NEC Neax2000 Ivs Isdn System Manual

ND-45857 (E) CHAPTER 4
Page 71
Revision 3.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Assign ISDN Local Office Code Table Number 
to each ISDN trunk.
Assign trunk route data to the route number 
assigned by CM30 YY=00.
Note 1:This data should be assigned to the B
channel trunk route. This data should
be assigned to both B channel trunk
route and D channel trunk route.
Specify the number of digits to be received on
DID.
Note:If CM35 YYY=143 is set to “1” for Event
Based CCIS, the number of digits received...

CHAPTER 4 ND-45857 (E)
Pag e 7 2
Revision 3.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Note 1:This data should be assigned to the B
channel trunk route. For D channel trunk
rute, no data setting is required.
Note:If CM35 YYY=143, is set to “1” for Event
Based CCIS, CM35 YY=18 must be set to
“0”.
T/R: Transmitter PAD/Receiver PAD
+: Gain
T/R: Transmitter PAD/Receiver PAD
+: Gain• YY=14 (SMDR for Outgoing Call)
(1)   Trunk Route No. (00-63)
(2)   0/1 : Not to be provided/To be provided
Note 1
•   YY=15...

ND-45857 (E) CHAPTER4
Addendum-001 Page 73
August, 1998 Revision 3.1
DESCRIPTION DATA
Note 1:This data should be assigned to the B
channel trunk route. For D channel trunk
route, no data setting is required.
Note 2:This data should be assigned to both B
channel trunk route and D channel trunk
route.
• YY=28 (Outgoing Trunk Queuing)
(1)     Trunk Route No. (00-63)
(2)  0: Restricted
For D channel trunk route, no data setting 
is required.
•   YY=39 (Trunk release by detection of 
reversal of tip and...

CHAPTER 2 ND-45857 (E)
Pag e 7 3-1
Revision 3.1
 
HARDWARE REQUIRED
PN-AUCA card ´ n 
DESCRIPTION DATA
When the data for CM35 YY = 18 is set to 
“0” (Received Digits Conversion is to be 
provided), assign the data for interpreting the 
digits received.• Y = 0 (Day Mode) 
• Y = 1 (Night Mode) 
(1) X-XXXX: Station Number received.
(2) X-XXXX: Station Number to be ter-
minated. 
DXX: Change Terminating System to:
D09: AUTO ATT.
D13: TAS 
D14: SN610 ATTCON
D16: DISA
END
CM76
D 

ND-45857 (E) CHAPTER 2
Addendum-001 Page 73-2
August, 1998 Revision 3.1
This page is for your notes. 

CHAPTER 4 ND-45857 (E)
Pag e 7 4
Revision 3.0
SYSTEM DATA PROGRAMMING
• For originating calls to the ISDN network, assign the following data.
• When providing Tandem Connection (Tie Line (OD/DTI) to ISDN/ISDN to Tie Line (OD/DTI)), do the fol-
lowing programming. START
DESCRIPTION DATA
Assign ISDN access code to each trunk route 
assigned by CM30 YY=00.  •
(1)
(2)Y=0-3 (Numbering Plan Group 0-3)
X-XXX (Access code)
100-163: Trunk Route No. (00-63)
Specify the timing start when making an ISDN 
call from...

ND-45857 (E) CHAPTER 4
Addendum-001 Page 75
AUGUST, 1998 Revision 3.1
SYSTEM DATA PROGRAMMING
• When providing Tandem Connection (ISDN to CCIS/CCIS to ISDN), do the following programming.
• Specify whether the Calling Party Number (CPN) sent from ISDN is sent to the CCIS network. START
DESCRIPTION DATA
Specify the combination of Trunk routes allow-
ing the tandem connection.(1) XX  XX
00-63 (Incoming Trunk Route)
00-63 (Outgoing Trunk Route)
(2)
0/1 : Allowed/Restricted
Tandem connection by station or...

CHAPTER 4 ND-45857 (E)
Pag e 7 6
Revision 3.0
SYSTEM DATA PROGRAMMING
3.3 Service Data Assignment
3.3.1 Calling Party Recognition Service (Direct-In Termination (DIT)) Assignment
Refer to “Direct Inward Termination (DIT)” in the Feature Programming Manual. 

ND-45857 (E) CHAPTER 4
Page 77
Revision 3.0
SYSTEM DATA PROGRAMMING
3.3.2 DID Addressing Assignment
DESCRIPTION DATA
Assign the data for DID to the Trunk Numbers 
assigned by CM07.• YY = 02 (Terminating System in Day 
Mode)
• YY = 03 (Terminating System in Night 
Mode)
(1) Trunk No. (000 – 255) assigned by CM07 
YY = 01
(2) 18: ISDN Indial
Assign the data for DID to the Trunk Routes as-
signed by CM30• YY = 00 (Kind of Trunk)
(1) Trunk Route No. (00 – 63)
(2) 00: DDD
• YY = 02 (OG/IC)
(1) Trunk Route No....

CHAPTER 4 ND-45857 (E)
Pag e 7 8
Revision 3.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
• YY = 18 (Received Digit Conversion)
(1) Trunk Route No. (00 – 63) 
(2) 0/1 : To be provided/Not to be provided 
Assign the destination of DID Call transferred 
when the station is busy/unassigned/no answer.• YY = 00 (No Answer)
• YY = 03 (Busy)
• YY = 06 (Unassigned)
(1) Tenant No. (00 – 63) 
(2) Destination: 
X-XXXX (Station No.)
E000 (SN610 ATTCON) 
EBXXX (Announcement Service: 
Digital Announcement Trunk 
No.)...