NEC Xen Ipk Features And Specifications Manual

Features and Specifications Manual A16 – 61
Doc. No. 8201 - Release 1.0
July 2003
Authorisation CodeA-16
FEATURE 
DESCRIPTIONAuthorisation Code permits a station to dial outside numbers that would
otherwise be restricted. When an access code plus Authorisation Code is
dialled, the station code restriction class temporarily changes to allow calls
when permitted by a new code restriction class.
The Authorisation Code can be verified or unverified based on class of
service and is assigned in the...

July 2003 NEC Business Solutions Ltd
62  – A16Authorisation Code
Doc. No. 8201 - Release 1.0
July 2003
5. Press N to enter the information. The next Account Number
is displayed. Repeat steps 4~5 until all desired Account Codes
are entered.
6. Press 
P to stop entering Forced Account Codes/Authorisation
Codes.
SERVICE 
CONDITIONS	Verified or Unverified for the Forced Account Code/Authorisation Code
features.
	Memory Block 1-8-08 (Class of Service (Station) Feature Selection 2),
Page 6, LK 3 is used to...

Xen IPK Features and Specifications Manual
Features and Specifications Manual A16 – 63
Doc. No. 8201 - Release 1.0
July 2003
	Existing restrictions (permitted by the temporary change to code
restriction class) and Least Cost Routing (LCR) assignments are
applied after Forced Account Codes/Authorisation Codes are entered.
	Verified and Unverified Forced Account Code/Authorisation Code
cannot be used in the same Class of Service.
RELATED 
FEATURES LIST
GUIDE TO 
FEATURE 
PROGRAMMINGFeature 
NumberFeature...

July 2003 NEC Business Solutions Ltd
64  – A16Authorisation Code
Doc. No. 8201 - Release 1.0
July 2003
¶+ASPrinter Connected Selection 1-5-13
¶+AS Printer Line Feed Control Selection 1-5-14
¶+ASSMDR Incoming/Outgoing Print Selection 1-5-26
¶+ASSMDR Valid Call Time Assignment 1-5-25
¶+ASSMDR Print Format 1-5-02
¶+ASSMDR Telephone Print Selection 4-56
¶+CSSCOM Port Baud Rate Setting Assignment 1-8-35
¶+BMStart Time Selection 1-1-05
4When the system is at default this Memory Block must be programmed for the...

Features and Specifications Manual A17 – 65
Doc. No. 8201 - Release 1.0
July 2003
Automatic Answer with 
Delay Message
A-17
FEATURE 
DESCRIPTIONThe Automatic Answer with Delay Message feature answers incoming CO/
PBX calls and plays a specified message to the outside caller while still
ringing designated stations. Up to two messages can be played to the
outside caller. The message(s) played are the same as the Automated
Attendant message(s).
SYSTEM 
AVAILABILITYTerminal Type
Not applicable.
Required...

July 2003 NEC Business Solutions Ltd
66  – A17 Automatic Answer with Delay Message
Doc. No. 8201 - Release 1.0
July 2003
1. Press T.
2. Dial 
HA.
3. Dial the incoming trunk number (
00~FD). [00 = All CO/
PBX lines].
Note:Dialling 00 sets or cancels the Automated Attendant mode for all
trunks when the trunks are idle. If a trunk is busy when 00 is dialled, it
is not set. To set the Automated Attendant to a busy trunk, dial the
individual trunk number.
4. Press T.
1. Press
T.
2. Dial 
HB.
3. Dial the...

Xen IPK Features and Specifications Manual
Features and Specifications Manual A17 – 67
Doc. No. 8201 - Release 1.0
July 2003
1. Receive an incoming CO/PBX call.
2. The Automatic Answer with Delay Message answers the call and
sends a greeting.
3. The outside party hears ringback tone or MOH (System
Programmable).
4. After the time expires, a second message is played.
5. The outside party hears ringback tone or MOH until the call is
answered.
SERVICE 
CONDITIONSData Assignment
	A maximum of eight VRS(4)-U(...

July 2003 NEC Business Solutions Ltd
68  – A17 Automatic Answer with Delay Message
Doc. No. 8201 - Release 1.0
July 2003
General
	The Automatic Answer with Delay Message features uses the
Automated Attendant Message to play to the outside caller.
	DIT/ANA assigned to the same trunk has higher priority.
	Automated Attendant and system Access Codes can be assigned
individually.
	Automated Attendant assignment is assigned to tenants and follows
the tenants Day/Night/Weekend mode switching.
	If Automated...

Xen IPK Features and Specifications Manual
Features and Specifications Manual A17 – 69
Doc. No. 8201 - Release 1.0
July 2003
¶+AU4Automated Attendant Delay Announcement 
Assignment1-4-18
¶+AU  4Automated Attendant 1st to 2nd Delay 
Announcement Interval Time1-4-19
¶+AU 4Automated Attendant Delay Announcement 
Disconnect Time1-4-20
¶+BCT4Trunk Incoming Answer Mode Selection3-05
¶+AUAutomated Attendant Message to Trunk Selection 3-38
¶+AU4Automated Attendant Function Selection3-59
¶+BA4Access Code (1-, 2-,...

July 2003 NEC Business Solutions Ltd
70  – A17 Automatic Answer with Delay Message
Doc. No. 8201 - Release 1.0
July 2003
THIS PAGE INTENTIONALLY LEFT BLANK