NEC Neax2000 Ivs Isdn System Manual

ND-45857 (E) CHAPTER 3
Page 33
Revision 3.0
INSTALLATION
STEP 2: Mount the DTI card and the DCH card in AP slots on PIM0-PIM7.
After mounting the card, set the SENS switch to match an unequipped slot number in CM05. And set
the MB switch to down position to put the card in service. For details on mounting locations, refer to
the Circuit Card Manual.
Figure 3-5   Mounting Location of DTI/DCH Card
DTI/DCH
CARDBUILT-IN BATTERY
• Mount DTI card in the AP slots (AP0-AP6).
• Mount DCH card in the AP slots...

CHAPTER 3 ND-45857 (E)
Page 34 Addendum-001
Revision 3.1 AUGUST, 1998
INSTALLATION
4.1.2 Selection of PLO in MP Card
STEP 1: On the MP (PN-CP00/CP00-B/CP03) card, set the switches as shown in Figure 3-6.
Figure 3-6   Switch Settings on the MP Card (1/3)
RU N
SW2
ON 
 
 
 
 
 
 
 
OFF
0: ON LINE MODE
: POSITION TO BE SET
1 2 3 4
JP0
SW3
CLKIN
JP0
RS
ON: KF MODE
OFF: PF/MF MODE (STANDARD SETTING
FOR U.S.A.)
SW1
SW2
ATTENTIONContents
Static Sensitive
Handling
Precautions Required
• PN-CP00
• WHEN USING THE...

ND-45857 (E) CHAPTER 3
Addendum-001 Page 35
AUGUST, 1998 Revision 3.1
INSTALLATION
Figure 3-6  Switch Settings on the MP Card (2/3)
SW3
RUN
SW1
SW2
CLKIN
JP0
0: ON LINE MODE
JP0
:  POSITION TO BE SET
•  PN-CP00-B
• WHEN USING THE INTERNAL PLO • WHEN USING THE PLO CARD
SW2-2 SW2-3 SW2-2 SW2-3
OFF OFF : 1.5 MHz CLOCK
  (FOR 24-DTI)OFF ON
ON OFF : 192 KHz CLOCK
  (FOR BRTA)
OFF ON : 2 MHz CLOCK
  (FOR 2BRTC)
ON ON : NOT USED
• WHEN THE INTERNAL PLO AND THE
PLO CARD ARE NOT USED
SW2-2 SW2-3
OFF OFF
SW2OFF
ON...

CHAPTER 3 ND-45857 (E)
Page 36 Addendum-001
Revision 3.1 AUGUST, 1998
INSTALLATION
Figure 3-6  Switch Settings on the MP Card (3/3)
STEP 2: Mount the MP card on the MP slot of PIM0.
SW2SW2
OFFON
4
 
3 2 1 
 
SW3: POSITION TO   BE SET
:  POSITION TO BE SET
 0: ON LINE MODE
ON:   KF MODE
OFF:  PF/MF MODE (STANDARD 
SETTING FOR U.S.A.) 
• WHEN USING THE INTERNAL PLO
SW2-2 SW2-3
OFF OFF : 1.5 MHz CLOCK
(FOR 24-DTI)
ON OFF : 192 KHz CLOCK
(FOR BRTA)
OFF ON : 2 MHz CLOCK
(FOR 2BRTC)
ON ON : NOT USED
• WHEN...

ND-45857 (E) CHAPTER 3
Addendum-001 Page 37
AUGUST, 1998 Revision 3.1
INSTALLATION
4.1.3 Cable Connection via the MDF for ISDN with PRI
When using a twisted-pair cable, connect the cable to a CSU via the MDF as shown in Figure 3-7.
Figure 3-8 shows LTC connector corresponds with the AP slots, and DTI pin assignment for each AP slot, and
Figure 3-9 shows an example of the cable connection when the DTI card is mounted in the AP0 slot of PIM0.
Figure 3-7   Cable Connection via the MDF for ISDN with PRI
CSU...

CHAPTER 3 ND-45857 (E)
Pag e 3 8
Revision 3.0
INSTALLATION
Figure 3-8   Location of the AP Slots and the LTC Connectors for DTI
126
LT061RA26RB
LT12/AP2 2 27 2 TA 27 TB
328 328
429 429
530
LT075RA30RB
LT13/AP3 6 31 6 TA 31 TB
732 732
833 833
934
LT089RA34RB
LT14/AP4 10 35 10 TA 35 TB
11 36 11 36
12 37 12 37
13 38
LT0913 RA 38 RB
LT15/AP5 14 39 14 TA 39 TB
15 40 15 40
16 41 16 41
17 RA 42 RB
LT10/AP017 RA 42 RB
AP6 18 TA 43 TB 18 TA 43 TB
19 44 19 44
20 45 20 45
21 RA 46 RB
LT11/AP121 46
22 TA 47 TB 22...

ND-45857 (E) CHAPTER 3
Page 39
Revision 3.0
INSTALLATION
Figure 3-9   Example of Cable Connection via the MDF for DTI
TO
PIM0
PN-24DTA/24DTA-A
RECEIVE
SEND
TO CSU JP MDFLT C 1
12
1
2
39 38 37 36 35 34 33 32 31
TB TA RB RA
RA
RB
TA
TB T0-31
32
33
34 AA0
BA0
AA1
BA117
42
18
4317
42
18
43
17
18
19
20RA
TA42
43
44
45RB
TB42
43
44
4517
18
19
20RA
TA RB
TB LTC1 CONNECTOR
LTC (J) (P)
MDF CONNECTOR AP0
[LT10] 

CHAPTER 3 ND-45857 (E)
Page 40 Addendum-001
Revision 3.1 AUGUST, 1998
INSTALLATION
4.1.4 Mounting PLO Card
STEP 1: On the PLO (PN-CK00) card, set the switches as shown in Figure 3-10.
Figure 3-10   Switch Settings on the PLO Card
STEP 2: On the MP card, set the SW2-2 to OFF and SW2-3 to ON.
MB
SW
SYNC
PLO0
PLO1
OFF
ON 8 
7 
6 
5 
4 
3 
2 
1
SW0MB
: POSITION TO 
  BE SET
UP
ALM
DRFT
ATTENTIONContents
Static Sensitive
Handling
Pr ec autions  Re quire d
• SELECTION OF PLO 0 • SELECTION OF PLO 1
SW0-1 SW0-2...

ND-45857 (E) CHAPTER 3
Page 41
Revision 3.0
INSTALLATION
STEP 3: Mount the PLO (PN-CK00) card in an AP slot on PIM0
After mounting the card, set the MB switch to down position to put the card in service. For details on
mounting locations, refer to the Circuit Card Manual.
Figure 3-11   Mounting Location of the PLO Card
PIM0 
LT00 LT01
LT02 LT03 LT04 LT05 LT06 LT07 LT08
LT09 LT10/AP0
LT11/AP1
LT12/AP2 LT13/AP3 LT14/AP4 LT15/AP5AP6 MP/FP/AP7BUS/AP8
PN-CK00BUILT-IN BATTERY
PWR
• Mount the PN-CK00 card in an...

CHAPTER 3  ND -4 5857 ( E)
IN STA LLA TION
E N D
CABLE CONNEC TION
S E LEC TIO N  OF P LO  IN
MOUNTI NG P LO CARD
N ote :  PLO ca rd (P N-CK00 ) i s  r e qu ir e d  when th e P B X is  a ma ste r o ffic e, or wh en  th e P B X r eq uir e s to  int erfa ce