Nortel Compact Ics 6.1 System Coordinator Guide

Using the Hospitality features / 191
P0603544   02 Compact ICS 6.1 Syste m Coordin ator Guide
Using the Administration set to control alarms
Only a Hospitality Services set can use this alarm administration feature. 
This feature is also associated with a room number, and cannot be used on 
common sets.
Use this feature to:
query a current or last alarm time set for a room
assign an alarm time for any room
change an alarm time for any room
cancel an pending alarm for any room
To program the alarm,...

192 / Using the Hospitality features
Com pact ICS 6.1 System Coordinator Guide P0603544   02
Using the alarm
To set an alarm on a digital telephone:
1. Press 
²¡àÞ.The displays shows Alrm:07:00 OFF
2. Do one of the following:
If the alarm is correct, press 
ON/OFF.The set displays: Alrm:07:00am 
ON
. Press DONE to exit.
If you need to change the alarm time, press 
CHG. The set displays: 
Enter time: 
3. To enter a new time, do one of the following:
If the clock uses a 24-hour format, enter an hour...

Using the Hospitality features / 193
P0603544   02 Compact ICS 6.1 Syste m Coordin ator Guide
Turning off an alarm
When the alarm rings, the user can release the ring by doing one of the 
following, depending on the type of telephone in the room:
Digital set: Press any button except 
³.
Analog set: Lift and replace the handset.
³acts like a snooze alarm and will temporarily disable the alarm for a 
programmed period. Refer to ‘‘Service times’’ on page 187.
If the user is on a call when the alarm sounds,...

194 / Using the Hospitality features
Com pact ICS 6.1 System Coordinator Guide P0603544   02 

P0603544   02 Compact ICS 6.1 Syste m Coordin ator Guide
Telephone features
Installing Business Series Terminals
If you are connecting a Business Series Terminal (BST) for the first time, 
refer to the following illustrations as a guide.
Installing the Business Series Terminal connections
Installing to a desk jack 

196 / Telephone features
Com pact ICS 6.1 System Coordinator Guide P0603544   02
Mounting a Business Series Terminal on the wall
Mounting a Business Series Terminal on the wall
Installing without the angled base 

Telephone features / 197
P0603544   02 Compact ICS 6.1 Syste m Coordin ator Guide
Mounting a Business Series Terminal using the stand
Mount the telephone 
    onto the screws and 
slide it down. Mount the stand as shown and
insert screw. Use the screw that
came with your keystation.
  Use the key hole slots on the stand
to mark the location for the screws.
key hole slots
Connect line cord to 
wall jack.  Connect cords to the  telephone,
    refer to cord connections
  Tighten screws for a secure fit. 

198 / Telephone features
Com pact ICS 6.1 System Coordinator Guide P0603544   02
Installing Norstar telephones
If you are connecting a Norstar telephone for the first time, refer to the 
illustrations below and use as a guideline.
Installing a Norstar telephone
Connect to 
jack wired from
distribution block
Connect to 
receiverConnect to jack 
wired from 
distribution block
Connect to 
receiver 

Telephone features / 199
P0603544   02 Compact ICS 6.1 Syste m Coordin ator Guide
Mounting a Norstar telephone on the wall
12
34
56 

200 / Telephone features
Com pact ICS 6.1 System Coordinator Guide P0603544   02
Naming a telephone or a line
You can assign names to identify external lines, target lines, and telephones 
assigned to specific people. During a call, the name (if programmed) is 
shown on the telephone display instead of the external line number or 
internal telephone number of the caller. Step-by-step instructions for 
adding or changing the name of a telephone or a line are in ‘‘Changing the 
name of a telephone’’ on...