NEC Xen Ipk Features And Specifications Manual

Features and Specifications Manual A24 – 101
Doc. No. 8201 - Release 1.0
July 2003
Automatic HoldA-24
FEATURE 
DESCRIPTIONThe Automatic Hold feature works when an Attendant with an Attendant
Add-On Console presses a DSS key programmed for station or page
access while engaged in an outside call or when Multiline Terminal users,
engaged in an outside call, press a Feature Access key or One-Touch key
programmed for Direct Station Selection or Direct Paging Access. This
feature reduces the risk of...

July 2003 NEC Business Solutions Ltd
102  – A24Automatic Hold
Doc. No. 8201 - Release 1.0
July 2003
GUIDE TO 
FEATURE 
PROGRAMMING
THIS PAGE INTENTIONALLY LEFT BLANK
Order
and
Shortcut
System Data NameMemory 
BlockFunction
1-8-07
Attendant
Page-Line 
Key1-8-08
Station
Page-Line 
Key
¶+BTDAttendant Add-On Console to Telephone Port 
Assignment1-6-01
¶+BTDAttendant Add-On Console Key Selection 1-6-05
¶+BTMLine Key Selection for Telephone Mode 4-12
¶+BTMExtension Line Key Ring Assignment (Day Mode) 4-37...

Features and Specifications Manual A25 – 103
Doc. No. 8201 - Release 1.0
July 2003
Automatic RedialA-25
FEATURE 
DESCRIPTIONThe Automatic Redial feature simplifies repetitive Dialling to a busy or
unanswered outgoing call. When receiving a busy tone or no answer while
attempting to make a CO/PBX call, the system periodically redials the party
number while the station user monitors the call for completion.
SYSTEM 
AVAILABILITYTerminal Type
All terminals.
Required Components
None.
OPERATING 
PROCEDURES
1....

July 2003 NEC Business Solutions Ltd
104  – A25Automatic Redial
Doc. No. 8201 - Release 1.0
July 2003
SERVICE 
CONDITIONSData Assignment
	Automatic Redial timeout options are programmable as follows: 
Restrictions
	The station retains sole use of the outside line during Automatic
Redial.
	If an internal call is received during Automatic Redial, it cannot be
answered unless Automatic Redial is released. The calling station
receives a call waiting tone.
	This feature is not available for Single Line...

Xen IPK Features and Specifications Manual
Features and Specifications Manual A25 – 105
Doc. No. 8201 - Release 1.0
July 2003
GUIDE TO 
FEATURE 
PROGRAMMING
Order
and
Shortcut
System Data NameMemory 
BlockFunction
1-8-07
Attendant
Page-Line 
Key1-8-08
Station
Page-Line 
Key
¶+BMAutomatic Redial Time Selection 1-1-04
¶+BTSManual Pause Selection 1-1-09 

July 2003 NEC Business Solutions Ltd
106  – A25Automatic Redial
Doc. No. 8201 - Release 1.0
July 2003
THIS PAGE INTENTIONALLY LEFT BLANK 

Features and Specifications Manual A26 – 107
Doc. No. 8201 - Release 1.0
July 2003
Automatic ReleaseA-26
FEATURE 
DESCRIPTIONThe Automatic Release feature releases the outside line circuit when an
outside party has abandoned the call. For this feature to work with Loop
Start Trunks, the CO/PBX providing the outside line must provide a line
reversal signal or busy tone upon disconnect. Automatic release is also
normally provided on DID, ISDN, and Tie Line Trunks.
SYSTEM 
AVAILABILITYTerminal Type
Not...

July 2003 NEC Business Solutions Ltd
108  – A26Automatic Release
Doc. No. 8201 - Release 1.0
July 2003
THIS PAGE INTENTIONALLY LEFT BLANK 

Features and Specifications Manual A27 – 109
Doc. No. 8201 - Release 1.0
July 2003
Automatic Trunk-to-Trunk
Transfer
A-27
FEATURE 
DESCRIPTIONThis feature allows an incoming CO/PBX call to connect to another CO/PBX
trunk and dial a predetermined telephone number. This is especially useful
for forwarding calls to an answering service during non business hours (i.e.,
nights, weekends, holidays).
SYSTEM 
AVAILABILITYTerminal Type:
Attendant Position terminals assigned for this ability.
Required Components:...

July 2003 NEC Business Solutions Ltd
110  – A27 Automatic Trunk-to-Trunk Transfer
Doc. No. 8201 - Release 1.0
July 2003
1. PressT.
2. Dial 
FA.
3. Dial the incoming trunk number (
0A~FD,00)
4. Press
T.
Note:Dialling 00 sets or cancels the Automated Attendant mode for all
trunks when the trunks are idle. If a trunk is busy when 00 is dialled, it
is not set. To set the Automated Attendant to a busy trunk, dial the
individual trunk number.
1. Press T.
2. Dial 
FB.
3. Dial the incoming trunk number (...