Oce PlotWave 300 User Manual

FunctionSettings valuesSetting
The width of the original is automatically
detected by the scanner.
'Auto''Width detect'
The width of the original is a standard
size.
Note:
Depend on the media series you
defined in the Océ Express
WebTools
'Standard'
Available standard sizes:
■'A0'
'A1'
'A2'
'A3'
'E+ (36")'
'B1 (707 mm)'
'B2 (19.69 in)'
The width of the original is a custom size.'Custom'
You can enter a size
within...

Settings group: 'Scale'
#
FunctionSettings valuesSetting
Scales the image to the original size.'1:1''1:1'
Scales the image to fit the selected media
size.
Note:
Depends on the media series you
defined in the Océ Express
WebTools
'A0'
'A1'
'A2'
'A3'
'E+ (36")'
'B1 (707 mm)'
'B2 (19.69 in)'
'To fit'
Scales the image to a custom percentage.10 - 1000'%''Custom'
Settings group: 'Delivery'
#...

FunctionSettings valuesSetting
The location to deposit the sheet face-up.'Back output'
Settings group: 'Sheet size'
#
FunctionSettings valuesSetting
'Determines the cut size of the print.
'Standard': the print is cut to a standard
media size (DIN, ANSI, ...). 'Synchro':
the print length depends on the image.'
'Synchro'
'Standard'
'Cut method'
'Adds a blank strip at the beginning of
the output.'
0 to 400 mm'Add leading
strip'...

Settings group: 'Positioning'
#
FunctionSettings valuesSetting
'Aligns the image on the media.''Top left'
'Top'
'Top right'
'Left'
'Center'
'Right'
'Bottom left'
'Bottom'
'Bottom right'
'Alignment'
'Shifts the image in the horizontal direc-
tion (after alignment to one of the posi-
tions given in 'Alignment').'
- 914 mm to + 914 mm'Shift horizon-
tal'
'Shifts the image in the...

FunctionSettings valuesSetting
'Erase a strip from the bottom of the
original.'
0 to 400 mm'Bottom'
'Erase a strip from the left side of the
original.'
0 to 914 mm'Left'
'Erase a strip from the right side of the
original.'
0 to 914 mm'Right'
Settings group: 'Erase area'
#
FunctionSettings valuesSetting
'The horizontal offset where the erase area
starts.'
0 to 914 mm'Hor offset'
Chapter 5 - Use the printing system
185
Available...

FunctionSettings valuesSetting
'The vertical offset where the erase area
starts.'
0 to 6000 mm'Vert offset'
'The width of the area to erase.'0 to 914 mm'Width'
'The length of the area to erase.'0 to 6000 mm'Length'
Settings group: 'Stamp'
#
FunctionSettings valuesSetting
Copy with a stampNone
------
'Stamp'
'The position of the stamp inside the leg-
end.'
'Top'
'Middle'
'Bottom'
'Position'
Chapter 5 -...

FunctionSettings valuesSetting
'The size of the stamp.''Small'
'Large'
'Size'
'The color of the stamp.''Light gray'
'Gray'
'Dark gray'
'Black'
'Color'
Settings group: 'Drawing method'
#
FunctionSettings valuesSetting
Defines which drawing method is used
for the legend position.
'DIN'
'Afnor'
'Ericsson'
'Method'
'Defines whether the legend is located at
the top (leading) or the...

Settings group: 'Light and mirror'
#
FunctionSettings valuesSetting
Increase the value for lighter prints; de-
crease for darker prints.
-5 to +5'Lighter/dark-
er'
'When 'on', the image is mirrored along
the vertical axis (the media transport di-
rection).'
'On'
'Off'
'Mirror'
Settings group: 'Sort'
#
FunctionSettings valuesSetting
If you want to copy multiple sheets, you
can indicate how the copied sheets must
be sorted.
'By page'...

Make multiple sets of copies
Introduction
You can use the 'Create set' option to make multiple sets of copies.
Before you begin
If you must enter the same value for a setting very often, you can set this value as the de-
fault value for that setting in the Océ Express WebTools.
After you press the start key, the user panel always shows the job number and status of
the job. A copy job appears temporarily in the 'Jobs - Queue' section of the Océ Express
WebTools, a scan job appears in the...

■Feed the next original, define the settings for this original if necessary and press the
green button.
You can use the lower right soft key to return to the default settings of your copy
template.
Repeat this step until all originals are fed.
4.Select 'Close set' with the lower left soft key.
How to make multiple sets of copies sorted by page
1.Feed the first original face up.
The scanner takes the original.
2.Open the 'Copy' tab with the confirmation button above the scroll wheel....