Nitsuko Ds2000 Software Manual

Flash
DS2000 Software ManualChapter 1: Features133
Toll Restriction (page 314)
The system enforces normal Toll Restriction after the Flash.
Feature Operation
To Flash the trunk you are on:
1. Press FLASH
2. Dial the code for the desired CO/PBX feature.A brief interruption, followed by new CO/PBX dial tone.
Line/loop key on (green). 

Flexible Numbering Plan
134Chapter 1: FeaturesDS2000 Software Manual
Flexible Numbering Plan
Description
The system’s Flexible Numbering Plan allows you to change the digits users dial to reach the atten-
dant, other co-worker’s and trunks. The following chart shows the areas of the system number plan 
you can change.
Conditions
None
Default Setting
See the table above.
Programming Guide
LCCPU 01.00.00 Available.
Change the digits users dial for co-workers and other features.
For this feature:You can...

Flexible Numbering Plan
DS2000 Software ManualChapter 1: Features135
Programming List
Program 0501 - Numbering Plan (page 392)
Customize the system’s number plan by changing the digits users dial to reach an operator, 
co-workers (i.e., Intercom), Direct Trunk Access and Trunk Group Access.
Program 0504 - Trunk Port Extension Numbers (page 396)
Enter the extension number associated with each trunk port.
Program 0505 - Station Port Extension Numbers (page 398)
Enter the extension number associated with...

Flexible Numbering Plan
136Chapter 1: FeaturesDS2000 Software Manual
Other Related Features
Attendant Position (page 24)
Change the digits users dial to reach the system operators (normally 0 or 01-04).
Central Office Calls, Placing (page 63)
Change the digits users dial to access a Trunk Group for an outside call (normally 90-98).
Direct Trunk Access (page 106)
Change the digits users dial to directly access a trunk (normally 401-416).
Extension Hunting (page 121)
UCD Hunting group master numbers can be...

Forced Trunk Disconnect
DS2000 Software ManualChapter 1: Features137
Forced Trunk  Disconnect
Description
Forced Trunk Disconnect allows an extension user to disconnect (release) another extension’s 
active trunk call. Forced Trunk Disconnect lets a user access a busy trunk in an emergency, when no 
other trunks are available. Maintenance technicians can also use Forced Trunk Disconnect to 
release a trunk on which there is no conversation. This can happen if a trunk does not properly dis-
connect when...

Forced Trunk Disconnect
138Chapter 1: FeaturesDS2000 Software Manual
Programming List
Program 0101 - Forced Trunk Disconnect (page 363)
In an extension’s Class of Service, enter Y to enable the ability to use Forced Trunk Discon-
nect.
Program 1801 - Extension Class of Service Assignment (page 450)
Assign Class of Service to extensions.
Program 1803 - Extension Line Access Assignments (page 461)
An extension can only use Forced Trunk Disconnect on a trunk to which it has outgoing 
(option 2) or full...

Group Call Pickup
DS2000 Software ManualChapter 1: Features139
Group Call Pickup
Description
Group Call Pickup allows an extension user answer a call ringing an extension in their assigned 
Pickup Group.This permits co-workers in the same Pickup Group to easily answer each other’s 
ringing calls. The user can intercept the ringing call by dialing a code or pressing a programmed 
Group Call Pickup key. The system has a maximum of eight Pickup Groups, with an unlimited 
number of extensions in each group....

Group Call Pickup
140Chapter 1: FeaturesDS2000 Software Manual
Step 2: Should an incoming call on a trunk ring all extensions in a Pickup Group?
• In Program 1003 - Call Pickup Group (page  426), 
assign the trunk to a Pickup Group (1-8).
• In Program 1803 - Extension Line Access Assign-
ments (page 461), make sure extensions in the 
Pickup Group have incoming (option 1) or full 
(option 3) access to the trunk.
• In Program 1805 - Ring Assignments (page 466), 
make sure to enable ringing for all...

Group Call Pickup
DS2000 Software ManualChapter 1: Features141
Programming List
Program 1003 - Call Pickup Group (page 426)
Have an incoming call on the trunk ring all the extensions in the assigned pickup group.
Program 1701 - Programmable Function Key Assignments (page 436)
Assign a programmable key on an extension as a Group Call Pickup key (09 = Immediate 
Ring, 10 = No Ring, 11 = Delayed Ring). The options are 1-8 (Pickup Groups 1-8) or 0 (unas-
signed).
Program 1704 - DSS Console Key Assignment...

Group Listen
142Chapter 1: FeaturesDS2000 Software Manual
Group Listen
Description
Group Listen permits a keyset user to talk on the handset and have their caller’s voice broadcast 
over the telephone speaker. This lets the keyset user’s co-workers listen to the conversation. Group 
Listen turns off the keyset’s Handsfree microphone so the caller does not hear the co-worker’s 
voices during a Group Listen.
Conditions
None
Default Setting
Enabled
Programming List
Programming List
Program 1807 - Headset...