Nitsuko 124i/384i Software Manual

0015 - Automatic Backup
  Sorts Data   Updates CEU   Can be Copied
Description
 124i Not applicable. 384i Available — requires system
software 3.06.02 or higher.
INUse Program 0015 - Automatic Backup to automatically back up program data to the CPRU floppy disk. This
helps ensure that the system will retain site-specific data in the event of a power failure or system reset. You can
set the Automatic Backup to occur:
•On a specific day of the month at a preset time.
 OR
•On selected day(s) of the week...

0091 - View System Report
  Sorts Data   Updates CEU   Can be Copied
Description
 124i Available from PC program only. 384i Available from PC program only.
INUse Program 0091 - View System Report to display an abbreviated system report. To have the entire system re-
port output on the report printer, refer to 0007 - System Report Port Setup. To upload the system report from
the system to the PC program, use PC program option Main Menu -> Communication -> O/M Command -
> 03 Read System Information.
384i...

0092 - View Alarm Report
  Sorts Data   Updates CEU   Can be Copied
Description
 124i Available from PC program only. 384i Available from PC program only.
IN
Use Program 0092 - View Alarm Report to display the alarm report. To have the alarm report output on
the report printer, refer to 0008 - Alarm Report Port Setup. To upload the alarm report from the system to
the PC program, use PC program option Main Menu -> Communication -> O/M Command -> 04 Read
Alarm Report.
Conditions
None
Feature Cross...

— For Your Notes —
0000 - Maintenance Options
0092 - View Alarm Report
648   PROGRAMMING 92000SWG08  Issue 1-0 

0100 - Basic Hardware Setup (Part A)0101 - DTMF Tone Duty Cycle
 Sorts Data
✔  Updates CEU   Can be Copied
Description
 124i Available. 384i Available.
INUse Program 0101 - DTMF Tone Duty Cycle to set the DTMF tone duration (on time) and pause (off time) for
all trunk calls. This option affects all trunk calls system wide. You make separate entries for duration and pause.
Each entry is in 10 mS increments (e.g., entry 10 = 100 mS). The range is 1 (10 mS) to 255 (2.55 seconds).
Conditions
None
Feature...

0103 - Time and Date Display Mode
  Sorts Data   Updates CEU   Can be Copied
Description
 124i Available. 384i Available.
INUse Program 0103 - Time and Date Display to set how the Time and Date appear on display telephones. There
are eight display modes (see the following chart):
Time and Date Display Modes
Mode Type Sample
1 12 hour 10 MAR TUE 3:15PM
2 12 hour 3:15PM MAR 10 TUE
3 12 hour 3-10 TUE 3:15 PM
4 12 hour 3:15PM TUE 10 MAR
5 24 hour 10 MAR TUE 15:15
6 24 hour 15:15 MAR 10 TUE
7 24 hour 3-10...

0104 - DP to DTMF Conversion Options
 Sorts Data  Updates CEU
✔  Can be Copied
Description
 124i Available. System has 52 trunk ports
(1-52). 384i Available. System has 128 trunk
ports (1-128).
INUse Program 0104 - DP to DTMF Conversion Options to determine how a user can convert a Dial Pulse (DP)
call to a DTMF call. for each trunk, set the type of DP to DTMF conversion required. There are three conversion
options:
•0 - Automatic
DP to DTMF conversion occurs automatically if the extension user waits...

0109 - Keyset Splash Tone
✔  Sorts Data   Updates CEU   Can be Copied
Description
 124i Available. 384i Available. After you change this
program and exit programming, the
system will reset for about thirty
seconds. 
- Requires Base 2.13, EXCPRU 2.18
or higher.- Requires system software 3.04 or
higher.
INUse this program to set the frequency of the system’s splash tone. This is the tone the system uses, for example,
to alert the user of an incoming voice-announced Intercom call. When changing a tone,...

Feature Cross Reference
Distinctive Ringing, Tones and Flash Patterns
Telephone Programming Instructions
To enter data for Program 0109 (Keyset Splash Tone):
1. Enter the programming mode.
2. 0109 + HOLD
FREQ:nn-
The previously programmed value displays.
3. Enter the number of the new splash tone.
Refer to the table on the previous page for splash tone numbers.
4. HOLD to exit.
When you exit the programming mode, the system will restart (about 6 seconds in 124i - about
30 seconds in 384i).
0100 - Basic...

0110 - Keyset Confirmation Tone
✔  Sorts Data   Updates CEU   Can be Copied
Description
 124i Available. 384i Available. After you change this
program and exit programming, the
system will reset for about thirty
seconds. 
Requires Base 2.13, EXCPRU 2.18
or higher.Requires system software 3.04 or
higher.
INUse this program to set the frequency and duration of the Dial Pad Confirmation Tone. When an extension user
enables Dial Pad Confirmation Tone (Service Code 824), they hear this tone each time they...