NEC Neax2000 Ivs Isdn System Manual

ND-45857 (E) CHAPTER 3
Page 51
Revision 3.0
INSTALLATION
Figure 3-19  Switch Settings on the ICH Card (2/2)
MB
RU N
MB
DOPE7
SET THE SENS SWITCH TO 
MATCH THE AP NO. (04-15) 
TO BE SET BY CM05.SENSSENS
UP
ATTENTIONContents
Static Sensitive
Handling
Precautions Required
DOPE6
DOPE5
DOPE4
DOPE3
DOPE2
DOPE1
DOPE0
• PN-SC03
Note:Firmware must be CE0.01. 

CHAPTER 3 ND-45857 (E)
Pag e 5 2
Revision 3.0
INSTALLATION
STEP 2: Mount the ICH card in AP slots on PIM0-PIM7.
After mounting the card, set the SENS switch to match an unequipped slot number in CM05. And set
the MB switch to down position to put the card in service. For details on mounting locations, refer to
the Circuit Card Manual.
Figure 3-20   Mounting Location of the ICH Card
ICH 
CARD
BUILT-IN BATTERY
• Mount the ICH card in the AP slots (AP0-AP8).
• Set the SENS switch on the ICH card to match an...

ND-45857 (E) CHAPTER 3
Page 53
Revision 3.0
INSTALLATION
4.3.2 Mounting ILC Card
STEP 1: On the ILC (PN-2ILCA) card, set the switches as shown in Figure 3-21.
Figure 3-21   Switch Settings on the ILC Card
SW1
SW1
ON
OFF
1 2
3 4
ATTENTIONContents
Static Sensitive
Handling
Precautions Required
SW0
ACT 0
PA L 0
LPB0
B20
B10
ACT 1
PA L 1
LPB1
B21
B11
SW0
ON
OFF
1 2 3 4
: POSITION TO BE SET
: POSITION TO BE SET 

CHAPTER 3 ND-45857 (E)
Pag e 5 4
Revision 3.0
INSTALLATION
STEP 2: Mount the ILC card in LT slots on PIM0-PIM7.
Figure 3-22   Mounting Location of the ILC Card
ILC CARDBUILT-IN BATTERY
• Mount the ILC card in the LT slots (LT00-LT15).
PIM
0 - 7
P
W
R
LT 0 0LT 0 1LT 0 2LT 0 3LT 0 4LT 0 5LT 0 6LT 0 7LT 0 8LT 0 9LT10/AP0LT11/AP1LT12/AP2LT13/AP3LT14/AP4LT15/AP5
AP6
MP/FP/AP7BUS/AP8
ATTENTIONContents
Static Sensitive
Handling
Precautions Required 

ND -4 5857 ( E)  CHAPTER 3
IN STA LL AT ION
M odu la r C on ne cto r 

CHAPTER 3 ND-45857 (E)
Pag e 5 6
Revision 3.0
INSTALLATION
Figure 3-24   Location of the LT Slots and the LTC Connectors for ISDN Terminal
LT15/AP5FP/AP6MP/FP/AP7BUS/AP8
LT14/AP4
LT13/AP3
LT12/AP2
LT11/AP1
LT 0 0 LT 0 1
LT 0 2 LT 0 9
LT 0 4 LT 0 8
LT 0 7
LT 0 3 LT 0 6
LT 0 5 LT10/AP0
LT C 0 LT C 2LT C 1 PIM
0 - 7P
W
R
LTC0 LTC1 LTC2
1RA026RB0
LT 0 01 RA0 26 RB0
LT 0 61RA026RB0
LT 1 2 / A P 2 2 TA0 27 TB0 2 TA0 27 TB0 2 TA0 27 TB0
3 RA1 28 RB1 3 RA1 28 RB1 3 RA1 28 RB1
4 TA1 29 TB1 4 TA1 29 TB1 4 TA1 29...

ND-45857 (E) CHAPTER 3
Page 57
Revision 3.0
INSTALLATION
Figure 3-25   Example of Cable Connection via the MDF for ISDN Terminal
29B03 294
A0328
B02 283
A02 327
B01 2726
B00 26
2
1
26 RB 1 RA
27 TB 2 TA
28 3
29 4
(P)
1RA26RB
2TA27TB
328
429
LTC (J)MDF
A00 1
A01 2
PIM0
P ILC
LT 0 0LT C 0
J
4
RA
RB
TA
TB
SEND
3
6
4
5
12 8 7
6 5 4 2 T0-1
3RECEIVE
TO ISDN
TERMINAL
Pin No.
12
3
4
5
6
7 8
1LTC1 CONNECTOR
2MDF CONNECTOR
123456 7
RA RB TA TB
T0
Pin No. PBX Direction of Signal Terminal
1
Not Used
2
3RA¬TA
4TA®RA...

CHAPTER 3  ND -4 5857 ( E)
IN STA LLA TION
E N D
CABLE CONNEC TION
S E LEC TIO N  OF P LO  IN
MOUNTI NG P LO CARD
N ote :  PLO ca rd (P N-CK00 ) i s  r e qu ir e d  when th e P B X is  a ma ste r o ffic e, or wh en  th e P B X r eq uir e s to  int erfa ce
MOUN TING CCH C ARD 

ND-45857 (E) CHAPTER 3
Page 59
Revision 3.0
INSTALLATION
4.4.1 Mounting CCH Card
STEP 1: On the CCH card, set the switches as shown below.
Figure 3-27   Switch Settings on the CCH Card
STEP 2: Mount the CCH card into one of the AP slots on PIM0-PIM7.
After mounting the card, set the MB switch to down position to put the card in service.
For details on switch settings and mounting location, refer to the Circuit Card Manual.
Figure 3-28   Mounting Location of the CCH Card
SLOT No. SETTING:
SLOT No. SET BY...

CHAPTER 3 ND-45857 (E)
Pag e 6 0
Revision 3.0
This page is for your notes.