NEC Neax2000 Ivs Isdn System Manual

ND-45857 (E) CHAPTER 4
Page 99
Revision 3.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Specify the conditions for adding a Check Code 
to each Authorization Code.
Check Code consists of 2 digits:
1st and 2nd Check Code are generated by the 
AP according to the conditions specified by Y 
= 0 and Y = 1.
Authorization Code:
X
1 X2 X3 X4 X5 X6 X7 X8C1 C2 
ID Code programmed Check Code
X: Significant Digit for Check Code• Y = 0 (Designation of Significant digit for 
Check Code)
(1) 0: For 1st Check Code
1: For...

CHAPTER 4 ND-45857 (E)
Pag e 1 00
Revision 3.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Set the Authorization Code and its temporary 
Class of Service.
By entering the Authorization Code, the Check 
Code will be display on the MAT or CAT.•Y = 3
(1) X – X...X: Authorization Code (Max. num-
ber of digits specified by CM42-11.)
(2) A (Single Digit): In case of A = 0, 1 or 9 
ABBCCDDEE (9 digits): In case of A = 2
• Temporary Class of Service
A: Type of Temporary Class of Service
0: Unrestricted
1: Fully...

ND-45857 (E) CHAPTER 4
Page 101
Revision 3.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
When the data for CM35 YY = 18 is set to 0, as-
sign the data for converting the received digit(s) 
to DISA.• Y = 0 (Day Mode)
• Y = 1 (Night Mode)
(1) X-XXXX:Station No. received
(2) D16:DISA
Specify the maximum number of digits for ID 
Codes on DISA.
Note:The same number of digits must be as-
signed by CM42-11 and CM42-13.
(1) 11, 13
(2) 01 – 10 (Maximum Number of Digits).If 
Check Code is provided, the maximum...

CHAPTER 4 ND-45857 (E)
Pag e 1 02
Revision 3.0
SYSTEM DATA PROGRAMMING
To access the Digital Announcement Trunk (PN-2DATA) via DISA, add the following programming.
DESCRIPTION DATA
Assign a Digital Announcement Trunk Circuit 
No. to the required LEN.
Note:The Digital Announcement Trunk Circuit
No. must be assigned to the first LEN
(Level 0) and/or the third LEN (Level 2) of
each LT slot.
(1) LEN (0000-0511)
(2) EB000 – EB127: Digital Announcement 
Trunk Circuit No.
For PIM0/1: EB000 – EB031
For PIM2/3:...

ND-45857 (E) CHAPTER 4
Page 103
Revision 3.0
SYSTEM DATA PROGRAMMING
3.4 ISDN PRI Call By Call Service Selection
General
1500 Series Software enhanced ISDN PRI by providing Call By Call Services Selection. the Call By Call en-
hancements require two new components for implementation: 
• D Channel Handler (DCH) firmware upgrade to revision CB1.15
• 1500 Series CD 2.05 or higher including proper Serial ID key software
The separate sections have been implemented in LCR programming for the CBC enhancement.
•...

CHAPTER 4 ND-45857 (E)
Pag e 1 04
Revision 3.0
SYSTEM DATA PROGRAMMING
The next example details a local 7 digit call and will not used a Binary Facility Code.
CM8A405 - 2 (dialed number) = 001 (go to route pattern 000)
CM8A000 - 1 (1
st choice)=00210 (use LCR pattern 002 + trk route 10)
CM 855 - 2 = 7 (maximum number of digits dialed)
CM 8A502 - 157 =  04 (Kind of called party = Local) (dialed number is 7-digit NANP, select Local)
CM 8A502 - 158 =  01 (Called party Number Plan ID = ISDN / Telephony...

ND-45857 (E) CHAPTER 4
Page 105
Revision 3.0
SYSTEM DATA PROGRAMMING
NEAX2000 IVS Programming
Use the following programming to assign the ISDN PRI Call By Call Identification Codes.
CMA405 - 10 (dialed number) = 406 (go to table 406)
CMA406 - 288 (dialed number) = 010 (use route pattern 010)
CMA010 - 1 (1st choice) = 02010 (use LCR pattern 020 + trk route 10)
CM8A520 - 157 = 02 (Kind of called party = National)
CM8A520 - 158 = 01 (Called party Number Plan ID = ISDN / Telephony Numbering Plan)
CM8A520 -...

CHAPTER 4 ND-45857 (E)
Pag e 1 06
Revision 3.0
SYSTEM DATA PROGRAMMING
3.4.1 Call By Call Service Selection Assignment
DESCRIPTION DATA
Assign the kind of the called party number. • YYY=500-755 
(LCR/TR Pattern No. 000-255)
(1) 157 (Kind of Called Party No.)
(2) 01 : International
02 : National
03 : Network
04 : Local
05 : Not used
06 : Speed Dial
NONE :Not Sending
Assign the Called Party Numbering Plan Iden-
tifier.• YYY=500-755
(LCR/TR Pattern No. 000-255)
(1) 158
(Called Party Numbering Plan...

ND-45857 (E) CHAPTER 4
Page 107
Revision 3.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Assign the Network ID Plan Number. • YYY=500-755 
(LCR/TR Pattern No. 000-255)
(1) 160 (Network ID Plan No.)
(2) 00 :
Network ID No.
15 :
NONE : Not Sending
Assign the Network ID Character. • YYY=500-755
(LCR/TR Pattern No. 000-255)
(1) 161 (Network ID Character)
(2) X :
X=0-9, A(*), B(#)
XXX :
Specify whether Call By Call is Feature or Ser-
vice.• YYY=500-755
(LCR/TR Pattern No. 000-255)
(1) 162 (Feature/Service)
(2) 0...

CHAPTER 4 ND-45857 (E)
Pag e 1 08
Revision 3.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Assign the WATS Band Number. • YYY=500-755 
(LCR/TR Pattern No. 000-255)
(1) 164 (WATS Band No.)
(2) 00 :
WATS Band No.
09 :
NONE : Not SendingCM8A
B
END
~