Home > Oce > Printer > Oce PlotWave 300 User Manual

Oce PlotWave 300 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Oce PlotWave 300 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 5 Oce manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Make a copy with a stamp
    Introduction
    A stamp is a pre-defined text you can set on every copy.
    Before you begin
    If you must enter the same value for a setting very often, you can set this value as the de-
    fault value for that setting in the Océ Express WebTools.
    After you press the start key, the user panel always shows the job number and status of
    the job. A copy job appears temporarily in the 'Jobs - Queue' section of the Océ Express
    WebTools, a scan job appears in the Smart Inbox 'Scans'.
    How to make a copy with a stamp
    1.Feed the original face up and centered on the original feeding table.
    Note:
    You do not need to center the original precisely. The exact position of the original is au-
    tomatically detected by the scanner.
    The 'Copy' tab is automatically activated on the user panel.
    2.Open the 'Copy' tab with the confirmation button above the scroll wheel.
    3.Define the job settings.
    ■Open a template with the confirmation button.
    ■Scroll to 'Stamp' and open this setting with the confirmation button.
    ■Scroll to 'Stamp', select a stamp with the scroll wheel and confirm.
    ■Scroll to 'Position', select the correct position with the scroll wheel and confirm.
    ■Scroll to 'Size', select the correct size with the scroll wheel and confirm.
    ■Scroll to 'Color', select the correct color with the scroll wheel and confirm.
    4.Define the number of copies and press the green button.
    Result
    The copy contains the selected stamp.
    Chapter 5 - Use the printing system
    191
    Make a copy with a stamp
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Scale to another media size
    Introduction
    You can use the 'Scale' setting to copy to a larger or smaller media format. Use one of the
    following methods to scale a copy.
    ■Select another media format with the 'To fit' setting.
    ■Adjust a value in terms of percentage with the 'Custom' setting.
    You can adjust a value between 10 and 1000%. A value lower than 100% reduces the
    copy, a value greater than 100% enlarges the copy.
    Before you begin
    If you must enter the same value for a setting very often, you can set this value as the de-
    fault value for that setting in the Océ Express WebTools.
    After you press the start key, the user panel always shows the job number and status of
    the job. A copy job appears temporarily in the 'Jobs - Queue' section of the Océ Express
    WebTools, a scan job appears in the Smart Inbox 'Scans'.
    How to copy to another media size
    1.Feed the original face up and centered on the original feeding table.
    Note:
    You do not need to center the original precisely. The exact position of the original is au-
    tomatically detected by the scanner.
    The 'Copy' tab is automatically activated on the user panel.
    2.Open the 'Copy' tab with the confirmation button above the scroll wheel.
    3.Define the job settings.
    ■Open a template with the confirmation button.
    ■Scroll to 'Scale' and open this setting with the confirmation button.
    ■Scroll to 'To fit', select a standard media format from the media series you use and
    confirm.
    4.Define the number of copies and press the green button.
    Chapter 5 - Use the printing system
    192
    Scale to another media size
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Result
    The Océ PlotWave 300 copies to another media size.
    Chapter 5 - Use the printing system
    193
    Scale to another media size
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Make a copy on a cut sheet
    Introduction
    You can copy on cut sheet media if the required media type or size is not available on the
    media rolls of the printer.
    Before you begin
    If you must enter the same value for a setting very often, you can set this value as the de-
    fault value for that setting in the Océ Express WebTools.
    After you press the start key, the user panel always shows the job number and status of
    the job. A copy job appears temporarily in the 'Jobs - Queue' section of the Océ Express
    WebTools, a scan job appears in the Smart Inbox 'Scans'.
    How to copy on a cut sheet
    1.Feed the original face up and centered on the original feeding table.
    Note:
    The page orientation must be portrait.
    Note:
    You do not need to center the original precisely. The exact position of the original is au-
    tomatically detected by the scanner.
    The 'Copy' tab is automatically activated on the user panel.
    2.Open the 'Copy' tab with the confirmation button above the scroll wheel.
    3.Define the job settings.
    ■Open a template with the confirmation button.
    ■Scroll to 'Media' and open this setting with the confirmation button.
    ■Scroll to 'Feed', select 'Manual' with the scroll wheel and confirm.
    The settings 'Size' and 'Type' appear.
    ■Scroll to 'Size', select the correct media size with the scroll wheel and confirm.
    ■Scroll to 'Type', select the correct media type with the scroll wheel and confirm.
    4.Define the number of copies and press the green button.
    Chapter 5 - Use the printing system
    194
    Make a copy on a cut sheet
    Downloaded From ManualsPrinter.com Manuals 
    						
    							5.Wait for the media request.
    6.Place the cut sheet media on the media bypass of the printer.
    Note:
    Use the media size indication on the media bypass to align the cut sheet media correctly.
    If you use a B1 media size (707 mm) you must align the cut sheet media with the A1
    indent.
    Result
    The Océ PlotWave 300 copies on a cut sheet.
    Chapter 5 - Use the printing system
    195
    Make a copy on a cut sheet
    Downloaded From ManualsPrinter.com Manuals   
    						
