NEC Neax2000 Ivs Isdn System Manual

ND-45857 (E) CHAPTER 4
Page 89
Revision 3.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
• YY = 33 (Interval of ringing signal)
(1) Trunk Route No. (00 – 63)
(2) 0: 0.4s ON – 0.2s OFF – 0.4s ON–2s OFF 
1: 0.4s ON – 0.2s OFF – 0.4s ON–2s OFF 
2: 1s ON – 2s OFF
3  : When CM08 – 392 = 0:  2s ON – 4s 
OFF
3 : When CM08 – 392 = 1:  0.4s ON – 
0.2s OFF – 0.4s ON –
2s OFF
When the data for CM35 YY = 18 is set to 0, as-
sign the data for converting the received digit.• Y = 0 (Day Mode)
• Y = 1 (Night Mode)
(1)...

CHAPTER 4 ND-45857 (E)
Pag e 9 0
Revision 3.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Assign the answering method of the Automated 
Attendant to the required tenants.•Y = 0
(1) Tenant No. (00 – 63)
(2) 00: DT Connection 
02: 1st Answering Message
followed by DT Connection
03  : DT Connection
Assign the data of Hold Tone Sending. • Y = 0
(1) 00:C.O. Line
(2) 1400: Hold Tone Source on MP Card
If no Dial tone connection is required for the 
answering system assigned by CM64 Y = 0, set 
data “0”.•Y = 2
(1)...

ND-45857 (E) CHAPTER 4
Page 91
Revision 3.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Specify the Terminating System for called Par-
ty Subaddress.(1) 401
(2) 0: Station Call
1 : Terminating System assigned by 
CM30
YY = 02, 03
Specify the time before an Automated Atten-
dant call is redirected because no digits are re-
ceived from the calling party.•Y = 0
(1) 34
(2) 01 – 30:  0 – 120 sec.
If no data is set, the default setting is 32 – 36 
seconds.
Specify the timing of unanswered call after for-
warding...

CHAPTER 4 ND-45857 (E)
Pag e 9 2
Revision 3.0
SYSTEM DATA PROGRAMMING
When the 1st and/or 2nd answering message is required: CM30 YY=30, 31, Data=08/CM64 Y=0, Data=02, do
the following programming.
DESCRIPTION DATA
Assign a Digital Announcement Trunk 
Circuit No. to the required LEN.
Note:The Digital Announcement Trunk Circuit
No. must be assigned to the 1st LEN (Lev-
el 0) and/or 3rd LEN (Level 2) of each LT
slot.
(1) LEN (0000 – 0511)
(2) EB000 – EB127: Digital Announcement 
Trunk Circuit No.
EB000 –...

ND-45857 (E) CHAPTER 4
Page 93
Revision 3.0
SYSTEM DATA PROGRAMMING
3.3.11 Direct Inward System Access (DISA) Assignment
To provide the DISA without Application Processor (PN-AP01):
DESCRIPTION DATA
Designate the processor checking the ID code 
on DISA.(1) 217
(2) 0: MP (PN-CP00)
Designate the Terminating System for Called 
Party Subaddress.(1) 401
(2) 0/1  : Station Call/Terminating System 
assigned by CM30 YY = 02/03
Assign the ring rate on a DISA call. (1) 180
(2) 0/1 : 0.2s ON – 0.2s OFF – 
0.2s ON –...

CHAPTER 4 ND-45857 (E)
Pag e 9 4
Revision 3.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Assign the handling of busy/not available/unan-
swered Automated Attendant, DISA destina-
tion in Day/Night Mode.• YY = 30 (Day mode)
• YY = 31 (Night mode)
(1) Trunk No. (000 – 255)
(2) 00: C.O. Line Release 
01: Forwarded to TAS 
03: Forwarded to ATTCON 
04: Forwarded to DIT Station  assigned by 
CM30 Y = 04, 05.
06: DT Connection for redial 
08: C.O. Line Release 
15 : C.O. Line Release 
Assign the handling of...

ND-45857 (E) CHAPTER 4
Page 95
Revision 3.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Assign the data for digit conversion on DID call 
to the Route No. assigned by CM30 YY = 00 
when providing DISA to the DID call.• YY = 18
(1) Trunk Route No. (00 – 63)
(2) 0/1  : To be provided/Not to be provided
When the data for CM35 YY = 18 is set to 0, as-
sign the data for converting the received digit(s) 
to DISA.• Y = 0 (Day Mode)
• Y = 1 (Night Mode)
(1) X-XXXX:Station No. received
(2) D16: DISA
Assign the ID...

CHAPTER 4 ND-45857 (E)
Pag e 9 6
Revision 3.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Specify the maximum number of digits for ID 
Code on DISA.(1) 13
(2) 01 – 16 (Number of digits) 
If no data is set, 10 digits of ID Code are avail-
able.CM42
C
END 

ND-45857 (E) CHAPTER 4
Page 97
Revision 3.0
SYSTEM DATA PROGRAMMING
To provide the DISA with AP (PN-AP01):
DESCRIPTION DATA
Assign the slot number to the PN-AP01 card. 
The SENSE Switch on the PN-AP01 card 
should be set to the slot number assigned by this 
command. (1) Slot No. (04 – 15)
(2) 07
Designate the processor checking the DISA ID 
Codes.(1) 217
(2) 1  : AP (PN-AP01)
Designate the Terminating System for Called 
Party Subaddress.(1) 401
(2) 0/1  : Station Call/Terminating System 
assigned by CM30...

CHAPTER 4 ND-45857 (E)
Pag e 9 8
Revision 3.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Assign the Trunk Tenant. • YY = 01
(1) Trunk No. (000 – 255) 
(2) Trunk Tenant (00 – 63)
If no data is set, the default setting is 01.
Assign the Terminating System in Day/Night 
Mode for incoming C.O. Calls.• YY = 02 (Day Mode)
• YY = 03 (Night Mode)
(1) Trunk No. (000 – 255)
(2) 18:ISDN Indial
Assign the handling of busy/not available/unan-
swered Automated Attendant, DISA destina-
tion in Day/Night Mode.• YY = 30...