Oce PlotWave 300 User Manual

Settings group: 'Resolution'
#
FunctionSettings valuesSetting
'The resolution of the scanned image in
dpi.'
'100'
'200'
'300'
'400'
'600'
'Resolution'
Settings group: 'Original'
#
FunctionSettings valuesSetting
Define the type of original you use'Line/text standard'
'Line/text draft'
'Colored original'
'Photo'
'Blueprint'
'Dark original'
'Folded line/text'
'Artwork'...

FunctionSettings valuesSetting
The width of the original is automatically
detected by the scanner.
'Auto''Width detect'
The width of the original is a standard
size.
Note:
Depend on the media series you
defined in the Océ Express
WebTools
'Standard'
Available standard sizes:
■'A0'
'A1'
'A2'
'A3'
'E+ (36")'
'B1 (707 mm)'
'B2 (19.69 in)'
The width of the original is a custom size.'Custom'
You can enter a size
within...

FunctionSettings valuesSetting
'Erase a strip from the bottom of the
original.'
0 to 400 mm'Bottom'
'Erase a strip from the left side of the
original.'
0 to 914 mm'Left'
'Erase a strip from the right side of the
original.'
0 to 914 mm'Right'
Settings group: 'Light and mirror'
#
FunctionSettings valuesSetting
Increase the value for lighter prints; de-
crease for darker prints.
-5 to +5'Lighter/dark-
er'
Chapter 5 - Use the printing system...

FunctionSettings valuesSetting
'When 'on', the image is mirrored along
the vertical axis (the media transport di-
rection).'
'On'
'Off'
'Mirror'
Settings group: 'Checkprint'
#
FunctionSettings valuesSetting
'When 'on', a print is made of the
scanned image. When scan-to-color is se-
lected, a check-print cannot be made. '
'On'
'Off'
'Checkprint'
Chapter 5 - Use the printing system
224
Available settings for scan jobs...

'File type'
Depending on the color mode and file type you select the values for the compression
mode and organization will change. For some File types, the Compression and Organiza-
tion settings cannot be set in all situations.
Color mode: Color
#
'JPEG quality''Compression''Organization''File type''Color' mode
Not applicable'LZW'
'Packbits'
'None'
'Raw'
'Stripped'
'Tiled'
'TIFF'
'TIFF multi-...

Color mode: Grayscale
#
'JPEG quality''Compression''Organization''File type''Color' mode
Not applicable'LZW'
'Packbits'
'None'
'Raw'
'Stripped'
'Tiled'
'TIFF'
'TIFF multi-
page'
'Grayscale'
Not applicable'Flate'
'None'
Not applicable'PDF'
'PDF/A'
'Maximum'
'High'
'Medium'
'Low'
'JPEG'
'Maximum'
'High'...

Make a scan and erase a margin
Introduction
Use 'Erase margins' to scan an original with a strip and remove the strip from the scanned
file. You can erase a margin from the top, the bottom, the left or the right side of the
original.
Before you begin
If you must enter the same value for a setting very often, you can set this value as the de-
fault value for that setting in the Océ Express WebTools.
After you press the start key, the user panel always shows the job number and status of
the job. A...

■Scroll to 'Top', 'Bottom', 'Left' or 'Right', define the value with the scroll wheel or
numeric keys and confirm.
5.Press the green button.
Result
The Océ PlotWave 300 scans the original without a strip.
Chapter 5 - Use the printing system
228
Make a scan and erase a margin
Downloaded From ManualsPrinter.com Manuals 

Chapter 6
Maintain the printing sys-
tem
Downloaded From ManualsPrinter.com Manuals 

Move the printing system
Switch off the printing system
1.Use the on / off button at the front side of the printer to switch off the printing system.
The lighted button starts to blink.
Note:
You can also use the 'Shut down' button in the Océ Express WebTools.
Attention:
Wait until the on / off button stops blinking.
Chapter 6 - Maintain the printing system
230
Switch off the printing system
Downloaded From ManualsPrinter.com Manuals