    							Make a copy and add a strip
    Introduction
    You can use a strip to file a drawing.
    Use 'Sheet size' to copy an original without a strip and add a strip to the copy. You can
    add a strip at the top or bottom side of a copy.
    Use 'Erase margins' to copy an original with a strip and remove the strip from the copy.
    You can erase a margin from the top, the bottom, the left or the right side of the original.
    Before you begin
    If you must enter the same value for a setting very often, you can set this value as the de-
    fault value for that setting in the Océ Express WebTools.
    After you press the start key, the user panel always shows the job number and status of
    the job. A copy job appears temporarily in the 'Jobs - Queue' section of the Océ Express
    WebTools, a scan job appears in the Smart Inbox 'Scans'.
    How to make a copy and add a strip
    1.Feed the original face up and centered on the original feeding table.
    Note:
    You do not need to center the original precisely. The exact position of the original is au-
    tomatically detected by the scanner.
    The 'Copy' tab is automatically activated on the user panel.
    2.Open the 'Copy' tab with the confirmation button above the scroll wheel.
    3.Define the job settings.#
    'Add trailing strip''Add leading strip'
    ■Open a template with the confirmation button.
    ■Scroll to 'Sheet size' and open this setting with the confirmation button.
    ■Scroll to 'Add leading strip' or 'Add trailing strip', define the value with the scroll
    wheel or numeric keys and confirm.
    4.Define the number of copies and press the green button.
    Chapter 5 - Use the printing system
    196
    Make a copy and add a strip
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Result
    The Océ PlotWave 300 adds a top or bottom strip to the copy.
    Chapter 5 - Use the printing system
    197
    Make a copy and add a strip
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Make a copy and erase a margin
    Introduction
    You can use a strip to file a drawing.
    Use 'Sheet size' to copy an original without a strip and add a strip to the copy. You can
    add a strip at the top or bottom side of a copy.
    Use 'Erase margins' to copy an original with a strip and remove the strip from the copy.
    You can erase a margin from the top, the bottom, the left or the right side of the original.
    Before you begin
    If you must enter the same value for a setting very often, you can set this value as the de-
    fault value for that setting in the Océ Express WebTools.
    After you press the start key, the user panel always shows the job number and status of
    the job. A copy job appears temporarily in the 'Jobs - Queue' section of the Océ Express
    WebTools, a scan job appears in the Smart Inbox 'Scans'.
    Attention:
    When you erase a margin, make sure that you copied all the required information.
    How to make a copy and remove a margin
    1.Feed the original face up and centered on the original feeding table.
    Note:
    You do not need to center the original precisely. The exact position of the original is au-
    tomatically detected by the scanner.
    The 'Copy' tab is automatically activated on the user panel.
    2.Open the 'Copy' tab with the confirmation button above the scroll wheel.
    3.Define the job settings.#
    Chapter 5 - Use the printing system
    198
    Make a copy and erase a margin
    Downloaded From ManualsPrinter.com Manuals 
    						
    							The 'Right' marginThe 'Left' marginThe 'Bottom' mar-
    gin
    The 'Top' margin
    ■Open a template with the confirmation button.
    ■Scroll to 'Erase margins' and open this setting with the confirmation button.
    ■Scroll to 'Top', 'Bottom', 'Left' or 'Right', define the value with the scroll wheel or
    numeric keys and confirm.
    4.Define the number of copies and press the green button.
    Result
    The Océ PlotWave 300 copies the original without a strip. You can also use this setting
    to copy a specific area of the original. (see ‘Make a copy of a specific area of an original’ on
    page 200).
    Chapter 5 - Use the printing system
    199
    Make a copy and erase a margin
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Make a copy of a specific area of an original
    Introduction
    You can make a copy of a specific area of an original with the 'Erase margins' setting.
    Define the following strips to specify the area.
    ■'Top'
    ■'Bottom'
    ■'Left'
    ■'Right'
    Before you begin
    If you must enter the same value for a setting very often, you can set this value as the de-
    fault value for that setting in the Océ Express WebTools.
    After you press the start key, the user panel always shows the job number and status of
    the job. A copy job appears temporarily in the 'Jobs - Queue' section of the Océ Express
    WebTools, a scan job appears in the Smart Inbox 'Scans'.
    Attention:
    When you erase a margin, make sure that you copied all the required information.
    How to copy a specific area of an original
    1.Feed the original face up and centered on the original feeding table.
    Note:
    You do not need to center the original precisely. The exact position of the original is au-
    tomatically detected by the scanner.
    The 'Copy' tab is automatically activated on the user panel.
    2.Open the 'Copy' tab with the confirmation button above the scroll wheel.
    3.Define the job settings.#
    Chapter 5 - Use the printing system
    200
    Make a copy of a specific area of an original
    Downloaded From ManualsPrinter.com Manuals 
    						
    All Oce manuals Comments (0)