NEC Neax2000 Ivs Isdn System Manual

ND-45857 (E) CHAPTER 4
Page 61
Revision 3.0
CHAPTER 4 SYSTEM DATA PROGRAMMING
1. GENERAL
This chapter describes the programming procedure for providing ISDN to the PBX.
2. SYSTEM DATA PROGRAMMING INFORMATION
In the programming procedure, the meaning of (1), (2) and markings are as follows.
(1) : 1st Data
(2) : 2nd Data
: Initial Data
With the system data clear command (CM00, CM01), the data with this marking is
automatically assigned for each command.
: System Initialization
After entering the data,...

CHAPTER 4 ND-45857 (E)
Pag e 6 2
Revision 3.0
SYSTEM DATA PROGRAMMING
3.1 Basic Data Assignment for ISDN with PRI
3.1.1 DTI Assignment
DESCRIPTION DATA
Assign a slot number to the DTI card.
(PN-24DTA/24DTA-A).
The slot number assigned must coincide with 
the value set by the SENS switch on the DTI 
card.(1) Slot No. (04-15)
(2) 09: DTI card
Assign ISDN Trunk No. to each channel  num-
ber on the DTI card.
Note:The system allocates time slots to consec-
utive channels from lowest to highest
channel number...

ND-45857 (E) CHAPTER 4
Page 63
Revision 3.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Assign a Trunk Route to each ISDN trunk used 
for Voice channel (B channel), and also to 
signaling channel (D channel). Make a separate 
route for B channels and D channels.
Note:DTI route must be separated from analog
trunk routes.
•
(1)
(2)YY=00
Trunk No. (000-255) assigned by CM07 
YY=01
Trunk Route No. (00-63)
Assign the trunk route data to each ISDN 
incoming trunk used for Voice channel only.
Note:If CM35 YYY=143...

CHAPTER 4 ND-45857 (E)
Pag e 6 4
Revision 3.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Note 1:This data should be assigned to the B
channel trunk route.
Note 2:This data should be assigned to both B
channel trunk route and D channel trunk
ro ut e.
• YY=05 (Release Signal from Distant 
Office)
(1)
(2)B channel/D channel Route No. (00-63)
1 : Release signal arrives
Note 2
• YY=09 (Incoming Connection Signaling)
(1) B channel Route No. (00-63)
(2) 08: ISDN
(1) D channel Route No. (00-63)
(2) 15 : Not used
•...

ND-45857 (E) CHAPTER 4
Page 65
Revision 3.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
•
(1)
(2)
•
(1)
(2)YY=18 (Digit conversion on DID call)
Trunk Route No. (00-63)
0 : To provide
1  : Not provided
YY=19
Trunk Route No. (00-63)
0:
1: Programmable PAD 
2: (See CM42)
3:
4:
5: Fixed PAD
6: (See left table)
7:
Note
T/R: Transmitter PAD/Receiver PAD
+: Gain
Note:This data should be assigned to the B
channel trunk route.
•
(1)
(2)YY=28 (Outgoing Trunk Queuing)
Trunk Route No. (00-63)
0: Restricted
For D...

CHAPTER 4 ND-45857 (E)
Pag e 6 6
Revision 3.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
When using the programmable PAD (CM35 
YY = 19, 2nd Data = 0-3), assign the PAD 
data.(1)
(2)50-65
00-15
T/R: Transmitter PAD/Receiver PAD
+: GainCM42
D
END
PAD DATA PATTERNS
CONNECTING
PATTERNS CM35 YY=19
2ND DATA=0CM35 YY=19
2ND DATA=1CM35 YY=19
2ND DATA=2CM35 YY=19
2ND DATA=3
50
6550 54 58 62 STA/TONE-DTI
51 55 59 63 COT/LDT-DTI
52 56 60 64 ODT-DTI
53 57 61 65 DTI-DTI
1ST
DATA
~
PAT T E R N
PAD DATA OF DTI (T/R)...

ND-45857 (E) CHAPTER 4
Page 67
Revision 3.0
SYSTEM DATA PROGRAMMING
• For originating calls to the ISDN network, assign the following data.
DESCRIPTION DATA
Assign ISDN access code to each trunk route
assigned by CM30 YY=00.
Note:LCR can be used with ISDN-PRI. Refer to
Feature Programming Manual.
• Y=0-3 (Numbering Plan Group 0-3)
(1) X-XXX (Access code)
(2) 100-163: Trunk Route No. (00-63)
Specify the timing start when making an ISDN 
call from SN610 ATTCON.(1) 403
(2) 0/1 : Not Available/Available...

CHAPTER 4 ND-45857 (E)
Pag e 6 8
Revision 3.0
SYSTEM DATA PROGRAMMING
• When providing Tandem Connection (Tie Line (OD/DTI) to ISDN — ISDN to Tie Line (OD/DTI)), do the
following programming.
• When providing Tandem Connection (ISDN to CCIS — CCIS to ISDN), do the following programming.
DESCRIPTION DATA
Specify the combination of Trunk Routes 
allowing the tandem connection.(1) XX  XX
00-63 (Incoming Trunk Route)
00-63 (Outgoing Trunk Route)
(2) 0/1  : Allowed/Restricted 
Specify the timing start when...

ND-45857 (E) CHAPTER 4
Addendum-001 Page 69
AUGUST, 1998 Revision 3.1
SYSTEM DATA PROGRAMMING
3.1.2 DCH Assignment
DESCRIPTION DATA
Assign a slot number to the DCH card 
(PN-SC01).
The slot number assigned must coincide with 
the value set by the SENS switch on the 
PN-SC01 card.(1) Slot No. (04 – 15)
(2) 12: PN-SC01 card 
Assign the ISDN protocol type to a slot number 
assigned by CM05.•
(1)
(2)YY=06
Slot No. of DCH (04-15) assigned by 
CM05
20:  AT&T (No. 4, No. 5 ESS)
21:  NTI (DMS 100, 250)
28:...

CHAPTER 4 ND-45857 (E)
Page 70 Addendum-001
Revision 3.1 AUGUST, 1998
SYSTEM DATA PROGRAMMING
3.2 Basic Data Assignment for ISDN with BRI
3.2.1 BRI 
Assignment
DESCRIPTION DATA
Assign a slot number to the BRI card. 
The slot number assigned must coincide with 
the value set by the SENS switch on the BRI 
card. 
Specify ISDN protocol type to a slot number 
assigned by CM05.
Assign ISDN Trunk No. to each Channel No. of 
BRI Trunk. 
Assign Trunk Route to each ISDN trunk used 
for Voice channel (B channel)....