If you must enter the same value for a setting very often, you can set...

The 'Right' marginThe 'Left' marginThe 'Bottom' mar-
gin
The 'Top' margin
■Open a template with the confirmation button.
■Scroll to 'Erase margins' and open this setting with the confirmation button.
■Scroll to 'Top', 'Bottom', 'Left' or 'Right', define the value with the scroll wheel or
numeric keys and confirm.
4.Define the number of copies and press the green button.
Result
The Océ PlotWave 300 copies the original without a strip....

Make a copy of a specific area of an original
Introduction
You can make a copy of a specific area of an original with the 'Erase margins' setting.
Define the following strips to specify the area.
■'Top'
■'Bottom'
■'Left'
■'Right'
Before you begin
If you must enter the same value for a setting very often, you can set this value as the de-
fault value for that setting in the Océ Express WebTools.
After you press the start key, the user panel always shows the job...