Oce PlotWave 300 User Manual

Note:
Depending on the selected 'Original release mode' in the Océ Express WebTools, the
scanner holds or releases the original after the scan procedure.
Chapter 5 - Use the printing system
211
Use the carrier sheet
Downloaded From ManualsPrinter.com Manuals 

Do a basic scan job
1.Feed the original face up and centered on the original feeding table.
Note:
You do not need to center the original precisely. The exact position of the original is au-
tomatically detected by the scanner.
2.Select 'Scan' on the user panel.
3.Press the green button.
Chapter 5 - Use the printing system
212
Do a basic scan job
Downloaded From ManualsPrinter.com Manuals   

Result
You do a basic scan job in 3 steps. The basic scan job uses the settings of the first scan
template.
Chapter 5 - Use the printing system
213
Do a basic scan job
Downloaded From ManualsPrinter.com Manuals 

Extended scan jobs
Introduction to scan jobs
A basic scan job only takes three steps. Feed the original face up, select 'Scan' on the user
panel and press the green button. Every other type of scan job is called an extended scan
job.
An extended scan job takes some additional steps, where you select a specific scan template
and, if necessary, change the predefined scan job settings on the user panel. The scan
templates are defined in the Océ Express WebTools (see ‘Define the scan job preferences...

RemarksCopy/Scan-to-file set-
ting'Original'
Original document
With scan-to-file for
'Photo' the color mode
'Grayscale'" is recommend-
ed.
With copy: 'Colored origi-
nal';
With Scan-to-file: 'Col-
ored original' or 'Photo'.
Medium quality prints
Only for very dark origi-
nals (mostly coming from
old archives).
'Dark original'Dark originals and dark
transparents
The image is inversed.'Blueprint'Blueprint
Chapter 5 - Use the printing...

Do an extended scan job
1.Feed the original face up and centered on the original feeding table.
Note:
You do not need to center the original precisely. The exact position of the original is au-
tomatically detected by the scanner.
2.Select 'Scan' on the user panel.
3.Open the 'Scan' tab with the confirmation button above the scroll wheel.
4.Select your scan template.
Chapter 5 - Use the printing system
216
Do an extended scan job
Downloaded From ManualsPrinter.com Manuals   

If you want to change the pre-defined settings of the selected scan template, use the
confirmation button to open the scan template and display an overview of the pre-defined
settings groups.
5.Scroll to the settings group you want to change.
6.■Open the settings group you want to change with the confirmation button and scroll
to the setting you want to change.
■Open this setting, scroll through the settings values and select the correct value with
the confirmation button.
■Change the other settings in...

■Select 'OK' to return to the overview of the predefined settings groups.
7.Repeat steps 5 and 6 until you have set all the correct values for your scan job.
8.Press the green button.
Chapter 5 - Use the printing system
218
Do an extended scan job
Downloaded From ManualsPrinter.com Manuals 

Available settings for scan jobs
Introduction
The Océ PlotWave 300 provides a lot of settings to manage all your different scan jobs.
These settings are used for extended scan jobs. The following table gives an overview and
a very short description of the available settings. You can find a detailed description of
each setting in the Océ Express WebTools.
Settings group: 'Destination'
#
FunctionSettings valuesSetting
'The destination to put the scans into.'
(see ‘Configure a local scan...

FunctionSettings valuesSetting
'Defines whether a color, grayscale or
black-and-white scan must be made. Not
all combinations of 'Color mode' and
'File type' are valid. Changing 'Color
mode' resets 'File type', 'Compression for
TIFF' and 'Compression for PDF' to a
default value.'
'Color'
'Grayscale'
'Black&white'
'Color'
'The file type of the scanned image. The
list of file types depends on scan to color,...